DFT study of carbon monoxide adsorption on α-Al2O3(0001)

The adsorption of CO on α-Al₂O₃(0001) was studied using the DFT-GGA computational method and on α-Al₂O₃ powder experimentally by Infra red spectroscopy. The core and valence level regions of α-Al₂O₃(0001) single crystal surface were also studied experimentally. Ar ions sputtering of the surface results in a slight but reproducible decrease in the XPS O2p lines in the valence band regions due to preferential removal of surface (and near surface) O atoms. Core level XPS O1s and Al2p further confirmed oxygen depletion with an associated surface stoichiometry close to Al₂O_2.9. The adsorption energy of CO was computed and found equal to 0.52 eV for θ = 0.25, it decreased to 0.42 eV at θ = 1. The IR frequency of νCO was also computed and in all cases it was blue shifted with respect to gas phase CO. The shift, Δν, decreased with increasing coverage where it was found equal to 56 cm^? 1 for θ = 0.25 and decreased to 30 cm^? 1 for θ = 1. Structural analyses indicated that the change in the adsorption energy and the associated frequency shift is due to surface relaxation upon adsorption. Experimentally the adsorption of CO gave rise to one main IR peak at 2154 cm^? 1 at 0.3 Torr and above. Two far smaller peaks are also seen at lower pressures of 0.03–0.2 Torr at 2189 and 2178 cm^? 1. The isosteric heat of adsorption was computed for the IR band at 2154 cm^? 1 and was found equal to 0.2 eV which did not change with coverage in the investigated range up to θ = 0.6.     

Sputtered deposited nanocrystalline ZnO films: A correlation between electrical, optical and microstructural properties

Zinc oxide thin films were prepared by dc (direct current) and rf (radio frequency) magnetron sputtering on glass substrates. ZnO films produced by dc sputtering have a high resistance, while the films produced using rf sputtering are significantly more conductive. While the conductive films have a compact nodular surface morphology, the resistive films have a relatively porous surface with columnar structures in cross section. Compared to the dc sputtered films, rf sputtered films have a microstructure with smaller d spacing, lower internal stress, higher band gap energy and higher density. Dependence of conductivity on the deposition technique and the resulting d spacing , stress, density, band gap, film thickness and Al doping are discussed. Correlations between the electrical conductivity, microstructural parameters and optical properties of the films have been made. PACS 73.25.+i; 81.15.cd; 81.05.ys     

Facile synthesis of platinum nanoparticle-containing porous carbons,and their application to amperometric glucose biosensing

This study describes the facile synthesis of platinum nanoparticle-containing porous carbons (Pt/C) by carbonization of freeze-dried agarose gels containing potassium tetrachloroplatinate under a nitrogen atmosphere at 800 °C. By adjusting the ratio between agarose and platinate in the freeze-dried gels, the Pt content in the final Pt/C products could be systematically varied from 0–10 wt.%. Transmission electron microscopy, inductively coupled plasma atomic emission spectrometry, X-ray photoelectron spectroscopy, Raman spectroscopy, and nitrogen physisorption measurements revealed that the Pt/C materials obtained by this method possess high surface areas (350–500 m² g⁻¹), narrow Pt nanoparticle size distributions (6 ± 3 nm) and nanocrystalline graphite –like carbon character. By immobilization of glucose oxidase on the surface of a 4 wt.% Pt/C electrocatalyst prepared by this route, a very sensitive amperometric glucose biosensor was obtained (response time <2 min, sensitivity 1.9 mA M⁻¹; and a linear response with glucose concentration up to 10 mM). The simplicity and versatility of the described synthetic method suggests its application to the preparation of carbon supported noble metal catalysts including palladium/C and gold/C.

This study describes the facile synthesis of platinum nanoparticle-containing porous carbons (Pt/C) by carbonization of freeze-dried agarose gels containing potassium tetrachloroplatinate. The Pt/C materials exhibited excellent electrocatalytic activities, as demonstrated by their successful integration into amperometric glucose biosensor

     

Ethanol photo-oxidation on a rutile TiO2(110) single crystal surface

The reaction of ethanol has been studied on the surface of rutile TiO(2)(110) by Temperature Programmed Desorption (TPD), online mass spectrometry under UV excitation and photoelectron spectroscopy while the adsorption energies of the molecular and dissociative modes of ethanol were computed using the DFT/GGA method. The most stable configuration is the dissociative adsorption in line with experimental results at room temperature. At 0.5 ML coverage the adsorption energy was found equal to 80 kJ mol(-1) for the dissociative mode (ethoxide, CH(3)CH(2)O(a) + H(a)) followed by the molecular mode (67 kJ mol(-1)). The orientation of the ethoxides along the [001] or [110] direction had minor effect on the adsorption energy although affected differently the Ti and O surface atomic positions. TPD after ethanol adsorption at 300 K indicated two main reactions: dehydration to ethylene and dehydrogenation to acetaldehyde. Pre-dosing the surface with ethanol at 300 K followed by exposure to UV resulted in the formation of acetaldehyde and hydrogen. The amount of acetaldehyde could be directly linked to the presence of gas phase O(2) in the vacuum chamber. The order of this photo-catalytic reaction with respect to O(2) was found to be 0.5. Part of acetaldehyde further reacted with O(2) under UV excitation to give surface acetate species. Because the rate of photo-oxidation of acetates (acetic acid) was slower than that of ethoxides (ethanol), the surface ended up by being covered with large amounts of acetates. A reaction mechanism for acetaldehyde, hydrogen and acetate formation under UV excitation is proposed.     

Phase-oriented surface segregation in an aluminium casting alloy

There have been many reports of the surface segregation of minor elements, especially Mg, into surface layers and oxide films on the surface of Al alloys. LM6 casting alloy (Al-12%Si) represents a challenging system to examine such segregation as the alloy features a particularly inhomogeneous phase structure. The very low but mobile Mg content (approximately 0.001 wt.%), and the surface segregation of modifiers such as Na, mean the surface composition responds in a complex manner to thermal treatment conditions. X-ray photoelectron spectroscopy (XPS) has been used to determine the distribution of these elements within the oxide film. Further investigation by dynamic secondary ion mass spectrometry (DSIMS) confirmed a strong alignment of segregated Na and Mg into distinct phases of the structure.     

Simple Zeros of the Riemann Zeta-Function

Assuming the Riemann Hypothesis, Montgomery showed by meansof his pair correlation method that at least two-thirds of thezeros of Riemann's zeta-function are simple. Later he and Taylorimproved this to 67.25 percent and, more recently, Cheer andGoldston increased the percentage to 67.2753. Here we proveby a new method that if the Riemann and Generalized LindelöofHypotheses hold, then at least 70.3704 percent of the zerosare simple and at least 84.5679 percent are distinct. Our methoduses mean value estimates for various functions defined by Dirichletseries sampled at the zeros of the Riemann zeta-function. 1991Mathematics Subject Classification: 11M26.     

Existence and Uniqueness of Fixed Points for Markov Operators and Markov Processes

This paper concerns a Markov operator T on a space L₁, and aMarkov process P which defines a Markov operator on a spaceM of finite signed measures. For T, the paper presents necessaryand sufficient conditions for:

a the existence of invariant probabilitydensities (IPDs)

b the existence of strictly positive IPDs,and

c the existence and uniqueness of IPDs.

Similar resultson invariant probability measures for P are presented. The basicapproach is to pose a fixed-point problem as the problem ofsolving a certain linear equation in a suitable Banach space,and then obtain necessary and sufficient conditions for thisequation to have a solution. 1991 Mathematics Subject Classification:60J05, 47B65, 47N30.