n型主动拉曼增益原子介质中的光学双稳态

研究了主动拉曼增益原子介质在单向环形腔中的光学双稳态．该系统是一个相干共振的n型四能级原子系统,可在室温下实现,有能级失谐量、原子数密度、抽运场、控制场等较多的可调参数,且有无增益的透明窗口．完全通过解析方法定量给出实现光学双稳态的条件,以及可调参数的取值范围,并进一步给出实现光学多稳态的条件,为实验上实现光学双稳态与多稳态提供了理论依据．     

N-取代邻苯二甲酰亚胺类衍生物的设计、合成及活性评价

结合中药脱皮马勃中分离得到的3,5-二羟基邻苯二甲酰亚胺和邻苯二甲酰亚胺类化合物的结构设计合成了一系列N-取代-3,5-二甲氧基邻苯二甲酰亚胺及N-取代-3,5-二羟基邻苯二甲酰亚胺类衍生物,其结构经¹H NMR,¹³C NMR和MS分析确证. 选取人肺腺癌细胞A549及人脐静脉血管内皮细胞HUEVC为测试细胞株,评价了所合成化合物的体外抗肿瘤及抗血管生成活性,结果表明,部分化合物表现出一定的活性.     

旋转浓缩对灰葡萄孢代谢产物中除草活性物质的影响

用旋转浓缩法浓缩灰葡萄孢代谢产物的培养滤液,以试样对反枝苋种子发芽的校正抑制率为活性指标测定蒸出液和浓缩液的除草活性,同时测定蒸出液的紫外吸收曲线;结果发现,浓缩至原体积一半时的蒸出液和浓缩至干后的蒸出液均表现出生物活性,对反枝苋种子发芽的抑制率分别为90．4％和84．6％,两种蒸出液的紫外吸收曲线相似,均在232nm处有最大吸收;表明浓缩过程中除了溶剂水被蒸出外,至少还有1种活性物质被蒸出或损失,其在232nm有最大吸收;浓缩至1／2体积的蒸出液在232nm的吸光值(0．893)比浓缩至干的蒸出液在该处的吸光值(0．697)大,表明浓缩前期该活性物质的损失量更高。     

边界条件都含有特征参数的四阶微分算子特征值的依赖性

本文考虑了区间[a,b]两端四个边界条件都含有特征函数的四阶微分算子特征值的依赖性问题,证明了特征值不仅连续依赖而且可微依赖于问题的各个参数(系数函数,权函数,区间端点,边界条件系数矩阵),并且给出了相应的微分表达式.特别地,给出特征值关于特征参数依赖的边界条件系数矩阵的Frechet导数.     

稀薄气体动力学矩方法研究综述

临近空间位于航天器入轨与返回的必经区域, 也是临近空间高超声速飞行器长航时飞行空域, 空间环境的特殊性决定了飞行器在穿越时必须考虑稀薄大气环境对飞行器气动力防隔热通讯及控制的影响.Boltzmann方程作为描述气体分子速度分布函数演化规律的微分-积分形式, 在一定条件下能够描述从自由分子流到连续流全流域流动现象.作为Boltzmann方程的宏观表达形式, 矩方程这一经典流体力学方程形式涵盖了Euler方程N-S方程Burnett方程super-Burnett方程及近年来发展的广义流体力学方程——非线性本构关系模型等.由于成熟的CFD数值计算理论及有限矩方程较高的计算效率, 滑移过渡流矩方法相比粒子仿真与Boltzmann模型方程方法具有十分显著的优势和巨大的工程应用潜力.因此, 对近年来传统及新型矩方法研究所取得的进展进行归纳总结, 并针对关键科学问题开展理论与数值计算方法研究, 具有十分重要的理论与工程应用价值.      

BCS-BEC渡越过程中超流费米气体Efimovian膨胀的研究

基于耦合流体力学方程组,分别研究了各向同性和各向异性轴对称势阱下Bardeen-CooperSchrieffer–Bose-Einstein condensate(BCS-BEC)渡越过程中超流费米气体的Efimovian膨胀.当费米气体处于幺正极限,体系标度不变,气体膨胀尺寸展现出一系列平台结构,气体的演化由对数周期函数描述;当费米气体处于非幺正极限超流区域,体系标度不变性破缺,气体的演化偏离对数周期变化;另外我们还发现对于各向异性的费米气体,即使处于幺正极限,谐振子势的各向异性也会导致体系标度不变性破缺.     

HIAF-SRing的等时性模式光学设计

高精度环形谱仪SRing作为HIAF装置的核心之一,是获取高品质放射性次级束,并将束流用于加速器技术研究、原子物理及核物理实验的关键设备。SRing有三种运行模式:等时性模式、正常模式与内靶模式。等时性模式下,SRing运行在特殊线性光学设置下,可以精确测量寿命低至几十微秒的原子核的质量。介绍SRing等时性模式的线性光学及高阶项校正的设计方案。在使用程序GICOSY进行等时性高阶项校正数值计算后,将得到的光学传输矩阵输入到程序MOCADI进行粒子跟踪模拟。以γ_t=1.43的等时性模式为例,SRing的动量接收度为±0.20%,粒子跟踪结果显示,在仅满足一阶等时性条件时SRing的质量分辨能力R=1.6×104。在保证动量接收度不变的前提下,考虑了等时性高阶项校正后SRing的质量分辨能力提高到R=1.2×106,达到设计要求。The Spectrometer Ring, as the most important experiment terminal of the High Intensity heavy-ion Accelerator Facility (HIAF) project, is a key device to obtain high-quality radioactive ion beams (RIBs) for atomic physics, nuclear physics experiments and accelerator technology researches. Three operation modes including the isochronous mode, the normal mode and the internal target mode, have been designed for the SRing. In the isochronous mode, the SRing operates under a special ion optics and could be used for precision mass measurement of short-lived nuclei with half-life shorter than several tens of microseconds. This study aims to design the ion optics for the isochronous mode and improve the mass resolving power of the SRing with higher-order ion-optical correction scheme for isochronism while preserve a large momentum acceptance of SRing. The ion optics and the higher-order correction for the isochronous mode are calculated with the code MAD-X and GICOSY respectively. Three ion optics with γ_t=1.43, 1.67, 1.83 settings have been calculated. The code MCOADI which utilizes the matrixes generated by the code GICOSY is used for particles tracking to verify the correction results. For the ion-optical setting of γ_t=1.43 with a momentum acceptance of ±0.20%, the mass resolving power of the SRing could be improved from R=1.6×104 to R=1.2×106, after isochronous higher-order corrections.     

CSR-LINAC IH-RFQ的高频电磁设计

中国科学院近代物理研究所在CSR-LINAC项目中设计了一台108.48 MHz的IH型RFQ直线加速器。该RFQ可以将质荷比为3~7的离子从4 keV/u加速到300 keV/u。在完成束流动力学设计的基础上,主要针对RFQ腔体的高频电磁设计展开了研究,同时利用了电磁场仿真和束流动力学模拟来研究腔体的四极场不平整度和二极场及其动力学影响。未经调谐的情况下,腔体的谐振频率为108.15 MHz,腔体空载品质因子Q₀为5 910,腔体功耗为123 kW。通过在支撑板两端增加底切的设计,将腔体的四极场不平整度由-21%~ 12%优化至±2.5%,满足了束流动力学要求。腔体的二极场为-3%~ -2.2%,使得束流在垂直方向小幅振荡,RFQ的垂直方向接受度减小5%。为了保证功率馈入时反射较小,将耦合器设置在临界耦合状态,耦合面积为940 mm2。为了补偿腔体的频率偏差和漂移,设计了调谐量分别为707和132 kHz的固定调谐器和可动调谐器。The 108.48 MHz IH type RFQ for CSR-LINAC project is under design at Institute of Modern Physics, Chinese Academy of Sciences. This RFQ can accelerate heavy ions with mass to charge ratio of 3~7 from 4 keV/u to 300 keV/u. According to the beam dynamics requirement, the RF structure design has been finished. The quadrupole field unflatness and dipole field of the cavity were studied by electromagnetic simulation and beam dynamics simulation. The frequency of the cavity without tuning is 108.15 MHz, the Q₀ of the cavity is 5910, and the RF power loss is 123 kW. The quadrupole field unflatness of ±2.5%,which was -21%~12% before optimizing, is achieved to meet dynamics requirement through the undercuts in cavity supporters. The dipole field of -3%~ -2.2% causes the oscillation of the beam center and acceptance reduction of 5%. The power coupler must be in critical coupling state with the coupling area of 940 mm2 for minimum reflection coefficient. The tuners, consist of coarse and fine tuners with frequency shift of 707 and 132 kHz respectively, is used for tuning of frequency deviation of the cavity.     

HIAF-BRing的双向涂抹注入模拟

BRing是HIAF工程的主加速器,其设计流强为每个脉冲内的粒子数1×1011个（238U34+）,为了达到此设计流强,注入增益应达到88倍以上。BRing采用了双向涂抹注入方案,其满足BRing的注入增益要求,同时具有注入时间短和累计束分布较均匀而减小了空间电荷效应的特点。双向涂抹注入方案利用水平和垂直两组凸轨磁铁以及倾斜的静电偏转板,在水平相空间和垂直相空间内同时进行涂抹。为了检验双向涂抹注入方案能否达到BRing的设计要求,利用ORBIT程序对双向涂抹注入过程进行了模拟,模拟结果显示,在单次双向涂抹注入113圈的情况下,注入效率为97.7%,注入增益达到110.3倍,满足了BRing流强要求。累积束的分布相对均匀,空间电荷效应引起的工作点漂移约为-0.02,粒子因共振损失风险很小。针对注入束流偏角、切割板角度、工作点偏差和Bump延时等不同注入参数进行了误差分析,结果显示BRing的双向涂抹注入效率对注入参数偏差的容忍度较高。BRing is the main accelerator of High Intensity heavy Ion Accelerator Facility(HIAF) and its design current is 1×1011 particles per pulse (238U34+). To accumulate beams up to the design current, the injection gain has to reach 88. Two planes painting injection scheme is proposed for BRing. This scheme uses a tilted electrostatic septum and 8 bump magnets to paint beams into horizontal and vertical phase space simultaneously. It can inject enough beams into the ring in a short time and paint beams uniformly. The injection process is simulated using ORBIT code and 113 turns is injected into BRing with an injection efficiency of 97.7% which meets the requirement for beam current of BRing. The accumulated beams are distributed uniformly in transverse and hence have a little tune shift of -0.02 which reduces the risk of beam loss due to the resonance. Errors of injection parameters are analysed and the result shows two planes painting injection scheme has a high tolerance for errors of injection parameters.     

十二醇聚氧乙烯醚的表面性能及在水悬浮剂中的应用

探讨了十二醇聚氧乙烯醚(AEO)的EO链长对其临界胶束浓度(cmc)、表面张力(γcmc)、胶束生成自由能(ΔGm)、分子面积(Acmc)和亲水亲油平衡(HLB)值等表面性能的影响;同时研究了不同EO链长的AEO对质量分数25%代森锰锌水悬浮剂(SC)的流变性能[黏度、储能模量(G’)、流动点时的应变(γflow)、触变性]和物理贮存性能(热贮前悬浮率、热贮后悬浮率和倾倒性)的影响.结果发现,AEO的cmc,γcmc,ΔGm,Acmc和HLB值随着EO链长的增加而增大;AEO能够明显改善代森锰锌SC的黏度,以AEO-9所制备的SC黏度最小,且AEO的EO链长越长,所对应的SC结构恢复越慢,恢复慢的样品其倾倒残留率过高;G’和γflow能反映SC内部结构变化,可作为评价农药SC物理稳定性流变学指标.