Cobalt promoted Ni/MgAl2O4 catalyst in lean methane catalytic oxidation

In the present research, magnesium aluminate spinel was prepared as catalyst support using a novel, facile, and efficient mechanochemical method. The Co-promoted catalysts with 20 wt.% of Ni were fabricated using an impregnation route and the samples were analyzed by the X-ray diffraction (XRD), N₂ adsorption/desorption (BET), temperature-programmed reduction and desorption (H₂-TPR and O₂-TPD), and field emission scanning electron microscopy (FESEM) tests. The results confirmed that all samples have a mesoporous structure with a high specific surface area and the presence of cobalt caused complete CH₄ oxidation at low temperatures, and no side reactions were observed. The results indicated that the 3%Co-20%Ni/MgAl₂O₄ catalyst was the optimal sample among the prepared catalysts, owing to the improvement of reduction features and oxygen mobility. The 50 and 90% of methane conversion was obtained at 530 and 600 °C, respectively. Also, the influence of calcination temperature, GHSV, and feed ratio was determined on the catalytic activity. The obtained outcomes revealed that the calcination temperature has a significant effect on the textural properties and catalytic efficiency. The sample calcined at 700 °C showed the weakest performance, which was related to the sintering of particles at high temperatures. The catalytic stability showed that the 3%Co-20%Ni/MgAl₂O₄ has acceptable stability during 600 min time of reaction.

Graphical abstract

     

Development of the ANN–KIM composed model to predict the nanofluid energetic thermal conductivity via various types of nano-powders dispersed in oil

Journal of Thermal Analysis and Calorimetry - Artificial neural network/kriging interpolation method optimization method which is evaluated concerned the hybrid nanofluid composed of iron oxide...     

Thermodynamic properties of transition metals in aqueous solution. 2. The enthalpies of mixing of aqueous solutions of CoCl2, CuCl2, and MnCl2 with NaCl at varying ionic strength at 25°C

Enthalpies of mixing (_m H) aqueous solutions of CoCl₂, CuCl₂, and MnCl₂ with NaCl solutions were measured at constant ionic strengths of 0.5, 1.0, and 3.0 molal at 25°C. The excess enthalpy equations of Pitzer were then fit to the resulting _m H data. The resulting parameters are the temperature derivatives of the activity coefficient mixing parameters in the Pitzer system. The heat of mixing data for CoCl₂ and CuCl₂ were in agreement with earlier isomolal results by other workers.     

The effect of the physical and chemical characteristics of activated carbons on the adsorption energy and affinity coefficient of Dubinin equation

The dependency of adsorption energy (E) and affinity coefficient (beta) of Dubinin equations (Dubinin-Radushkevich (DR) or Dubinin-Astakhov (DA)) on surface chemistry and porosity of activated carbons was investigated by analyzing adsorption of nitrogen, benzene, trichloroethylene (TCE), and water vapor by several surface-modified activated carbons and carbon fibers. For all studied nonpolar adsorbates, carbons with smaller average micropores showed higher adsorption energies independent of their surface chemistry. For water vapor, carbons with higher surface polarities showed higher adsorption energies due to specific adsorbate-adsorbent interactions. Adsorption energies increased with decreasing average micropore widths. betaN2,DR for different carbons were observed to vary in the 0.292-0.539 range. Carbons with higher degrees of mesoporosity had higher betaN2,DR values, while no dependency was observed between betaN2,DR and surface chemistry. A comparison of DR and DA cases indicates that: (1) the average value of betaN2,DA is considerably above the classical value of this parameter; and (2) the range of betaN2,DA values were smaller compared to betaN2,DR, despite a wide range of mesoporosity of carbons examined. Obtained beta(TCE,DR) values varied in the 0.952-1.243 range, with an average value of 1.085+/-0.083, independent of surface chemistry or porosity of activated carbons. A similar result was observed for beta(TCE,DA). betaH2O,DR values of different granular and fibrous activated carbons changed in the range of 0.081-0.271. They depended more on the carbon surface chemistry and less on the porosity. A similar result was obtained when DA equation was considered.     

Joule-Thomson inversion curve prediction by using equation of state

In this paper five equations of state are tested for checking their ability to predict the Joule-Thomson inversion curve.These five equations of state are:Mohsennia-Modarres-Mansoori(MMM),Ji-Lemp(JL),modified Soave-Redlich-Kwang(SRK)equation of state by Graboski(MSRK1),modified SRK equation of state by Peneloux and Rauzy(MSRK2),and modified Peng-Robinson (PR)equation of state by Rauzy(PRmr).The investigated equations of state give good prediction of the low-temperature branch of the inversion curve,except for MMM equation of state.The high-temperature branch and the peak of the inversion curve have been observed,in general,to be sensitive to the applied equation of state.The values of the maximum inversion temperature and maximum inversion pressure are calculated for each component used in this work.     

Modification of the resistance of two epoxy resins to accelerated weathering using calcium sulfate as a photostabilizer

Epoxy-timber composites have received increasing attention during the last decades because there are many advantages related to their uses as construction materials in applications such as timber bridges. However, the durability of epoxy-timber composites under outdoor conditions has become a concern for many epoxy resins. This study evaluated the chemical, thermal, and mechanical properties of two cured epoxies, the product of the diglycidyl ether of bisphenol A with 2,4-trimethyl-1,6-hexanediamine (DGEBA-TMDA) and the analogous resin prepared with the hydrogenated diglycidyl ether of bisphenol A (HDGEBA-TMDA), each mixed with 2?wt. % calcium sulfate (CS). We hypothesized that the use of CS, as an inorganic UV absorber, could decrease undesirable effects arising from exposure to UV light, moisture, and extreme temperatures.

An accelerated aging chamber simulated natural weathering for 1, 2, 3, 4, and 6?months. Chemical changes in cured epoxy systems over time in the presence and absence of CS fillers were determined using Fourier transform infrared spectroscopy (FT-IR). Thermal degradation profiles before and after exposure to accelerated weathering were followed by thermogravimetric analysis (TGA). The glass transition temperatures (T_g) before and after accelerated weathering were measured, and the effect of accelerated weathering on the surface morphology of the epoxy systems was investigated by scanning electron microscopy (SEM). In the presence of CS, after 6?months accelerated weathering the tensile strength of DGEBA-TMDA reduced by 23.8?±?2.4%, compared to 46.5?±?5.5% in its absence, while the corresponding values for HDGEBA-TMDA were 21.4?±?2.1% and 28.7?±?1.8%.     

Synthesis and Evaluation of Biocompatible pH‐Sensitive Hydrogels as Colon‐Specific Drug Delivery Systems

Because of the growing importance of pH‐sensitive hydrogels as drug delivery systems, biocompatible copolymeric hydrogels based N‐vinyl‐2‐pyrrolidinone (NVP) and methacrylic acid (MAA) were designed and synthesized. These hydrogels were investigated for oral drug delivery. Radical copolymerizations of N‐vinyl‐2‐pyrrolidinone (NVP) and methacrylic acid (MAA) with the various ratios of cross‐linking agent were carried out at 70 °C. Azabisisobutyronitrile (AIBN) was the free‐radical initiator employed and Cubane‐1,4‐dicarboxylic acid (CDA) linked to two 2‐hydroxyethyl methacrylate (HEMA) group was the crosslinking agent (CA) used for hydrogel preparations. The hydrogels were characterized by differential scanning calorimetry and FT‐IR. Equilibrium swelling studies were carried out in enzyme‐free simulated gastric and intestinal fluids (SGF and SIF, respectively). A model drug, olsalazine [3,3′‐azobis (6‐hydroxy benzoic acid)] (OSZ) as an azo derivative of 5‐aminosalicylic acid (5‐ASA), was entrapped in these gels and the in‐vitro release profiles were established separately in both enzyme‐free SGF and SIF. The drug‐release profiles indicated that the amount of drug released depended on the degree of swelling. The swelling was modulated by the amount of crosslinking of the polymer bonded drug (PBDs) prepared. Based on the great difference in hydrolysis rates at pH 1 and 7.4, these pH‐sensitive hydrogels appear to be good candidates for colon‐specific drug delivery.