制备方法对MoO_3／ZrO_2结构的影响及MoO_3／ZrO_2固体超强酸的结构特征 Ⅰ．ZrO_2的形态与样品比表面的研究

ＸＲＤ，ＤＴＡ，比表面测定等结果表明，制备方法对ＭｏＯ３／ＺｒＯ２结构有决定性影响．仲钼酸铵浸渍仅经干燥的Ｚｒ（ＯＨ）４再经高温焙烧所得团体超强酸ＭｏＯ３／ＺｒＯ２（Ⅰ）与浸渍晶态ＺｒＯ２所得部分氧化催化剂ＭｏＯ３／ＺｒＯ２（Ⅱ）的载体形态有明显不同．（１）ＭｏＯ３／ＺｒＯ２（Ⅰ）的比表面数倍于ＭｏＯ３／ＺｒＯ２（Ⅱ）；（２）ＭｏＯ３含量增加时，ＭｏＯ３／ＺｒＯ２（Ⅰ）的比表面逐步增大至一极大值再缓缓下降，而ＭｏＯ３／ＺｒＯ２（Ⅱ）的比表面随ＭｏＯ３含量增加而单调下降；（３）在ＭｏＯ３／ＺｒＯ２（Ⅰ）中，ＺｒＯ２以介稳四方相存在，而在ＭｏＯ３／ＺｒＯ２（Ⅱ）中则是稳定的单斜相．在此基础上研究了事先引入的活性组分在载体织构形成过程中的作用，包括延迟ＺｒＯ２晶化，阻碍晶粒长大及与之相关的相变等，并讨论了ＭｏＯ３／ＺｒＯ２（Ⅰ）中ＭｏＯ３最佳含量的科学含义．     

制备方法对WO_3/ZrO_2结构的影响

用XRD、比表面测定、LRS定性和定量的方法对用Zr（OH）4和已晶化的ZrO2作载体制得的两类WO3／ZrO2催化剂进行了表征．揭示了样品比表面、载体物相、活性组分的存在状态与制备方法、WO3含量、焙烧温度之间的关系．结果表明，WO3能单层分散在ZrO2上；单层覆盖在Zr（OH）4上的WO3使载体在焙烧时晶粒生长受阻，形成介稳的四方ZrO2，并阻止载体微粒间的烧结，使从Zr（OH）4出发制得的WO3／ZrO2比表面明显增大，在WO3含量达到单层分散容量时以上作用表现得最充分；WO3与Zr（OH）4（或四方ZrO2）在高温（～800℃）可能发生了某种化学结合，开创出超强酸位．用以上观点可对文献中已报导的主要实验事实作出较满意的解释.     

制备方法对MoO3/ZrO2结构的影响及MoO3/ZrO2固体超强酸的结构特征Ⅰ.ZrO2的形态与样品?

ＬＲＳ，ＸＲＤ，ＸＰＳ结果表明，仲钼酸铵浸渍仅经干燥的Ｚｒ（ＯＨ）４，再焙烧制得的固体超强酸（ＭｏＯ３／ＺｒＯ２（Ｉ））与浸渍晶态ＺｒＯ２制得的部分氧化催化剂（ＭｏＯ３／ＺｒＯ２（Ⅱ）中，活性组分的存在形式明显不同，在ＭｏＯ３／ＺｒＯ２（Ⅱ）中，ＭｏＯ３以二维聚钼酸根和Ｍｏ－Ｏ－Ｚｒ表面物种两种表面态存在于介稳的四方ＺｒＯ２上，后者在ＬＲＳ谱中表现为～８１４ｃｍ＾－１的宽峰，ＭｏＯ３含量超过一定值     

制备高比表面负载型催化剂的一种新方法

In this paper, a new way to increase the specific surface areas of supported catalysts has been suggested. The results for MoO_3/ZrO_2, WO_3/ZrO_2, CuO/ZrO_2, SO_4~(2-)/ZrO_2, NiO/ZrO_2, Fe_2O_3/ZrO_2, Fe_2(SO_4)_3/ZrO_2, MoO_3/TiO_2, WO_3/TiO_2, SO_4~(2-)/TiO_2, NiSO_4/TiO_2, NiO/TiO_2, V_2O_5/TiO_2 etc. systems show that the specific surface areas of the samples, prepared by impregnating some hydroxides then calcinating at high temperature, are much larger than those of the samples prepared with a traditional method——impregnating their oxides calcinated at the same temperature. Using this way, the specific surface areas of some supported catalysts can increase by several times. The surface areas of some supports such as zirconia and titania are not large enough, and they are easy to sinter at high temperature. In these cases, the advantage of of this preparation method is fully displayed, and the specific surface areas of the resulting zirconia-or titania-supported catalysts can compare favourably with those of the catalysts prepared from some classical supports (such ar γ-Al_2O_3, SiO_2).In addition, it has been proved by means of XPS, XRD, LRS, and DTA that as an active component disperse on a support as a monolayer and its content comes up to its monolayer dispersion capacity, the specific surface area of the obtained catalyst would be the largest. We suggest a mechanism that an active component covered on a support can not only segregate its particles, but also hinder the surface diffusion of support, and as a result, its crystalline growth, an accompanying phase transformation and inter-crystalline sintering are all retarded.     

制备方法对WO3/ZrO2结构的影响

WO3/ZrO2 catalysts prepared from Zr(OH)4 and crystallized ZrO2 have been characterized by means of XRD, LRS (qualitative and quantitative), and the specific sufrace area has been measured. The influence of the preparation method, the contents of WO3 in the samples and the calcination tempearture on the specific surface areas of the samples, the phase of support and the structural states of active component has been studied. The results show: (1) WO3 can disperse on ZrO2 as a monolayer; (2) WO3 dispersed on Zr(OH)4 as a monolayer retards the crystalline growth of the support on calcination, makes it crystallizing into a metastable tetragonal modification, and prevents the inter- crystalline sintering between the crystallites of ZrO2. These factors would result in an increase in the specific surface area of WO3／ZrO2 prepared from Zr(OH)4. As the content of WO3 in the sample comes up to its monolayer capacity, this effect is displayed most fully. A chemical reaction can occur between WO3 and Zr(OH)4 (or the tetragonal ZrO2) at a high temperature(800℃),producing some superacid sites on the surface. By these views, the main experimental facts published in the literatures can been interpreted satisfactotily.     

制备高比表面负载型催化剂的一种新方法

制备具有大比表面、适宜孔结构的催化剂一直是催化剂研究的重要课题之一.近年,氧化锆、氧化钛载体以其独特性能引起多方面的关注.然而,这两种载体不但本身比表面较小,而且在高温灼烧时比表面急剧下降,所以很难制成高比表面催化剂,极大地限制了它们的应用.本文提出一种制备高比表面负载型催化剂的新方法,它特别适用于TiO_2、ZrO_2.它是在以下两个想法的基础上提出的.(1)我们在工作中曾发现,将仲钼酸铵加到Ti(OH)_4中,经500℃、4小时焙烧,所得的MoO_3/TiO_2(MoO_3质量分数为13.0%)比表面可达133m~2·g~(-1).而用仲钼酸铵浸渍已晶化     

制备方法对MoO_3／ZrO_2结构的影响及MoO_3／ZrO_2固体超强酸的结构特征 Ⅱ．活性组分存在形态的研究

ＬＲＳ，ＸＲＤ，ＸＰＳ结果表明，仲钼酸铵浸渍仅经干燥的Ｚｒ（ＯＨ）４再焙烧制得的固体超强酸（ＭｏＯ３／ＺｒＯ２（Ⅰ））与浸渍晶态ＺｒＯ２制得的部分氧化催化剂（ＭｏＯ３／ＺｒＯ２（Ⅱ）中，活性组分的存在形式明显不同．在ＭｏＯ３／ＺｒＯ２（Ⅱ）中，ＭｏＯ３以二维聚钼酸根形式单层分散在ＺｒＯ２上（其中单斜ＺｒＯ２为主），在～９５０ｃｍ－１处出现特征拉曼宽峰，超出单层分散容量的部分以晶态ＭｏＯ３形式存在．在ＭｏＯ３／ＺｒＯ２（Ⅰ）中，活性相以二维聚钼酸根和Ｍｏ—Ｏ—Ｚｒ表面物种两种表面态存在于介稳的四方ＺｒＯ２上，后者在ＬＲＳ谱中表现为～８１４ｃｍ－１的宽峰；ＭｏＯ３含量超过一定值时，多余的ＭｏＯ３在５５０℃即与四方ＺｒＯ２发生反应形成体相Ｚｒ（ＭｏＯ４）２．Ｍｏ—Ｏ—Ｚｒ表面物种中，Ｍｏ（Ⅵ）是四配位的，与四方ＺｒＯ２结合很强，它很可能与ＭｏＯ３／ＺｒＯ２具有超强酸性有密切关系．     

制备方法对MoO3/ZrO2结构的影响及MoO3/ZrO2固体超强酸的结构特征Ⅱ.活性组分存在形态?

ＬＲＳ，ＸＲＤ，ＸＰＳ结果表明，仲钼酸铵浸渍仅经干燥的Ｚｒ（ＯＨ）４，再焙烧制得的固体超强酸（ＭｏＯ３／ＺｒＯ２（Ｉ））与浸渍晶态ＺｒＯ２制得的部分氧化催化剂（ＭｏＯ３／ＺｒＯ２（Ⅱ）中，活性组分的存在形式明显不同，在ＭｏＯ３／ＺｒＯ２（Ⅱ）中，ＭｏＯ３以二维聚钼酸根和Ｍｏ－Ｏ－Ｚｒ表面物种两种表面态存在于介稳的四方ＺｒＯ２上，后者在ＬＲＳ谱中表现为～８１４ｃｍ＾－１的宽峰，ＭｏＯ３含量超过一定值