Microwave‐assisted polycondensation of 4‐octylaniline with dibromoarylene

The Pd‐catalyzed polycondensation of 4‐octylaniline with various dibromoarylenes was carried out under microwave heating. Microwave heating led to a decrease in the reaction time and an increase in the molecular weight of the polymers as compared to conventional heating. Microwave heating also allowed the catalyst loading to be reduced to 1 mol %, yielding polymerization results that were comparable to those under conventional heating and 5 mol % catalyst. Investigations regarding field‐effect transistors and organic photovoltaic cells using the obtained poly(arylamine) with azobenzene units revealed that increasing the molecular weight of the polymer led to improved device performance, including hole mobility and power conversion efficiency. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 536–542     

A Hydroperoxide-Mediated Decarboxylation of α-Ketoacids Enables the Chemoselective Acylation of Amines

Strategies for the formation of amide bonds, that is, one of the most basic and important transformations in organic synthesis, have so far focused predominantly on dehydration reactions. Herein, we report and demonstrate the practical utility of a novel decarboxylative amidation of α-ketoacids by using inexpensive tert-butyl hydroperoxide (TBHP), which is characterized by high yields, a broad substrate scope, mild reaction conditions, and a unique chemoselectivity. These features enable the synthesis of peptides from amino acid derived α-ketoacids under preservation of the stereochemical information.     

Crosslinking network of bio‐based bis‐functional epoxides derived from trans‐limonene oxide

The thiol‐ene reaction between trans‐limonene oxide (trans‐LO) and ethane‐1,2‐dithiol in the presence of triethylborane affords a bio‐based bis‐functional epoxide (bis‐trans‐LO). The crosslinking reaction of bis‐trans‐LO with branched polyethyleneimine (BPEI; M_n = 600; BPEI₆₀₀) at a feed ratio of bis‐trans‐LO/BPEI₆₀₀ = 57/43 (wt/wt) yields the corresponding network polymer with T_d10 (10% thermal decomposition temperature) of 304.7 °C in 98% yield. In contrast, negligible amounts of network polymer are obtained by the reaction of bis‐LO (bis‐functional epoxide derived from cis and trans‐LO) and BPEI₆₀₀ regardless of the feed ratio. The mechanical strengths as measured by direct tensile tests of the network polymers derived from bis‐trans‐LO and BPEI_600,1800 (M_n = 600 and 1800) were approximately 16 and 11 times higher than that of bis‐LO and BPEI₁₈₀₀, respectively. The tensile shear strengths of the metal‐to‐metal adhesive bonds induced by bis‐trans‐LO and BPEI_600,1800 were 9.5 and 14.1 MPa, respectively. DMA revealed that the storage modulus of the network polymer derived from bis‐trans‐LO and BPEI₁₈₀₀ in the rubber region was higher than that of the material prepared from bis‐LO and BPEI₁₈₀₀, indicating higher crosslink density of the bis‐trans‐LO/BPEI₁₈₀₀ system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2466–2473     

Silicon-Based Integrated Optic Pressure Sensor Using Intermodal Interference between TM-Like and TE-Like Modes

In this paper, a silicon-based integrated optic pressure sensor using an intermodal interference between the fundamental TM-like and TE-like modes is described. The sensor consists of a micromachined rectangular diaphragm and a straight polystyrene optical waveguide passing over the diaphragm. Its sensitivity is theoretically known to be strongly dependent on the position of the waveguide over the diaphragm. To experimentally investigate such dependence, we fabricated a sensor with a 1.2 mm ×10 mm ×20 μm diaphragm, over which waveguides were placed at 50 μm intervals. The measured phase sensitivity was 98 mrad/kPa for the waveguide nearest to the diaphragm edge. The measurement was also carried out for the other waveguides. As theoretically expected, the largest sensitivity was obtained for the waveguide nearest to the edge.     

Light Diffraction of Aligned Polymer Fibers Periodically Dispersed by Phase Separation of Liquid Crystal and Polymer

We have confirmed light diffraction of aligned polymer fibers obtained by a phase separation of an anisotropic-phase solution of liquid crystal and polymer. He—Ne laser light passing through the polymer fibers was scattered in the axis vertical to the fibers, and had two peaks of light intensity symmetrical to the center of the transmitting laser spot. The two peaks were found to be caused by light diffraction due to the periodic polymer-fiber dispersion because the peaks corresponded to values calculated by intervals between the fibers. The periodical fiber networks are considered to be formed by anisotropic spinodal decomposition. This effect can be used to measure the dispersion order of the polymer fibers. © 2004 The Optical Society of Japan     

Facilitated sulfate transfer across the nitrobenzene-water interface as mediated by hydrogen-bonding ionophores.

Facilitated SO4(2-) transfers by hydrogen bond-forming ionophores are investigated across the nitrobenzene (NB)-water interface by using polarography with a dropping electrolyte electrode. Bis-thiourea 1, alpha,alpha'-bis(N'-p-nitrophenylthioureylene)-m-xylene, is found to significantly facilitate the transfer of the highly hydrophilic SO4(2-) whereas its counterpart, N-(p-nitrophenyl)-N'-propylthiourea (ionophore 2), cannot. In contrast to the predominant formation of a 1:1 complex with SO4(2-) in the bulk NB phase, the SO4(2-) transfer assisted by 1 is indeed based on the formation of a 1:2 complex between SO4(2-) and ionophore, even under the condition of [SO4(2-)]aq > [1]org. Such an exclusive formation of the 1:2 (SO4(2-) to ionophore) complex at the NB-water interface is not observed with structurally similar bis-thiourea 3, alpha,alpha'-bis(N'-phenylthioureylene)-m-xylene, where p-nitrophenyl moietes of bis-thiourea 1 are simply replaced by phenyl groups. The facilitated transfer of SO4(2-) with bis-thiourea 1 is further compared to that of HPO4(2-) and H2PO4- across the NB-water interface, which was previously shown to be assisted by 1 through the formation of the 1:1 and 2:1 (anion to ionophore) complexes, respectively. On the basis of these examinations, unique binding behaviors of hydrogen bond-forming ionophores at the NB-water interface are discussed, with a view towards development of ionophore-based anion-selective chemical sensors.     

Multimode optical fiber demultiplexer-star coupler using a single gradient-index-rod lens and a multi-facet grating

An optical fiber multi-function device consisting of a single gradient-index-rod lens and a multi-facet blazed reflection grating is proposed to simultaneously realize functions of wavelength demultiplexing and optical signal distribution in a multimode optical fiber transmission system. We analyzed the demultiplexing characteristics and the tolerance of optical components using the ray trace method. This device can realize not only low loss optical signal distribution but also offers improved demultiplexing characteristics in comparison with the previously proposed demultiplexer-multiposition switch. The following characteristics are expected from the design using commercially available optical components: a working band of 0.64–0.88 μm, channel separation of 34–36 nm, 3 dB bandwidth of 27–28 nm, channel cross-talk of less than - 40 dB and minimum excess insertion loss of 0.9–2.1 dB.