Correction to: Practical framework for data-driven RANS modeling with data augmentation

Acta Mechanica Sinica -     

A New Sufficient Degree Condition for a Graphic Sequence to Be Forcibly k-Edge-Connected

A graphic sequence π =(d₁, d₂,..., d_n) is said to be forcibly k-edge-connected if every realization of π is k-edge-connected. In this paper, we obtain a new sufficient degree condition for π to be forcibly k-edgeconnected. We also show that this new sufficient degree condition implies a strongest monotone degree condition for π to be forcibly 2-edge-connected and a conjecture about a strongest monotone degree condition for π to be forcibly 3-edge-connected due to...     

A note on statistical analysis of factor models of high dimension

Science China Mathematics - Linear factor models are familiar tools used in many fields. Several pioneering literatures established foundational theoretical results of the quasi-maximum likelihood...     

利用沙漠沙低温合成高长径比莫来石晶须

利用沙漠沙独特的化学组成特性和矿物特性,将沙漠沙荒料作为硅源,工业Al(OH)3作为铝源制备莫来石晶须.改变硅源/铝源配比和合成温度,结合XRD、SEM、TEM研究莫来石生长环境和自由生长形态的变化.研究结果表明:当沙漠沙与Al(OH)3的质量比为35/65时,在1200℃的低温下就能获得平均值>60的高长径比莫来石晶须;随着煅烧温度的升高,莫来石晶须长径比不断增大,当温度升至1300℃,平均长径比>94.随着合成温度的升高,莫来石的形成经过了一次莫来石和二次莫来石化两个阶段;若配方中Al2 O3处于过饱和状态,样品中刚玉相会随着煅烧温度的升高出现先增多后降低的变化现象.     

Integral Representations of the Large and Little Schröder Numbers

In the paper, the authors establish several integral representations for the generating functions of the large and little Schröder numbers and for the large and little Schröder numbers.     

Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Synthesis of Small‐Sized,Porous, and Low‐Toxic Magnetite Nanoparticles by Thin POSS Silica Coating

In this communication, we report the synthesis of small‐sized (<10 nm), water‐soluble, magnetic nanoparticles (MNPs) coated with polyhedral oligomeric silsesquioxanes (POSS), which contain either polyethylene glycol (PEG) or octa(tetramethylammonium) (OctaTMA) as functional groups. The POSS‐coated MNPs exhibit superparamagnetic behavior with saturation magnetic moments (51–53 emu g^?1) comparable to silica‐coated MNPs. They also provide good colloidal stability at different pH and salt concentrations, and low cytotoxicity to MCF‐7 human breast epithelial cells. The relaxivity data and magnetic resonance (MR) phantom images demonstrate the potential application of these MNPs in bioimaging.     

A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.