Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Integral Representations,Differentiability Properties and Limits at Infinity for Beppo Levi Functions

The first aim in the present paper is to give an integral representation for Beppo Levi functions on R ⁿ. Our integral representation is an extension of Sobolev's integral representation given for infinitely differentiable functions with compact support. As applications, continuity and differentiability properties of Beppo Levi functions are studied.Our second aim in this paper is to study the existence of limits at infinity for Beppo Levi functions. We also consider the existence of fine-type limits at infinity with respect to Bessel capacities, which yields the radial limit result at infinity.     

Complex impedance spectra of chip inductor using Li–Zn–Cu–Mn ferrite

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li–Zn–Cu–Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni–Zn–Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li–Zn–Cu–Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li–Zn–Cu–Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li–Zn–Cu–Mn ferrite enabled us to easily design the complex impedance of MCI component.     

Hydrolysis of acetals in water under hydrothermal conditions

A simple method for the hydrolysis of acetals and ketals was accomplished in neutral water or aqueous media by hydrothermal treatment without using acidic reagents. The deacetalization reaction was effectively accelerated in the presence of calcium chloride. Because no acidic catalysts were employed, neutralization of the reaction mixture was not necessary after the reaction. This sequence was successfully applied to the hydrolysis of chitosan, a biodegradable polyaminosaccharide.     

Regularity of Harmonic Functions in Cheeger-Type Sobolev Spaces

We give a geometric approach to the study of the regularity of harmonic functions in Cheeger-type Sobolev spaces, and prove the Hölder continuity of such functions. In the proof, we give a definition of an upper curvature bound of the unit sphere of a Banach space, which seems to be of independent interest.     

Products, cones, and suspensions of spaces with the measure contraction property

This article concerns several geometric properties of metricmeasure spaces satisfying the measure contraction property (MCP),which can be considered as a generalized notion of lower Riccicurvature bounds. We prove that the MCP of spaces descends totheir products and Euclidean cones. We also show that a positivelycurved space in terms of the MCP with a maximal diameter canbe represented as the spherical suspension of some topologicalmeasure space.     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

Exiguolide, a new macrolide from the marine sponge Geodia exigua

A new 20-membered macrolide designated exiguolide has been isolated from the marine sponge Geodia exigua, and its structure determined by interpretation of spectroscopic data. Exiguolide specifically inhibited fertilization of sea urchin (Hemicentrotus pulcherrimus) gametes but not embryogenesis of the fertilized egg.     

Effect of Ru crystal orientation on the adhesion characteristics of Cu for ultra-large scale integration interconnects

The adhesion of Cu on Ru substrates with different crystal orientations was evaluated. The crystal orientation of sputter deposited Ru could be changed from (1 0 0) to (0 0 1) by annealing at 650 °C for 20 min. The adhesion of Cu was evaluated by the degree of Cu agglomeration on Ru. Cu films on annealed Ru films with the (0 0 1) crystal orientation showed 28% lower RMS values and 50% lower Ru surface coverage than Cu as-deposited on Ru having the (1 0 0) crystal orientation after annealing at 550 °C for 30 min, which suggest that Cu wettability on the Ru(0 0 1) was better than that on the Ru(1 0 0) plane. The low lattice misfit of 4% between Cu(1 1 1) and Ru(0 0 1) may be the reason for this good adhesion property.     

Phenomenon of labyrinth seal with low static pressure difference and large clearance

This paper discusses the straight-through type labyrinth seal. This labyrinth seal is used for axial flow fans, which h ave an outer ring at the blade tip to seal the clearance between the ring tip and the fan shroud, in order to prevent the reverse flow or leakage. These fans are used for the cooling of automobile radiators . In these cases, the labyrinth seal is used in an extremely low static pressure difference and a large clearance . A significant decrease of the leakage rate was reported even when the labyrinth seal rotated in comparatively low speed in this unique condition according to the authors’ former report. However, this phenomen on is differ ent from past research. Further more the cause of th is phenomenon has not been determined. Therefore, the internal flow was depicted with Computational Fluid Dynamics (CFD) in or der to clarify the ca use of this phenomenon. The results of CFD show that the leakage rate decreases significantly because the carry -over flow is intercepted in the expansion groove. This is the newly discovered phenomenon which occurs under the unique condition of an extremely low differential pressure. It has not been pointed out before as the reason why the rotation decreases the leakage rate.