基于模糊神经元PID算法的注塑机注射速度控制算法研究

基于一款市场较为畅销的注塑机, 设计出一种能精确控制注射速度的模糊神经元PID控制器. 首先, 设计出具有自学能力的神经元PID控制器, 利用模糊算法对其进行优化; 其次, 在原有注射速度线性数学模型的基础上, 构建注塑机注射速度的非线性模型; 最后, 利用MATLAB在所建数学模型的基础上对模糊神经元PID控制器进行仿真实验. 实验结果表明, 所设计控制器具有响应迅速、无超调量、控制精度高、控制稳定等优点.     

Hyperparameter on-line learning of stochastic resonance based threshold networks

Aiming at training the feed-forward threshold neural network consisting of nondifferentiable activation functions, the approach of noise injection forms a stochastic resonance based threshold network that can be optimized by various gradient-based optimizers. The introduction of injected noise extends the noise level into the parameter space of the designed threshold network, but leads to a highly non-convex optimization landscape of the loss function. Thus, the hyperparameter on-line learning procedure with respective to network weights and noise levels becomes of challenge. It is shown that the Adam optimizer, as an adaptive variant of stochastic gradient descent, manifests its superior learning ability in training the stochastic resonance based threshold network effectively. Experimental results demonstrate the significant improvement of performance of the designed threshold network trained by the Adam optimizer for function approximation and image classification.     

Direct visualization of structural defects in 2D semiconductors

Direct visualization of the structural defects in two-dimensional (2D) semiconductors at a large scale plays a significant role in understanding their electrical/optical/magnetic properties, but is challenging. Although traditional atomic resolution imaging techniques, such as transmission electron microscopy and scanning tunneling microscopy, can directly image the structural defects, they provide only local-scale information and require complex setups. Here, we develop a simple, non-invasive wet etching method to directly visualize the structural defects in 2D semiconductors at a large scale, including both point defects and grain boundaries. Utilizing this method, we extract successfully the defects density in several different types of monolayer molybdenum disulfide samples, providing key insights into the device functions. Furthermore, the etching method we developed is anisotropic and tunable, opening up opportunities to obtain exotic edge states on demand.     

An improved evaluation of the neutron background in the PandaX-Ⅱ experiment

In dark matter direct detection experiments,neutron is a serious source of background,which can mimic the dark matter-nucleus scattering signals.In this paper,we present an improved evaluation of the neutron background in the PandaX-II dark matter experiment by a novel approach.Instead of fully relying on the Monte Carlo simulation,the overall neutron background is determined from the neutron-induced high energy signals in the data.In addition,the probability of producing a dark-matter-like background per neutron is evaluated with a complete Monte Carlo generator,where the correlated emission of neutron(s)andγ(s)in the(α,n)reactions and spontaneous fissions is taken into consideration.With this method,the neutron backgrounds in the Run 9(26-ton-day)and Run 10(28-ton-day)data sets of PandaX-II are estimated to be(0.66±0.24)and(0.47±0.25)events,respectively.     

Pharmacokinetic study of tanshinol and ligustrazine in rat plasma after intravenous administration of tanshinol and Danshen Chuanxiongqin Injection

To investigate the effect of ligustrazine on the pharmacokinetic profile of tanshinol after intravenous administration in rats, a sensitive liquid chromatography tandem mass spectrometry method was developed and validated for quantitative determination of tanshinol and ligustrazine in rat plasma. After prepared by protein precipitation, the analytes were separated on a Waters Acquity HSS T3 column (100 × 2.1 mm, 1.8μm) and eluted by 0.1% formic acid in water and acetonitrile at a flow rate of 0.4 ml/min. The precursor–product ion transitions were m/z 197.0 → 135.0 for tanshinol, m/z 417.1 → 255.1 for liquiritin (internal standard) in negative ion mode and m/z 137.1 → 55.0 for ligustrazine in positive ion mode. To avoid the interference of tanshinol metabolite transformation, the stability of analytes in samples collected after administration was assessed. The validated method was successfully applied to a pharmacokinetic study after intravenous administration of single tanshinol and Danshen Chuanxiongqin Injection. After Danshen Chuanxiongqin injection administration, the values of elimination half-time, area under the concentration–time curve and C_o were 0.36 ± 0.13 h, 1.29 ± 0.37 μg/ml h and 10.51 ± 2.58 μg/ml for male rats, respectively. In the single tanshinol group, the corresponding values were 0.56 ± 0.24 h, 1.85 ± 0.44 μg/ml h and 14.11 ± 2.26 μg/ml for male rats—30–40% higher than those for the Danshen Chuanxiongqin Injection group. There was a significant different between male and female rats. This study provided information on the influence of ligustrazine on the pharmacokinetic characteristics of tanshinol after intravenous administration of Danshen Chuanxiongqin Injection in rats, which will be helpful for its clinical application.     

Chemical profiling of bioactive constituents in hop cones and pellets extracts by online comprehensive two‐dimensional liquid chromatography with tandem mass spectrometry and direct infusion Fourier transform ion cyclotron resonance mass spectrometry

Humulus lupulus L. (hop) is highly interesting from a nutraceutical perspective. The hop phytocomplex contains a wide range of bioactive metabolites, and its characterization is challenging. To tackle such a task, for the first time we applied and compared a combined approach consisting of online comprehensive two‐dimensional liquid chromatography with tandem mass spectrometry and direct infusion Fourier transform ion cyclotron mass spectrometry. A reversed phase × reversed phase approach with a shifted gradient in the second dimension ensured selectivity and two‐dimensional space coverage. Hyphenation with an ion trap time‐of‐flight analyzer led to the identification of 83 compounds in 70 min, comprising a novel quercetin derivative and six unknown bitter acids. On the other hand, the direct infusion method was able to identify 40 analytes (except isomers) with high mass accuracy (≤ 0.1 ppm) in less than 1 min analysis time. The developed approach can be used in a complementary way, combining the separation capability and high informative spectra of two‐dimensional liquid chromatography tandem mass spectrometry with the ultra‐high mass accuracy of direct infusion, for potential compound discovery or the accurate profiling of bioactive compounds in different hop cultivars as well as for monitoring processing and storage of hop‐based products.     

基于吸收系数的生脉注射液中聚山梨酯80含量测定新方法

聚山梨酯80又名吐温80，为一种亲水型非离子表面活性剂，是食品、保健品和药品中常用的辅料，作为增溶剂和澄清剂广泛用于中药注射剂。近年来，不良反应的发生使得聚山梨酯80的质量和应用愈加受到重视，有研究认为其加入可能引起注射剂不良反应增加。为避免超量使用，有必要对该辅料的投料加以严格控制。中药注射剂中聚山梨酯80的含量测定是当下研究的热点和难点，可以通过分光光度法、分子排阻-蒸发光散射检测法(SEC-ELSD)、液质联用法(LC-MS)直接测定，也可以水解后法经液相色谱-紫外检测法(HPLC-UV)或气相色谱法(GC)间接测定。但由于聚山梨酯80为聚氧乙烯聚合数目不同的混合物、不同厂家生产的聚山梨酯80化学组分及比例存在较大差异，难以采用统一的转换公式或对照品准确定量。此外，中药注射剂的复杂基质造成的假阳性干扰也对定量提出了挑战。为解决以上问题，以生脉注射液为例，提出基于吸收系数的中药注射剂中聚山梨酯80含量测定新方法。优化检测波长、显色剂种类、液液萃取过程振荡和静置时间，在6个不同品牌仪器上测得聚山梨酯80-硫氰酸钴配合物的吸收系数(E1%_{1 cm})为104.23，相对标准偏差(RSD)为2.08%。生脉注射液稀释10倍后，精密量取供试品溶液1.0 mL，精密加入硫氰酸钴溶液10 mL，二氯甲烷20 mL，涡旋振荡3 min。将混合液移至分液漏斗中，静置30 min，取下层二氯甲烷液，将前1 mL弃去，接收约15 mL，在320 nm处测定吸光度，再根据Lambert-Beer定律，利用获得的吸收系数计算得到聚山梨酯80的含量。方法阴性无干扰，精密度和重复性相对标准偏差均低于3%，平均回收率为98.42%。为进一步验证方法的准确性，分别采用吸收系数法和标准曲线法测定了2个厂家的10批生脉注射液，并与实际投料量比较。配对t检验结果表明，当置信度为95%时，两种方法无显著性差异，吸收系数法测得结果与企业生产中聚山梨酯的实际投料量也无显著性差异。研究采用前人未采用的、灵敏度更高的320 nm为检测波长，显著降低了基质干扰，克服了中药注射剂中聚山梨酯80测定结果与实际投料量难以吻合的问题。吸收系数法无需使用对照品，亦不用制备标准曲线，可为中药注射剂中聚山梨酯80的检查标准提供切实可行的解决方案。所建方法灵敏、准确、快速、简便，为含聚山梨酯80制剂的质量控制提供了关键常数及新的思路。     

The visible and ultraviolet organic light-emitting diodes with germanium dioxide as facile solution-processed anode buffer layer

Germanium dioxide (GeO₂) aqueous solutions are facilely prepared and the corresponding anode buffer layers (ABLs) with solution process are demonstrated. Atomic force microscopy, X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy measurements show that solution-processed GeO₂ behaves superior film morphology and enhanced work function. Using GeO₂ as ABL of organic light-emitting diodes (OLEDs), the visible device with tris(8-hydroxy-quinolinato)aluminium as emitter gives maximum luminous efficiency of 6.5 cd/A and power efficiency of 3.5 lm/W, the ultraviolet device with 3-(4-biphenyl)-4-phenyl-5-tert-butylphenyl-1,2,4-triazole as emitter exhibits short-wavelength emission with peak of 376 nm, full-width at half-maximum of 42 nm, maximum radiance of 3.36 mW/cm² and external quantum efficiency of 1.5%. The performances are almost comparable to the counterparts with poly (3,4-ethylenedioxythiophene):poly (styrenesulfonate) as ABL. The current, impedance, phase and capacitance as a function of voltage characteristics elucidate that the GeO₂ ABL formed from appropriate concentration of GeO₂ aqueous solution favors hole injection enhancement and accordingly promoting device performance.     

Determination of sulfa antibiotic residues in river and particulate matter by field-amplified sample injection-capillary zone electrophoresis

In the present research, field-amplified sample injection–CZE (FASI–CZE) coupled with a diode array detector was established to determine trace level sulfa antibiotic. Sulfathiazole, sulfadiazine, sulfamethazine, sulfadimethoxine, sulfamethoxazole, and sulfisoxazole were selected as analytes for the experiments. The background electrolyte solution consisted of 70.0 mmol/L borax and 60.0 mmol/L boric acid (including 10% methanol, pH 9.1). The plug was 2.5 mmol/L borax, which was injected into the capillary at a pressure of 0.5 psi for 5 s. Then the sample was injected into the capillary at an injection voltage of –10 kV for 20 s. The electrophoretic separation was carried out under a voltage of +19 kV. The capillary temperature was maintained at 20˚C throughout the analysis, and six sulfonamides were completely separated within 35 min. Compared with pressure injection-CZE, the sensitivity of FASI-CZE was increased by 6.25–10.0 times, and the LODs were reduced from 0.2–0.5 to 0.02–0.05 μg/mL. The method was applied to the determination of sulfonamides in river water and particulate matter samples. The recoveries were 78.59–106.59%. The intraday and interday precisions were 2.89–7.35% and 2.77–7.09%, respectively. This provides a simpler and faster method for the analysis of sulfa antibiotic residues in environmental samples.     

Efficient catalytic degradation of single and binary azo dyes by a novel triple nanocomposite of Mn3O4/Ag/SiO2

The strategy of structurally integrating noble metal and metal oxides is expected to offer exceptional opportunities toward emerging functions of all. We report the creation of an efficient hetero-structured nanocatalyst consisting of Mn₃O₄ core, SiO₂ shell impregnated with noble Ag nanoparticles. The triple nanocatalyst Mn₃O₄/Ag/SiO₂ was synthesized by using a facile three-step approach to disperse Ag nanoparticles between the surfaces of functionalized Mn₃O₄ and SiO₂. The physicochemical structural characterization was performed by XRD and FTIR. The surface morphologies were observed by SEM and TEM. The EDX measurements confirmed the composition of the composite. The nanocomposite has been used as a catalyst for the degradation of Direct blue 78 in the presence of sodium borohydride (NaBH₄). It has a drastic catalytic effect as compared to Mn₃O₄/Ag and Mn₃O₄. The rate constant of Direct blue 78 reduction followed the order: Mn₃O₄/Ag/SiO₂ (0.25166 min⁻¹) > Mn₃O₄/Ag (0.07971 min⁻¹) > Mn₃O₄ (0.00947 min⁻¹). The effects of different reaction conditions of the catalytic reaction have been determined. The catalytic activity of the as- synthesized nanocomposite was examined for the binary dyes system by incorporation of an additional dye (Sunset yellow). Its influence on the degradation rate and efficiency of Direct blue 78 was investigated. The nanocatalyst exhibited excellent catalytic activity towards the complete degradation of both the Direct blue 78 and Sunset yellow. The degradation percentage for these dyes reached 99.33 and 94.68%, respectively. The recovery and reusability of the Mn₃O₄/Ag/SiO₂ nanocomposite was studied in the reduction reaction of Direct blue 78. Five consecutive recovery reaction cycles were performed. They revealed high stability and constant efficiency of the catalyst for four cycles.