Wavelength-Dependent Transient Characteristics Caused by Gain Saturation in Highly Nonlinear Fiber-Based Raman Amplifiers

We have investigated the transient characteristics of discrete Raman Amplifiers and found that the response time caused by gain saturation is dependent upon the wavelength, which corresponds to the effective length of the pump light.     

Effect of solute atoms on fracture toughness in dilute magnesium alloys

The effect of alloying elements on the toughness and the fracture behaviour was investigated on seven kinds of Mg-0.3?at.% X (X?=?Ag, Al, Ca, Pb, Sn, Y and Zn) alloys with a grain size of 3–5?μm. The fracture toughness and fracture behaviour in magnesium alloys were closely related to the segregation energy. The Mg–Al and –Zn alloys that had small segregation energy showed high toughness and ductile fracture in most regions, while the Mg–Ca alloy with large segregation energy exhibited low toughness and intergranular fracture. These different tendencies resulted from solute segregation at grain boundaries (GBs). The change in the lattice parameter ratio was the influential material parameter regardless of whether the GB embrittlement was for enhancement or suppression.     

Effects of severe plastic deformation on the corrosion behavior of aluminum alloys

Effects of severe plastic deformation on the corrosion behaviors of Al alloys containing precipitates have been investigated. Al and its alloys were severely deformed by equal-channel angular pressing (ECAP) processes and the corrosion behaviors of the Al alloys were evaluated by means of potentiodynamic polarization in a neutral buffer solution containing 0.002 M chloride ion. Introduction of huge plastic deformation to both of Al-5.4 wt% Ni and Al-5 wt% Cu alloys increased pitting potential. In contrast, ECAP treatment of 4N pure Al resulted in a decrease in open circuit potential, slight increase of passive current and shift of pitting potential to the negative direction. The influence of the change in microstructures caused by severe plastic deformation was investigated. Contribution to the Fall Meeting of the European Materials Research Society, Symposium D: 9th International Symposium on Electrochemical/Chemical Reactivity of Metastable Materials, Warsaw, 17th-21st September, 2007     

One-dimensional shock wave interaction with rubber and low-porosity foam

One-dimensional interaction between a planar shock wave and a rubber or low-porosity foam is investigated experimentally and numerically. The considered polyurethane foam is of high density (ρ _c=290 kg/m³) and lowporosity (ϕ=0.76), and this corresponds to an intermediate condition between rubber and high-porosity foam. Stress-strain relations for the low-porosity foam are investigated by machine tests, which show larger deformation against compressive force and higher non-linearity in stress-strain curve as compared with rubber. Also the low-porosity foam shows a hysteresis cycle. Experiments on shock wave-foam interactions are conducted by using a shock tube. Experimental time history of the surface stress of the foam at the end of the shock tube does not show shock type stress increase, but continuous excessive stress rise can be seen, and then dumping vibration approaching to gas dynamic pressure of the reflected shock wave is followed, and the highest stress amounts about 3∼4 times of the pressure after the reflected gas dynamic shock wave. Interactive motions of gas and the low-porosity foam are analyzed using the Lagrangean coordinates system. An elastic model for a low-porosity foam is assumed to be a single elastic material with the measured stress-strain relation. Results of numerical simulations are compared with the shock tube experiments, which show essentially same stress variations with experimental results.     

Selective appearance of ϵ-martensitic transformation and dynamic strain aging in Fe–Mn–C austenitic steels

The influence of stress-induced ε-martensitic transformation on the serrated flow behavior associated with dynamic strain aging was investigated. The ε-martensitic transformation was controlled by changing the deformation temperature and adding Si to Fe–17Mn–xSi–0.3?C alloys. The addition of Si promoted the ε-martensitic transformation, and suppressed the slip deformation due to solution hardening. The initiation of serrations around room temperature was delayed by the promotion of ε-martensitic transformation which initiated plastic deformation. The critical stress for the occurrence of serrations and the critical stress for the occurrence of slip deformation were found to have a linear relationship.     

Constant-load delayed fracture test of atmospherically corroded high strength steels

Constant load tests of circumferentially notched round bar specimens of high strength steels after cyclic corrosion test and outdoor exposure have been performed to demonstrate that delayed fracture occurs when the hydrogen content from the environment, H_E, exceeds the critical hydrogen content for delayed fracture, H_C. During the constant load tests the humidity around the specimen was increased in stepwise manner to increase hydrogen entry. After fracture the specimen was kept at the humidity long enough to homogenize hydrogen in the specimen and to obtain more quantitative hydrogen content by thermal desorption analysis. H_E of the fractured specimens was higher than H_C, and H_E of the specimens not fractured was lower than H_C. This result confirms that the balance between H_C and H_E determines the occurrence of delayed fracture and that hydrogen-content-based evaluation of susceptibility to delayed fracture is reasonable. To certify the increase of H_E with increase in humidity, electrochemical hydrogen permeation test was carried out. The hydrogen permeation current density was increased especially at 98%RH. Enhancement of hydrogen entry with increase in CCT number was also shown by the test.     

Micrographic Digital Image Correlation Coupled with Microlithography: Case Study of Strain Localization and Subsequent Cracking at an FIB Notch Tip in a Laminated Ti-6Al-4V Alloy

This study presents a microlithography-based approach to increase the spatial resolution of strain mapping by micrographic digital image correlation. A micro-mesh with a lattice size of 500 nm was added on the surface of a Ti-6Al-4V alloy specimen with a coarse lath size of 1.1 μm. Although the micro-mesh pattern was not random, a combination of the laminated microstructure and the micro-mesh enabled sub-micrometer strain mapping through digital image correlation even for coarse lath larger than 1 μm. Specifically, the strain mapping technique used in this study was applied to characterize the strain component and distribution near an artificial sharp micro-stress concentration site introduced by a focused ion beam. The strain characterization under tensile deformation clarified that cracking occurred via shear strain localization at the micro-stress concentration site, indicating that accumulation of damage (such as vacancy or dislocation) plays an important role in the cracking mechanism of the Ti-6Al-4V alloy.     

High-resolution transmission electron microscopy study of crystallography and morphology of TiC precipitates in tempered steel

In spite of the significance of NaCl-type transition-metal carbides in steels, their crystallography and morphology have not been understood on an atomic scale. High-resolution electron microscopy was employed in the present work to examine the crystallography and morphology of TiC particles that precipitated in the quenched and tempered 0.05?wt%?C–0.20?wt%?Ti–2.0?wt%?Ni steel. Plate-like TiC precipitates with a thickness ranging from a couple of atomic layers to 20?nm were observed in steels by tempering at 550, 600 and 800°C. It was found that the Baker–Nutting orientation relationship is always satisfied with the ferrite matrix within about 5° for both the nanosized and the coarse TiC particles. The habit plane of the TiC precipitate is the (100) ferrite plane. A moderate tendency for the faceting of lateral interfaces on the {001} and {011} ferrite planes was found. The presence of interfacial misfit dislocations was revealed by examining the excess lattice fringes terminating at the interfaces between the TiC platelet and the ferrite matrix. The location and number of the excess lattice fringes terminating at the broad plane and the lateral interface were consistent with the mismatch in the atomic arrangement between the Baker–Nutting orientation relationship related TiC and ferrite.