Advances in rapid and effective break-in/conditioning/recovery of automotive PEMFC stacks

Automotive proton exchange membrane fuel cell stacks need to meet manufacturer specified rated beginning-of-life (BOL) performance before being assembled into vehicles and shipped off to customers. The process of “breaking-in” of a freshly assembled stack is often referred to as “conditioning.” It has become an intensely researched area especially in automotive companies, where imminent commercialization of fuel cell electric vehicles (FCEVs) demands a short, energy- and cost-efficient, and practical conditioning protocol. Significant advances in reducing the conditioning time from 1 to 2 days to as low as 4h or less, in some cases without the use of additional inert gases such as nitrogen, and with minimal use of hydrogen, and specialized test stations will be discussed.     

Divinylsiloxane‐bisbenzocyclobutene‐based polymer modified with polystyrene–polybutadiene–polystyrene triblock copolymers

Divinylsiloxane‐bisbenzocyclobutene (DVS‐bisBCB) polymer has very low dielectric constant and dissipation factor, good thermal stability, and high chemical resistance. The fracture toughness of the thermoset polymer is moderate due to its high crosslink density. A thermoplastic elastomer, polystyrene–polybutadiene–polystyrene triblock copolymer, was incorporated into the matrix to enhance its toughness. The cured thermoset matrix showed different morphology when the elastomer was added to the B‐staged prepolymer or when the elastomer was B‐staged with the DVS‐bisBCB monomer. Small and uniformly distributed elastomer domains were detected by transmission electron micrographs (TEM) in the former case, but TEM did not detect a separate domain in the latter case. A high percentage of the polystyrene–polybutadiene–polystyrene triblock copolymer could be incorporated into the DVS‐bisBCB thermoset matrix by B‐staging the triblock copolymer with the BCB monomer. The elastomer increased the fracture toughness of DVS‐bisBCB polymer as indicated by enhanced elongation at break and increased K1c values obtained by the modified edge‐lift‐off test. Elastomer modified DVS‐bisBCB maintained excellent electrical properties, high T_g and good thermal stability, but showed higher coefficient of linear thermal expansion values. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1591–1599, 2006     

Dilute sulfuric acid pretreatment of corn stover at high solids concentrations

Applied Biochemistry and Biotechnology - The enzymatic digestibility of a pretreated substrate is enhanced by increasing the severity of the pretreatment conditions, apparently because a greater...     

(1-Adamantanethio)pyridines and tetrahydropyridines from the reaction of 1-adamantanethiol with pyridine I-oxide in acetic anhydride

The reaction of pyridine 1-oxide with 1-adamantanethiol in acetic anhydride produced a mixture of 2- and 3-(1-adamantanethio)pyridines, 1-aeetyl-2-(1-adamantanethio)-3-hydroxy-4-acetoxy-1,2,3,4-telrahydropyridine and the corresponding 3-acetoxyderivative. Pure substances were separated by means of column chromatography on alumina. The tetrahydropyridines were identified by means of their proton magnetic and mass spectra. 4-(1-Adamantanethio)pyridine was synthesized from 4-chloropyridinc and 1-adamantanethiol. The three isomeric (1-adamantanethio)-pyridines were, each, cleaved by concentrated hydrochloric acid to give 1-chloroadamantane and the corresponding pyridinethiol.     

Method development for the quantitation of ABT-578 in rabbit artery tissue by 96-well liquid-liquid extraction and liquid chromatography/tandem mass spectrometric detection

Quantitative determination of drug concentrations in tissue samples can provide critical information for drug metabolism, kinetics, and toxicity evaluations. For analysis of tissue samples using liquid chromatography/tandem mass spectrometric (LC/MS/MS) detection, homogenization is a critical step in achieving good assay performance. Assay performance can be closely evaluated by spiking the drug directly into tissue samples prior to homogenization. It is especially important to include this assay evaluation for the analysis of artery tissue samples because artery tissue is very elastic, making it quite a challenge to develop an effective procedure for homogenization. An LC/MS/MS assay in 96-well format using liquid-liquid extraction was developed for analyzing ABT-578 in rabbit artery samples. Tissue quality control samples were prepared by spiking ABT-578 stock solutions directly into the tissue before homogenization. The usage of the tissue control samples gives a thorough evaluation of the sample preparation process that includes both homogenization and sample extraction. A 20% blood in saline solution was used as a homogenization solution. Calibration standards were made by spiking ABT-578 into rabbit whole blood. Blood quality control samples were also prepared by spiking ABT-578 into rabbit whole blood. These blood QC samples were used to confirm the validity of the calibration curve. A lower limit of quantitation of 0.050 ng/mL was achieved. The linear dynamic range of blood standards was from 0.050-30.3 ng/mL with the correlation coefficient (r) ranging from 0.9969-0.9996. Overall %CV was between 1.3 and 7.0%, and analytical recovery was between 98.2 and 105.8% for blood QC samples. The %CVs for tissue QC samples were between 6.7 and 13.0%, and analytical recovery after correction was between 93.5 and 114.3%.     

Tetronic acids and derivatives. Part XI . Structure of coupling products of tetronic acids with benzenediazonium sulfate

¹³C Nmr, ¹H nmr and ir parameters of coupling products of tetronic acids (4-hydroxy-5H-furan-2-ones) with benzene diazonium sulfate are only consistent with a phenylhydrazone formulation with an almost equal ratio of the syn and anti configurations. These results contrast with those of coupling products of acyclic 3-ketoesters, existing mainly as anti tautomers, and more sharply with the 3-parabromophenylhydrazone of L-dehydro ascorbic acid, which is exclusively syn.     

Chronocoulometric study of the electrochemistry of Prussian blue

During the electrochemical oxidation of Prussian blue (PB) to Prussian yellow (PY), an electrocatalytic oxygen production proceeds at the electrode when aqueous electrolyte solutions are used. The formed oxygen is scavenged by the PY, probably by absorption, and it is consumed during the electrochemical reduction of PY to PB by a heterogeneous chemical reaction of PB with oxygen to PY and hydrogen peroxide. Because of this catalytic regeneration of PY, it is impossible to determine the amount of low-spin iron by chronocoulometry using a potential program in which PB is first oxidized to PY and then the charge is measured to reduce PY to PB. The latter charge is biased by the electrocatalytic PY regeneration.     

Toward a microchip-based solid-phase extraction method for isolation of nucleic acids

A silica-based solid-phase extraction system suitable for incorporation into a microchip platform (nu-total analytical system; nu-TAS) would find utility in a variety of genetic analysis protocols, including DNA sequencing. The extraction procedure utilized is based on adsorption of the DNA onto bare silica. The procedure involves three steps: (i) DNA adsorption in the presence of a chaotropic salt, (ii) removal of contaminants with an alcohol/water solution, and (iii) elution of the adsorbed DNA in a small volume of buffer suitable for polymerase chain reaction (PCR) amplification. Multiple approaches for incorporation of this protocol into a microchip were examined with regard to extraction efficiency, reproducibility, stability, and the potential to provide PCR-amplifiable DNA. These included packing microchannels with silica beads only, generating a continuous silica network via sol-gel chemistry, and combinations of these. The optimal approach was found to involve immobilizing silica beads packed into the channel using a sol-gel network. This method allowed for successful extraction and elution of nanogram quantities of DNA in less than 25 min, with the DNA obtained in the elution buffer fraction. Evaluation of the eluted DNA indicated that it was of suitable quality for subsequent amplification by PCR.     

Evaluation of a complete HPLC solvent optimization system involving piece-wise quadratic modelling

Summary Interpretive methods are accepted to give the best possible results for selectivity optimization in HPLC. However the methods are very complex, and most work so far has been detailed academic studies. This paper describes an evaluation of a complete integrated system incorporating peak labelling, modelling of retention behaviour and calculation of response surfaces, with particular emphasis on the retention modelling. The peak labelling section has been discussed previously.A piece-wise quadratic function is investigated for the modelling of retention times across an isoeluotropic plane to effect selectivity optimization in HPLC. This requires 10 data-points on the isoeluotropic plane. The predicted global optimum and local optima are evaluated by comparison of calculated and experimental retention data, for a nine component sample. Seven interstitial points, distributed across the whole plane between the data-points, are similarly evaluated for a related sample. The typical error (in retention time) is less than 2%, often 1%, and the maximum error is 4.2%. At the global optimum the error was found be less than 1.3% for all 9 peaks.