Optimal design of gears contact interface modification for an objective as minimum impact resistance of initial meshing-in time domain

Meccanica - In gear pair actual alternating meshing process, the comprehensive errors of the transmission system and the thermal elastic deformation of the teeth body cause the gears in the meshing...     

紧黎曼流形上的椭圆边界值问题

讨论一类非齐次非线性椭圆边界值问题.利用极大值原理证明了该问题解的梯度估计.作为它的应用得到了解的效率比估计.     

80.5 MeV/u碳离子诱发铜靶的放射性剩余产物测量

高能重带电粒子能直接穿透靶原子核外电子层,与原子核发生直接碰撞,发生散裂反应,产生一系列具有放射性的剩余产物核.重带电粒子诱发靶材放射性剩余核与辐射防护和人员安全有着密切联系,当前,大部分剩余核产额主要依靠蒙特卡罗粒子输运程序进行模拟计算,其准确程度亟需通过实验测量进行准确评估.本文利用能量为80.5 MeV/u的(12)^C⁶⁺粒子对薄铜靶开展了辐照实验与伽玛射线测量,结合伽玛谱学分析方法,得出了辐照产生的18种放射性剩余产物的初始活度和产生截面值,并与PHITS模拟结果进行对比.结果表明,PHITS模拟程序对放射性剩余核种类的估计具有较高可靠性,在其绝对产额方面,与实验测量仍具有较大偏差.     

LD泵浦Nd∶LuVO4/Cr4+∶YAG被动调Q激光器

采用大功率半导体激光器端面泵浦Nd∶LuVO4晶体，利用Cr4+∶YAG晶体作为可饱和吸收元件，实现了1.06 μm激光的被动调Q运转.在泵浦功率为19.1 W时，获得最高平均输出功率为4.58 W，脉冲宽度为84 ns，单脉冲能量为36.6 μJ以及峰值功率为436.2 W的激光脉冲.     

用能量法求多自由度振动系统的角频率

利用简谐振动能量方程，通过分析振幅矢量的关系，用能量法求多自由度振动系统的角频率或简正振动频率。     

Laser-induced damage of Ta2O5/SiO2 narrow-band interference filters under different 1064 nm Nd:YAG laser modes

The laser-induced damage (LID) behavior of narrow-band interference filters was investigated with a Nd:YAG laser at 1064 nm under single-pulse mode and free-running mode. The absorption measurement of such coatings was performed with surface thermal lensing (STL) technique. The damage morphologies under the two different laser modes were also studied in detail. It was found that all the filters exhibited a pass-band-center-dependent absorption and laser-induced damage threshold (LIDT) behavior, but the damage morphologies were diverse. The explanation was given with the analysis of the electric field distribution and the operational behavior of the irradiation laser.     

Vacuum System for HL-2A Tokamak

The vacuum system of today＇s tokamak devices is designed to meet the operational requirements of the experiments. The operation can be divided into five modes, （1） pumping down and leak detecting of the vacuum vessel, （2） baking, （3） plasma-facing component （PFC） conditioning, （4）evacuating and controlling of the particles at plasma edge, （5） plasma discharge experiments.     

Optimality Conditions and Geometric Properties of a Linear Multilevel Programming Problem with Dominated Objective Functions

In this paper, a model of a linear multilevel programming problem with dominated objective functions (LMPPD(l)) is proposed, where multiple reactions of the lower levels do not lead to any uncertainty in the upper-level decision making. Under the assumption that the constrained set is nonempty and bounded, a necessary optimality condition is obtained. Two types of geometric properties of the solution sets are studied. It is demonstrated that the feasible set of LMPPD(l) is neither necessarily composed of faces of the constrained set nor necessarily connected. These properties are different from the existing theoretical results for linear multilevel programming problems.     

Microstructure of laser melted Al18B4O33w/2024Al composite

The microstructure of a laser treated Al₁₈B₄O₃₃w/2024Al composite has been investigated using transmission electron microscope (TEM), low-angle (glancing angle) X-ray diffraction (XRD) techniques. Various surface microstructures were observed in the laser treated composite. The Al₁₈B₄O₃₃ whisker on the surface of the composite was decomposed during laser surface melting, various decomposition products were studied in the laser treated composite. Eutectic phases and the precipitation in the matrix of the composite with laser-treated were observed. The main phases detected in the molten zone were aluminum and decomposition products Al₂O₃. The effect of laser treatment on the hardness of the composite was also examined. A surface hardness of 400 Hv was noted.