微机在有源消声中的应用

本文讨论将微机技术引入单源有源消声器。微机控制其可变参数,使消声系统能对噪声源进行自动跟踪。其参数在一定范围内随着消声情况的变化而变化,始终保持最佳的消声效果。对线状谱噪声可将其剩余噪声控制在本底噪声或比本底噪声稍高一点的范围内(～3dB)。跟踪速度较快,最佳消声状态的稳定性也较好。     

逆p·n·p·矩阵的表征

一个n阶实方阵A,若其各阶主子式皆非正,则称A为p.n.p.矩阵,记作A∈PNP;特别地,若A∈NP且各阶主子式皆负,则称A为p.n.矩阵,记作A∈PN进一步,若n阶实方阵A非奇异,且A^-1∈PNP,则称A为逆p.n.p.矩阵,记作A∈IPNP;特别地,若A^-1∈PN,则称A为逆p.n.矩阵,记作A∈IPN。     

用动态规划方法综合不等距线阵

动态规划方法是综合不等距阵的一个有效方法,但当阵元数比较多时计算量比较大。本文通过对阵元位置进行限制,避免过多的重复计算,使运算量大幅度减少。此外提出了重复迭代方法,可使旁瓣级进一步降低。     

广义Jacobi矩阵的逆特征问题

本文主要讨论广义Jacobi阵及多个特征对的广义Jacobi阵逆特征问题.通过相似变换将广义Jacobi阵变换为三对角对称矩阵,其特征不变、特征向量只作线性变换,再应用前人理论求得广义Jacobi阵元素ai,|bi|,|ci|有唯一解的充要条件及其具体表达式.     

奇异协方差阵下有效前沿及有效组合的解析解

利用广义逆矩阵研究了协方差阵奇异时的投资组合问题,突破了传统方法中要求协方差阵可逆的限制,得到了证券市场存在有效组合的充要条件,并给出了有效前沿和有效组合的解析解,成功地推广了经典Markowitz模型,同时还将有助于证券组合有效子集的深入研究.     

基于FPGA的超高速线阵CCD信号采集系统的设计与实现

线阵CCD已广泛应用于在线检测、图像识别等系统,目前高帧率采集系统多在200~500Hz之间。高速线阵CCD采集系统,如1K甚至10KHz以上的采集要求,设计难度大,电路实现复杂,需要专用处理器,产品成本高,提出了一种采用并行高速FPGA驱动线阵CCD,通过常规分立元件完成模拟信号处理,实现数字信号实时传输的方案。该方案不仅简化了硬件设计上的难度,在同等性能情况下,可实现每秒万帧的高速采样,大幅度降低了成本。方案选用Altera FPGA作为控制核心,实现高速信号采集的同时,在片上实现一定的图像算法,不仅加速了图像处理速度,同时降低了计算机的处理压力。最后,本电路通过USB2.0接口,完成数据的实时传输。设计具有高帧率、高灵敏度、性能稳定,便携使用等特点,同时还有一定的通用性,已应用于一些光学系统中。     

Spectral analysis of the UFBG-based acousto optical modulator in V–I transmission matrix formalism

In this study, the V-I transmission matrix formalism （V-I method） is proposed to analyze the spectrum characteristics of the uniform fiber Bragg grating （FBG）-based acousto--opfic modulators （UFBG-AOM）. The simulation results demon- strate that both the amplitude of the acoustically induced strain and the frequency of the acoustic wave （AW） have an effect on the spectrum. Additionally, the wavelength spacing between the primary reflectivity peak and the secondary reflectivity peak is proportional to the acoustic frequency with the ratio 0.1425 nm/MHz. Meanwhile, we compare the amount of calculation. For the FBG whose period is M, the calculation of the V-I method is 4 × （2M-l） in addition/subtraction, 8 × （2M - 1） in multiply/division and 2M in exponent arithmetic, which is almost a quarter of the multi-film method and transfer matrix （TM） method. The detailed analysis indicates that, compared with the conventional multi-film method and transfer matrix （TM） method, the V-I method is faster and less complex.     

Influence of roughness on the detection of mechanical characteristics of low-k film by the surface acoustic waves

The surface acoustic wave （SAW） technique is a precise and nondestructive method to detect the mechanical charac- teristics of the thin low dielectric constant （low-k） film by matching the theoretical dispersion curve with the experimental dispersion curve. In this paper, the influence of sample roughness on the precision of SAW mechanical detection is inves- tigated in detail. Random roughness values at the surface of low-k film and at the interface between this low-k film and the substrate are obtained by the Monte Carlo method. The dispersive characteristic of SAW on the layered structure with rough surface and rough interface is modeled by numerical simulation of finite element method. The Young＇s moduli of the Black DiamondTM samples with different roughness values are determined by SAWs in the experiment. The results show that the influence of sample roughness is very small when the root-mean-square （RMS） of roughness is smaller than 50 nm and correlation length is smaller than 20 μm. This study indicates that the SAW technique is reliable and precise in the nondestructive mechanical detection for low-k films.     

A Multiple Resonant Mode Film Bulk Acoustic Resonator Based on Silicon-on-Insulator Structures

With the rapid development of wireless technol- ogy, the demand for integrating multi-band devices has spurred substantial research interest. Research on CMOS compatible radio-frequency （rf） devices has also attracted significant attention. The resonant frequency of film bulk acoustic resonators （FBARs） is mainly determined by the thickness of the piezo- electric film, complicating the integration of differ- ent frequencies on a single chip. One report real- ized multiple resonant frequencies around 2.0 GHz by changing the quality of the electrode. Another re- port obtained the 2.5 GHz main frequency response with a quality factor （Q） of 101.8 and some spuri- ous resonances, while these spurious resonances were irregular.     

具有变视场性能的中红外光谱系统设计与研究

为了用同一设备对目标在中红外光谱段同时实现跟踪和捕获,针对像元尺寸为15μm×15μm的新型大面阵640×512红外探测器,设计了一套大面阵中红外光谱变视场探测成像系统,系统光谱范围为3.7~4.8μm,F数为4.0,窄视场为0.45°,宽视场为0.90°,通过利用机械机构在窄视场结构中切入两片透镜实现宽视场结构,应用二次成像技术不仅有效减小了前固定组透镜口径,而且实现了100%冷光阑匹配,减小了进入红外探测器的杂光。该系统仅采用了锗和硅两种常用的红外材料,为了有效校正系统的轴外像差和高级像差,并保证变视场系统两种结构的齐焦性,系统应用了非球面技术。设计结果表明,奈奎斯特频率33lp·mm-1处,系统的窄视场和宽视场的传递函数值均优于0.2,所有视场畸变均小于0.5%,具有优良的成像性能。在极端温度-35~55℃范围时,该大面阵中红外光谱变视场探测成像系统窄视场结构和宽视场结构的成像质量变化不大,满足使用要求。