腔镜形变对圆筒组合型CO_2激光器模式的影响

针对具有锁相结构的圆筒组合型CO2激光器,分析了其注入锁定的原理,利用等价条形腔理论,建立了分析其输出基模的数学模型。利用该模型,研究了不同形变量对圆筒形腔输出基模的影响。结果表明,为了获得与注入光束模式类似的光场分布,复曲面镜与圆筒形谐振腔中平面镜镜面中心的形变量应控制在0.07倍波长以内。同时,分析在不同腔镜参数情况下腔镜形变对输出模式造成的影响,其结果有利于进一步优化谐振腔的参数设计。     

基于ADS的射频前端预选器的设计与仿真

预选器作为射频接收前端的主要组成部分,对整个射频信号的接收有着重要的作用。针对实际无线通信环境下的应用,使用ADS软件设计了一种20MHz~3.6GHz的射频前端预选器。在该设计中采用了亚倍频程滤波器组进行分段滤波和抑制镜像信号,并利用低噪声放大器（LNA）对信号进行放大并减小噪声,并对设计的预选器关键部分的插入损耗、增益、噪声系数等指标进行了仿真。仿真结果显示,所设计的预选器各项性能指标均已达到了预期的要求,对接收机前端系统的研究和完善具有重要的参考价值。     

KDP晶体相位匹配角理论预测模型及其验证分析

在高功率固体激光器的终端光学组件内, 大口径薄型KDP (KH₂PO₄)晶体的精密装配和校准是实现惯性约束核聚变的关键技术之一. 为了达到晶体在线安装高效高精度的要求, 需要测量高功率激光三次谐波转换效率达到最高时的晶体相位匹配角分布. 本文针对Ⅰ/Ⅱ类大口径薄型KDP晶体三次谐波转换的方式, 根据晶体的非线性光学属性获得了晶体不同位置相位匹配角之间的关系; 根据激光束在晶体内的传输路径分析得到了晶体面形、相位匹配角与激光三次谐波转换效率达到最高时 晶体最佳偏转角之间的相互关系. 在此基础上, 建立了Ⅰ/Ⅱ类KDP晶体相位匹配角的理论预测模型, 并利用实验进行了验证和分析. 实验结果表明, 晶体相位匹配角的预测值与实验值之差在10.0 μrad以内, 验证了Ⅰ/Ⅱ类KDP晶体相位匹配角理论预测模型的正确性, 为获得晶体全口径相位匹配角分布提供了简单、高效的预测方法.     

掺钆液闪中子探测器的研制

中子在探测器中能产生与暗物质粒子(WIMPs)类似的核反冲信号,对于低背景的暗物质直接探测实验,精确测量和排除中子的干扰尤其重要。为测量中国锦屏地下实验室(CJPL)中子本底的通量,研制了高效的、具有很强"中子-伽马"分辨的掺钆液闪快中子探测器。介绍了掺钆液闪中子探测器的研制和性能,包括探测器形状和尺寸的设计,液体闪烁体类型、光电倍增管型号以及液闪容器材料的选择,探测器的伽马能量刻度以及中子与伽马信号的甄别。用Am-Be中子源对探测器进行探测效率刻度,得到阈值为0.2 MeV等效电子能量的中子探测效率为(6.30±0.30)%,满足中国锦屏地下实验室对中子通量测量的要求。     

MNZ超材料的电磁特性

主要围绕磁导率接近0的MNZ超材料,通过理论分析和数值模拟方法对MNZ材料的电磁特性进行了研究。针对线源置于二维MNZ材料内部的情况,通过理论详细分析了在MNZ材料和空气交界处的阻抗匹配特性和传播常数的连续性,基于有限元数值方法模拟验证了电磁场在MNZ材料边界处的等幅同相特性,从而实现了均匀平面波的传播特性。同时,考虑到将线源置于空气中有助于辐射出电磁能量,通过数值模拟分析了电磁波由空气入射到MNZ材料的电磁特性,发现在特定极化条件下,只能当电磁波波前与MNZ材料边界平行时,才能较好地实现阻抗匹配,从而基于MNZ材料实现新颖的辐射特性。     

Modal analysis of measurements from a large-scale VIV model test of a riser in linearly sheared flow

Large-scale model testing of a tensioned steel riser in well-defined sheared current was performed at Hanøytangen outside Bergen, Norway in 1997. The length of the model was 90 m and the diameter was 3 cm. The aim of the present work is to look into this information and try to improve the understanding of vortex-induced vibrations (VIV) for cases with very high order of responding modes, and in particular to study if and under which circumstances the riser motions would be single-mode or multi-mode. The measurement system consisted of 29 biaxial gauges for bending moment. The signals are processed to yield curvature and displacement and further to identify modes of vibration. A modal approach is used successfully employing a combination of signal filtering and least-squares fitting of precalculated mode-shapes. As a part of the modal analysis, it is demonstrated that the equally spaced instrumentation limited the maximum mode number to be extracted to be equal to the number of instrumentation locations. This imposed a constraint on the analysis of in-line (IL) vibration, which occurs at higher frequencies and involves higher modes than cross-flow (CF). The analysis has shown that in general the riser response was irregular (i.e. broad-banded) and that the degree of irregularity increases with the flow speed. In some tests distinct spectral peaks could be seen, corresponding to a dominating mode. No occurrences of single-mode (lock-in) were seen. The IL response is more broad-banded than the CF response and contains higher frequencies. The average value of the displacement r.m.s over the length of the riser is computed to indicate the magnitude of VIV motion during one test. In the CF direction the average displacement is typically 1/4 of the diameter, almost independent of the flow speed. For the IL direction the values are in the range 0.05–0.08 of the diameter. The peak frequency taken from the spectra of the CF displacement at riser midpoint show approximately to be equal to the Strouhal frequency. The peak frequency in IL direction was typically twice the Strouhal frequency.     

NUMERICAL SIMULATION OF COMPLICATED PIPE FLOW WITH k-εMODEL

In this paper, turbulence in a complicated pipe is simulated by using the k-ε model. The ladder-like mesh approximation is used to solve the problem of complicated boundary with the result of numerical simulation favorable. Two computational examples are given to validate the strong adaptability and stability of k-ε model.     

填料特性对聚乙烯基复合材料性能的影响

在高密度聚乙烯中分别添加粒状，纤维状和层状填料，制备了结构和性能不同的几种聚乙烯基复合材料。利用Ｃｅａｓｔ仪器化冲击试验机，Ｉｎｓｔｏｒｏｎ４３０２万能材料试验机，ＳＲＶ摩擦磨损试验机，ＭＨＫ－５００型环－块磨损试验机等，研究了填料的形态、性质对聚乙烯基复合材料之机械性能和摩擦磨损性能的影响。