双激光脉冲打靶形成Gd等离子体的极紫外光谱辐射

高端芯片制造所需要的极紫外光刻技术位于我国当前面临35项"卡脖子"关键核心技术之首.高转换效率的极紫外光源是极紫外光刻系统的重要组成部分.本文通过采用双激光脉冲打靶技术实现较强的6.7 nm极紫外光输出.首先,理论计算Gd¹⁸⁺—Gd²⁷⁺离子最外层4d壳层的4p-4d和4d-4f能级之间跃迁、以及Gd¹⁴⁺—Gd¹⁷⁺离子最外层4f壳层的4d-4f能级之间跃迁对波长为6.7 nm附近极紫外光的贡献.其后开展实验研究,结果表明,随着双脉冲之间延时的逐渐增加,波长为6.7 nm附近的极紫外光辐射强度呈现先减弱、后增加、之后再减弱的变化趋势,在双脉冲延时为100 ns处产生的极紫外光辐射最强.并且,在延时为100 ns处产生的光谱效率最高,相比于单脉冲激光产生的光谱效率提升了33%.此外,发现双激光脉冲打靶技术可以有效地减弱等离子体的自吸收效应,获得的6.7 nm附近极紫外光谱宽度均小于单激光脉冲打靶的情形,且在脉冲延时为30 ns时刻所产生的光谱宽度最窄,约为单独主脉冲产生极紫外光谱宽度的1/3.同时...     

一种通过梯形PPMgLN波导倍频实现带宽可调谐光源的理论研究

本文设计了一种梯形的周期极化掺镁铌酸锂(PPMgLN)波导,并通过在传播方向上引入温度梯度来拓宽其倍频(SHG)过程的泵浦光源可接收带宽。通过有限差分的光束传输法,计算波导的有效折射率,并进行波导尺寸的设计。结果表明,通过改变梯形波导不同位置的温度,使其形成一个温度梯度,可拓宽泵浦光源的波长可接收带宽。本文所设计的PPMgLN波导最大泵浦光源可接收带宽为C波段,即1 530~1 565 nm,该波导可倍频C波段,得到输出波段带宽为765~782.5 nm,温度调谐范围为30~150 ℃。     

石墨烯负载的氧配位钴单原子稳定金属锂负极

Lithium (Li)-based batteries are the dominant energy source for consumer electronics, grid storage, and electrified transportation. However, the development of batteries based on graphite anodes is hindered by their limited energy density. With its ultrahigh theoretical capacity (3860 mAh∙g⁻¹), low redox potential (−3.04 V), and satisfactorily low density (0.54 g∙cm⁻³), Li metal is the most promising anode for next-generation high-energy-density batteries. Unfortunately, the limited cycling life and safety issues raised by dendrite growth, unstable solid electrolyte interphase, and "dead Li" have inhibited their practical use. An effective strategy is to develop a suitable lithiophilic matrix for regulating initial Li nucleation behavior and controlling subsequent Li growth. Herein, single-atom cobalt coordinated to oxygen sites on graphene (Co-O-G SA) is demonstrated as a Li plating substrate to efficiently regulate Li metal nucleation and growth. Owing to its dense and more uniform lithiophilic sites than single-atom cobalt coordinated to nitrogen sites on graphene (Co-N-G SA), high electronic conductivity, and high specific surface area (519 m²∙g⁻¹), Co-O-G SA could significantly reduce the local current density and promote the reversibility of Li plating and stripping. As a result, the Co-O-G SA based Li anodes exhibited a high Coulombic efficiency of 99.9% at a current density of 1 mA∙cm⁻² with a capacity of 1 mAh∙cm⁻², and excellent rate capability (high current density of 8 mA∙cm⁻²). Even at a high plating capacity of 6 mAh∙cm⁻², the Co-O-G SA electrode could stably cycle for an ultralong lifespan of 1300 h. In the symmetric battery, the Co-O-G SA based Li anode (Co-O-G SA/Li) possessed a stable voltage profile of 18 mV for 780 h at 1 mA∙cm⁻², and even at a high current density of 3 mA∙cm⁻², its overpotential maintained a small hysteresis of approximately 24 mV for > 550 h. Density functional theory calculations showed that the surface of Co-O-G SA had a stronger interaction with Li atoms with a larger binding energy, −3.1 eV, than that of Co-N-G SA (−2.5 eV), leading to a uniform distribution of metallic Li on the Co-O-G SA surface. More importantly, when matched with a sulfur cathode, the resulting Co-O-G SA/lithium sulfur full batteries exhibited a high capacity of 1002 mAh∙g⁻¹, improved kinetics with a small polarization of 191 mV, and an ultralow capacity decay rate of 0.036% per cycle for 1000 cycles at 0.5C (1C = 1675 mA∙g⁻¹) with a steady Coulombic efficiency of nearly 100%. Therefore, this work provides novel insights into the coordination environment of single atoms for the chemistry of Li metal anodes for high-energy-density batteries.     

Low-cost automated capillary electrophoresis instrument assembled from commercially available parts

A CE instrument that can be assembled from commercially available components with minimal construction effort is described. Except for the electronic control circuitry no specially made parts are required. It is based on a flexible design of microfluidic, electropneumatic, and electronic sections and different configurations can easily be implemented. Automated injection into the capillary is performed hydrodynamically by the application of a pressure for a controlled length of time. The performance of the device was tested with a contactless conductivity detector by separating different metal ions. In addition, nine metal cations related to the quality of honey were separated in 2.3 min and four honey samples were analysed quantitatively to demonstrate the applicability of the method.     

Growth and characterization of two-dimensional crystals for communication and energy applications

This review article covers the growth and characterization of two-dimensional (2D) crystals of transition metal chalcogenides, h-BN, graphene, etc. The chemical vapor transport method for bulk single crystal growth is discussed in detail. Top-down methods like mechanical and liquid exfoliation and bottom-up methods like chemical vapor deposition and molecular beam epitaxy for mono/few-layer growth are described. The optimal characterization techniques such as optical, atomic force, scanning electron, and Raman spectroscopy for identification of mono/few-layer(s) of the 2D crystals are discussed. In addition, a survey was done for the application of 2D crystals for both creation and deterministic transfer of single-photon sources and photovoltaic systems. Finally, the application of plasmonic nanoantenna was proposed for enhanced solar-to-electrical energy conversion and faster/brighter quantum communication devices.     

2-Isopropylbenzimidazole and 2-methylbenzimidazole as bulky proton sources: Stereoselective protonation and application to the synthesis of γ- and δ-lactones

2-Isopropylbenzimidazole and 2-methylbenzimidazole have been found to be effective bulky proton sources for stereoselective protonation of chiral enolate anions. 2-Isopropylbenzimidazole worked in the stereoselective protonation of the Birch reduction of chiral α,β-unsaturated imides. On the other hand, 2-methylbenzimidazole was found to be the best protonation reagent in the isomerization reaction of α,β-unsaturated imide into β,γ-unsaturated imide. The Birch reduction using 2-isopropylbenzimidazole realized a concise and stereoselective synthesis of δ-lactone 14, a sex pheromone of Macrocentrus grandii, while the isomerization reaction using 2-methylbenzimidazole was employed in the highly stereoselective synthesis of the γ-lactone intermediate in the synthesis of depsipeptide antibiotics. These bulky proton sources would be powerful tools to achieve a concise synthesis of natural products.     

Vertically Grown Few-Layer MoS2 Nanosheets on Hierarchical Carbon Nanocages for Pseudocapacitive Lithium Storage with Ultrahigh-Rate Capability and Long-Term Recyclability

Molybdenum disulfide (MoS₂) is an intensively studied anode material for lithium-ion batteries (LIBs) owing to its high theoretical capacity, but it is still confronted by severe challenges of unsatisfactory rate capability and cycle life. Herein, few-layer MoS₂ nanosheets, vertically grown on hierarchical carbon nanocages (hCNC) by a facile hydrothermal method, introduce pseudocapacitive lithium storage owing to the highly exposed MoS₂ basal planes, enhanced conductivity, and facilitated electrolyte access arising from good hybridization with hCNC. Thus, the optimized MoS₂/hCNC exhibits reversible capacities of 1670 mAh g⁻¹ at 0.1 A g⁻¹ after 50 cycles, 621 mAh g⁻¹ at 5.0 A g⁻¹ after 500 cycles, and 196 mAh g⁻¹ at 50 A g⁻¹ after 2500 cycles, which are among the best for MoS₂-based anode materials. The specific power and specific energy, which can reach 16.1 kW and 252.8 Wh after 3000 cycles, respectively, indicate great potential in high-power and long-life LIBs. These findings suggest a promising strategy for exploring advanced anode materials with high reversible capacity, high-rate capability, and long-term recyclability.     

Freestanding Carbon Nanotube Film for Flexible Straplike Lithium/Sulfur Batteries

Flexible lithium/sulfur (Li/S) batteries are promising to meet the emerging power demand for flexible electronic devices. The key challenge for a flexible Li/S battery is to design a cathode with excellent electrochemical performance and mechanical flexibility. In this work, a flexible strap-like Li/S battery based on a S@carbon nanotube/Pt@carbon nanotube hybrid film cathode was designed. It delivers a specific capacity of 1145 mAh g⁻¹ at the first cycle and retains a specific capacity of 822 mAh g⁻¹ after 100 cycles. Moreover, the flexible Li/S battery retains stabile specific capacity and Coulombic efficiency even under severe bending conditions. As a demonstration of practical applications, an LED array is shown stably powered by the flexible Li/S battery under flattened and bent states. We also use the strap-like flexible Li/S battery as a real strap for a watch, which at the same time provides a reliable power supply to the watch.