Superthermostability of nanoscale TIC-reinforced copper alloys manufactured by a two-step ball-milling process

A Cu-TiC alloy, with nanoscale TiC particles highly dispersed in the submicron-grained Cu matrix, was manufactured by a self-developed two-step ball-milling process on Cu, Ti and C powders. The thermostability of the composite was evaluated by high-temperature isothermal annealing treatments, with temperatures ranging from 727 to 1273 K. The semicoherent nanoscale TiC particles with Cu matrix, mainly located along the grain boundaries, were found to exhibit the promising trait of blocking grain boundary migrations, which leads to a super-stabilized microstructures up to approximately the melting point of copper (1223 K). Furthermore, the Cu-TiC alloys after annealing at 1323 K showed a slight decrease in Vickers hardness as well as the duplex microstructure due to selective grain growth, which were discussed in terms of hardness contributions from various mechanisms.     

Doctor-bladed Cu2ZnSnS4 light absorption layer for low-cost solar cell application

The doctor-blade method is investigated for the preparation of Cu2ZnSnS4 films for low-cost solar cell application.Cu2ZnSnS4 precursor powder,the main raw material for the doctor-blade paste,is synthesized by a simple ball-milling process.The doctor-bladed Cu2ZnSnS4 films are annealed in N2 ambient under various conditions and characterized by X-ray diffraction,ultraviolent/vis spectrophotometry,scanning electron microscopy,and current-voltage(J-V) meansurement.Our experimental results indicate that(i) the X-ray diffraction peaks of the Cu2ZnSnS4 precursor powder each show a red shift of about 0.4°;(ii) the high-temperature annealing process can effectively improve the crystallinity of the doctor-bladed Cu 2 ZnSnS 4,whereas an overlong annealing introduces defects;(iii) the band gap value of the doctor-bladed Cu 2 ZnSnS 4 is around 1.41 eV;(iv) the short-circuit current density,the open-circuit voltage,the fill factor,and the efficiency of the best Cu2ZnSnS4 solar cell obtained with the superstrate structure of fluorine-doped tin oxide glass/TiO2/In2S3/Cu2ZnSnS4/Mo are 7.82 mA/cm2,240 mV,0.29,and 0.55%,respectively.     

Microstructural properties and local atomic structures of cobalt oxide nanoparticles synthesised by mechanical ball-milling process

In this study, facile preparation of pure and nano-sized cobalt oxides particles was achieved using low-cost mechanical ball-milling synthesis route. Microstructural and morphological properties of synthesised products were characterised by X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques. XRD results indicated that the fabricated samples composed of cubic pure phase CoO and Co₃O₄ nanocrystalline particles with an average crystallite size of 37.2 and 31.8 nm, respectively. TEM images showed that the resulting samples consisted of agglomerates of particles with average diameter of about 37.6 nm for CoO and 31.9 nm for Co₃O₄. Phase purity of the prepared samples was further investigated due to their promising technological applications. Local atomic structure properties of the prepared nanoparticles were probed using synchrotron radiation-based X-ray absorption spectroscopy (XAS) including X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS). EXAFS data analysis further confirmed the formation of single-phase CoO and Co₃O₄ nanoparticles. In addition, structural properties of cobalt oxide nanoparticles were investigated by performing density functional theory calculations at B3LYP/TZVP level and Born–Oppenheimer molecular dynamics. Theoretical calculations for both prepared samples were found to be consistent with the experimental results derived from EXAFS analysis. Obtained results herein reveals that highly crystalline and pure phase CoO and Co₃O₄ nanoparticles can be synthesised using simple, inexpensive and eco-friendly ball-milling method for renewable energy applications involving fuel cells and water splitting devices.     

Mechanosynthesis of YIG and GdIG: A Structural and Mössbauer Study

We have investigated the mechanosynthesis of gadolinium and yttrium iron garnets by high-energy ball-milling of α-Fe₂O₃ and Gd₂O₃ or α-Fe₂O₃ and Y₂O₃, respectively, followed by short thermal annealings conducted at moderate temperatures. The samples were characterized by X-ray diffraction and Mössbauer spectroscopy, in order to determine the influence of the milling time and annealing conditions on the final products. For as-milled samples of each rare-earth system, the results revealed the formation of perovskite phases, in relative amounts that depend on the milling time. The formation of garnet phases was observed in as-annealed samples treated at 1000°C for 2 h or 1100°C for 3 h, i.e., at very modest annealing requirements when compared with ordinary solid-state-reaction processes performed without previous high-energy milling. Also, the occurrence was verified of a milling time for which the relative amount of garnet phases formed by annealing was maximized. This time depends on the rare-earth composing the garnet phase and on the annealing temperature.     

Substructure of Titanium Dioxide Agglomerates from Dry Ball-milling Experiments

The calciner discharge of TiO₂ white pigments from the sulphate process is ground batchwise in a planetary ball mill, varying the energy of comminution between 0 and 5.1 times the earth's gravitational constant. Particle sizes and specific surfaces of the ground products reveal that the calciner discharge consists of aggregates of 430nm diameter built from 160–210nm TiO₂ crystals. The contact area of a primary particle in an aggregate is about 15% of its surface. The success in comminution of aggregates as a function of grinding energy follows Kick's law. The theory by Rose and Weichert is used to quantify the mechanical strength of the aggregates. Ca. 20% of the aggregates are further agglomerated to granules of ca. 35µm. At all energy levels above a certain threshold, agglomerates break directly into aggregates.     

单斜层状LiMnO2的球磨-离子交换法合成及其电化学性能研究

通过球磨促进固相反应法合成出了具有单斜层状结构的前驱物NaMnO₂，随后通过离子交换得到了单斜层状LiMnO₂。XRD测试结果显示产物为单相。扫描电镜(SEM)和透射电镜(TEM)观测结果显示LiMnO₂的粒子尺寸为300～500 nm，HRTEM分析显示干扰条纹的间距为0.485 nm，基本对应于m-LiMnO₂的(001)晶面间距。红外吸收光谱(IR)和X射线光电子能谱(XPS)被用来测量m-LiMnO₂中Mn-O键的伸缩和弯曲振动吸收和Mn元素的价态。合成的m-LiMnO₂在电化学充放电循环初期表现了较好的电化学性能，但其循环寿命仍需要进一步改善。     

锂离子电池用多孔硅/石墨/碳复合负极材料的研究

在两步高能球磨和酸蚀条件下制得了多孔硅/石墨复合材料，并对其进行碳包覆制成多孔硅/石墨/碳复合材料。通过TEM，SEM等测试手段研究了多孔硅材料的结构。作为锂离子电池负极材料，电化学测试结果表明多孔硅/石墨/碳复合材料相比纳米硅/石墨/碳复合材料有更好的循环稳定性。同时，改变复合体配比、热解碳前驱物、粘结剂种类和用量也会对材料的电化学性能产生较大的影响。其中使用质量分数为10％的LA132粘结剂的电极200次循环以后充电容量保持在649.9 mAh·g^-1，几乎没有衰减。良好的电化学性能主要归因于主活性体-多孔硅颗粒中的纳米孔隙很好地抑制了嵌锂过程中自身的体积膨胀，而且亚微米石墨颗粒和碳的复合也减轻了电极材料的体积效应并改善了其导电性。     

掺Ti球磨NaH/Al复合物的微结构和储氢特性

本文采用机械球磨法制备了(NaH/Al)+x(摩尔分数, %)Ti(x=0, 4, 6, 10)复合物, 研究了不同球磨气氛和Ti催化剂含量对其微结构和储氢性能的影响, 使球磨(NaH/Al)体系储氢的容量达到质量分数为4.01%.     

Making Solid‐Phase Peptide Synthesis Greener: A Review of the Literature

To date, the synthesis of peptides is concurrent with the production of enormous amounts of toxic waste. DMF, CH₂Cl₂, and NMP are three of the most toxic organic solvents used in chemical synthesis and are the most common solvents used for peptide synthesis. Additionally, concerns about the hepatotoxicity caused by exposure to DMF and from the toxic and allergenic nature of additives used in peptide synthesis necessitates the need for a green, environmentally friendly, and safer protocol for peptide synthesis. This review summarizes the current literature on green solid‐phase peptide synthesis successes and challenges encountered. The review concludes with suggestions for future research towards a simple and efficient green peptide synthesis protocol.     

具有18电子结构的Mg2CoH5纳米晶制备及其储氢性能研究

本文研究了Mg2CoH5纳米晶的制备及其储氢性能。在室温和氩气气氛下,以MgH2和纳米Co为原料,采用球磨法制备了Mg2CoH5纳米晶。对所制备Mg2CoH5的组成、结构和形貌进行了表征,并且对Mg2CoH5的储氢性能进行了研究。实验结果表明,通过该种方法制备了纯度较高(产物纯度为79%)的四方结构Mg2CoH5纳米晶,其形貌呈球形且分布较均匀,最频粒径为80 nm。制备的Mg2CoH5纳米晶具有较低的活化能和较好的吸放氢动力学性能,其放氢的脱附焓和脱附熵分别为-115.0 kJ.mol-1H2和-193.6.1 J.mol-1.K-1H2。再氢化时,在543 K时仅7 min内其吸氢量就达到1.5wt%。