喷流冷却复合陶瓷薄片激光器的热特性仿真分析及实验研究

为分析喷流冷却复合陶瓷薄片激光器的热特性,设计用于冷却复合陶瓷薄片的喷流冷却系统.利用湍流换热理论和计算流体动力学仿真方法建立喷流冷却复合陶瓷薄片激光器的流固耦合热仿真模型,定义评价其冷却能力和冷却均匀性的定量参数.根据该仿真模型得到喷流冷却系统的最优设计参数,并进行实验验证.使用163孔喷板,流量为0.2kg/s,入口温度为20℃,在1200 W泵浦时获得359 W激光输出功率,并测得复合陶瓷薄片上表面的最高温度为92℃.激光输出功率与复合陶瓷薄片上表面温度均与泵浦功率呈近似正线性关系,且温度的实验值与仿真值相符度较高.     

Influences of Sr2+ Doping on Microstructure,Giant Dielectric Behavior,and Non-Ohmic Properties of CaCu3Ti4O12/CaTiO3 Ceramic Composites

The microstructure, dielectric response, and nonlinear current-voltage properties of Sr²⁺-doped CaCu₃Ti₄O₁₂/CaTiO₃ (CCTO/CTO) ceramic composites, which were prepared by a solid-state reaction method using a single step from the starting nominal composition of CCTO/CTO/xSrO, were investigated. The CCTO and CTO phases were detected in the X-ray diffraction patterns. The lattice parameter increased with increasing Sr²⁺ doping concentration. The phase compositions of CCTO and CTO were confirmed by energy-dispersive X-ray spectroscopy with elemental mapping in the sintered ceramics. It can be confirmed that most of the Sr²⁺ ions substituted into the CTO phase, while some minor portion substituted into the CCTO phase. Furthermore, small segregation of Cu-rich was observed along the grain boundaries. The dielectric permittivity of the CCTO/CTO composite slightly decreased by doping with Sr²⁺, while the loss tangent was greatly reduced. Furthermore, the dielectric properties in a high-temperature range of the Sr²⁺-doped CCTO/CTO ceramic composites can be improved. Interestingly, the nonlinear electrical properties of the Sr²⁺-doped CCTO/CTO ceramic composites were significantly enhanced. The improved dielectric and nonlinear electrical properties of the Sr²⁺-doped CCTO/CTO ceramic composites were explained by the enhancement of the electrical properties of the internal interfaces.     

Radiative heat transfer augmentation of natural gas flames in radiant tube burners with porous ceramic inserts

Experiments were conducted using porous ceramic inserts to enhance the radiative heat transfer from natural gas flames in a straight-through radiant tube burner. The performance of the radiant tube burner with partially stabilized zirconia and silicon carbide inserts is compared to a baseline case of no inserts at three levels of combustion air preheat. Spectral intensities, temperatures within the radiant tube burner, tube wall temperatures, and exhaust temperatures were measured to determine the effectiveness of the enhanced heat transfer due to the inserts. Exhaust emission constituents were also measured to determine the effect that the inserts have on exhaust products. NO_x emissions are reduced by up to 30% with the inserts. The silicon carbide inserts have higher spectral intensities and total radiative energy transfer than partially stabilized zirconia inserts. Both inserts have enhanced radiant heat transfer compared to the no-insert configuration, with the radiative enhancement due to inserts as great as five times that of the no-insert configuration. The net result is increased tube wall temperatures and decreased exhaust temperatures with the ceramic inserts.     

TiB2增强Al2O3陶瓷刀具高速干切削摩擦磨损性能

采用TiB2增强Al2O3陶瓷刀具对淬硬钢进行高速干切削试验,利用切削高温作用下的摩擦化学反应,在刀具表面原位生成具有润滑作用的反应膜,从而实现Al2O3/TiB2陶瓷刀具的自润滑.结果表明:低速干切削时,Al2O3/TiB2陶瓷刀具的磨损机制主要表现为粘着磨损和磨料磨损;而在高速干切削时,刀具的磨损机制主要表现为氧化磨损,刀具表面经由氧化反应生成具有润滑作用的反应膜而起到固体润滑作用,从而使刀具的耐磨性能提高,随着TiB2含量和切削速度的增加,反应膜的减摩抗磨作用增强;而在切削区通入氮气时,由于刀具表面氧化膜形成受阻,刀具的抗磨能力有所降低.     

Micromechanics of residual stress and texture development due to poling in polycrystalline ferroelectric ceramics

This paper presents micromechanics based analysis of elastic strain and changes in the texture of poled polycrystalline ferroelectric PZT ceramics for direct comparison with synchrotron X-ray measurements. The grains are modelled as spherical inclusions, to which transformation strains are assigned depending on the fractions of different ferroelectric domains. Eshelby's inclusion problem with the classical self-consistent method is applied to evaluate the elastic state of the grains. In particular, the elongation due to lattice elastic strain is calculated as a function of inclination Ψ relative to the polar axis. The ratio of diffraction peak intensities, corresponding to the domain fractions, is also expressed as a function of Ψ. This analysis identifies the special character of the reflection, for which the lattice strain along in the stress free state is independent of ferroelectric domain population and hence unaffected by poling. The elongation due to the lattice strain parallel to and peak intensity ratio are expressed in terms of the overall macroscopic strain of a poled specimen, each having a dependence.     

Al_2O_3 基陶瓷摩阻材料的摩擦磨损特性

在ＭＧ－２００磨损试验机上，对以Ａｌ２Ｏ３为基体，分别添加固体润滑剂组元石墨和氮化硼制备的２种陶瓷摩阻材料的摩擦磨损特性进行了试验研究．结果表明：在给定的试验条件下，添加石墨或氮化硼都可以改善材料摩擦性能的稳定性；分别在１００℃，２００℃，３００℃和４００℃下定温试验时，这２种摩阻材料都具有较高的摩擦因数和良好的耐磨性，其中含氮化硼之摩阻材料的耐磨性比含石墨之摩阻材料的更好，前者在４００℃时的磨损率仅为后者在同温时的１／２．     

A NEW METHOD TO DETERMINE THE R-CURVE OF CERAMICS-FRACTURE GRATING METHOD

The etching technique of the single-lined zero-thickness specimen grating is applied tothe surface of the SiC fiber toughening Si_3N_4 ceramic composite specimen.The position of the crackand the crack length during the process of crack extension when the load is applied and gradually in-creased can be determined by recording the output voltage value of the Wheatstone bridge in which theceramic specimen with the fracture grating on is located.The crack-growth-resistance(R-curve) of thismaterialis thus obtained.     

载荷对Al2O3增强Y-TZP陶瓷磨损特性的影响

采用往复式摩擦磨损试验机研究了10%(质量分数计)Al2O3增强四方氧化锆多晶Y-TZP陶瓷材料(简称10ADZ)在不同载荷下的磨损行为与机制.结果表明:随着载荷的增加和滑动时间的延长,10ADZ陶瓷的磨损率增大,但并非呈线性增加,磨损率增长幅度不同;在62 N低载荷条件下,10ADZ陶瓷的磨损机制以犁沟和塑性变形为主;在124 N载荷下其主要的磨损形式为塑性变形、微切削和微断裂;而在310 N的高载荷下其主要的磨损机制为断裂磨损.     

陶瓷人工关节的跑合和摩擦性能研究

研究３种生物陶瓷材料（氧化铝，氮化硅和碳化硅）在水中的跑合及其摩擦特性。结果表明：跑合前，氮化硅－氮化硅摩擦副的起始摩擦因数和稳态摩擦因数最高，碳化硅－碳化硅磨擦副的起始摩擦因数和稳态摩擦因数最低，跑合后，氧化铝－氧化铝摩擦副的稳态摩擦因数最高，碳化硅－碳化硅摩擦副的起始摩擦因数和稳态摩擦因数仍然最低。当摩擦副表面均加工到超光洁状态（表面粗糙度Ｒａ为纳米数量级）时，碳化硅－碳化硅摩擦副的摩擦性能最     

氮化硅陶瓷平板振动模态参数的研究

本文采用压电陶瓷片测振技术,试验分析了氮化硅陶瓷平板的固有频率及模态阻尼比,试验结果与有限元计算结果比较吻合。本文还对氮化硅陶瓷平板与普通钢平板做了对比试验,结果表明氮化硅陶瓷平板的固有频率及模态阻尼比都较高。