非富勒烯受体DA'D型稠环单元的结构修饰及电池性能研究

近年来,设计和合成高性能非富勒烯受体(NFAs)材料已经成为太阳能电池研究领域的前沿课题。基于DA'D型稠环结构的NFAs由于具有吸光系数高、能级和带隙可调、结构易于修饰、分子可高效合成、光电学性能优异等优点而受到了越来越广泛的关注。在短短7年的时间里,能量转换效率(PCE)从3%~4%提高到18%。2019年初邹应萍等报道了一个优秀的受体分子Y6,与PM6共混制备单结电池,获得了15.7%的能量转换效率。Y6类受体材料的中心给电子单元为DA'D型稠环结构,缺电子单元(A')通过氮原子与两个给电子单元(D)并联形成稠环结构,这有助于降低前线分子轨道能级并增强吸收,同时与氮相连的两个烷基链和位于噻吩并噻吩β位的两个侧链则有助于提高溶解度及调节结晶性。自Y6问世以来,人们对分子的结构剪裁进行了深入的研究,并报道了数十种新的结构。在这些新的受体中,DA'D部分的结构裁剪对提高器件效率和太阳能电池的性能起着至关重要的作用。本文对A'、D单元和侧链结构修饰的研究进展进行了综述。通过选择几组受体,对最近报道的分子进行分类,并将它们的光学、电化学、电学和光电性质与精确的结构修饰相关联,从而对结构-性能关系进行全面概述。     

脱硫石膏制备硫酸钙晶须结晶动力学研究

结晶动力学能够揭示结晶过程本质,通过测定溶液中Ca2浓度来确定硫酸钙晶须的转化率,从而确定硫酸钙晶须结晶动力学参数,得到转化率与时间的关系式:X=1/｛1+e6^[-10.01977t(0.0956-c)+1.1188]｝,(0≤t≤6.0).研究了影响硫酸钙晶须结晶动力学的影响因素降温速率和陈化时间,利用SEM对制备的硫酸钙晶须进行表征.结果表明:自然冷却条件下,陈化时间6h,制备出的硫酸钙晶须结晶发育完整,晶须平均长径比达到150,平均直径为2.1 μm.     

LaNi0.5Co0.5O3催化剂对甲烷二氧化碳干重整反应在CO2渗透膜反应器中的影响

制备了混合导体膜反应器,通过电化学方法捕获CO2,并将其用于甲烷二氧化碳干重整反应中.采用XRD, SEM,TPR等技术系统研究了LaNi0.5Co0.5O3催化剂在膜反应器中对甲烷二氧化碳干重整反应的影响.结果表明:LaNi0.5Co0.5O3催化剂在甲烷干重整反应中能原位析出纳米金属Ni和Co,对反应起到了较好的催化作用,同时抑制了积碳.催化剂还具有良好的氧化还原性能,可以循环利用.     

季铵盐改性蒙脱石的制备与表征

采用十六烷基三甲基氯化铵(CTAC)对钠基蒙脱石(MMT)进行季铵化改性,制备有机蒙脱石(CMMT),对改性后的蒙脱石进行X射线衍射(XRD)、电位分析法(PA)、红外光谱(FT-IR)和热分析(TGA)等分析表征,并用改性后的蒙脱石吸附五氟尿嘧啶(5-FU)后测定并比较其载药量.结果表明,改性剂已成功插入到蒙脱石的层间;相比于钠基蒙脱石,有机蒙脱石的层间距和热稳定性均有所增大;当制备季铵盐有机改性蒙脱石时,反应温度为80℃,且CTAC的用量是MMT的2.5倍阳离子交换容量时,形成的有机蒙脱石的阳离子化程度和对5-FU的载药量最高.此外,考察并比较了有机蒙脱石和钠基蒙脱石的体外细胞毒性,结果显示有机蒙脱石具有更好的生物相容性和更低的细胞毒性.     

基于NiCo2O4纳米片电极的非对称混合电容器

The looming global energy crisis and ever-increasing energy demands have catalyzed the development of renewable energy storage systems. In this regard, supercapacitors (SCs) have attracted widespread attention because of their advantageous attributes such as high power density, excellent cycle stability, and environmental friendliness. However, SCs exhibit low energy density and it is important to optimize electrode materials to improve the overall performance of these devices. Among the various electrode materials available, spinel nickel cobaltate (NiCo₂O₄) is particularly interesting because of its excellent theoretical capacitance. Based on the understanding that the performances of the electrode materials strongly depend on their morphologies and structures, in this study, we successfully synthesized NiCo₂O₄ nanosheets on Ni foam via a simple hydrothermal route followed by calcination. The structures and morphologies of the as-synthesized products were characterized by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller (BET) surface area analysis, and the results showed that they were uniformly distributed on the Ni foam support. The surface chemical states of the elements in the samples were identified by X-ray photoelectron spectroscopy. The as-synthesized NiCo₂O₄ products were then tested as cathode materials for supercapacitors in a traditional three-electrode system. The electrochemical performances of the NiCo₂O₄ electrode materials were studied and the area capacitance was found to be 1.26 C·cm^-2 at a current density of 1 mA·cm^-2. Furthermore, outstanding cycling stability with 97.6% retention of the initial discharge capacitance after 10000 cycles and excellent rate performance (67.5% capacitance retention with the current density from 1 to 14 mA·cm^-2) were achieved. It was found that the Ni foam supporting the NiCo₂O₄ nanosheets increased the conductivity of the electrode materials. However, it is worth noting that the contribution of nickel foam to the areal capacitance of the electrode materials was almost zero during the charge and discharge processes. To further investigate the practical application of the as-synthesized NiCo₂O₄ nanosheets-based electrode, a device was assembled with the as-prepared samples as the positive electrode and active carbon (AC) as the negative electrode. The assembled supercapacitor showed energy densities of 0.14 and 0.09 Wh·cm^-3 at 1.56 and 4.5 W·cm^-3, respectively. Furthermore, it was able to maintain 95% of its initial specific capacitance after 10000 cycles. The excellent electrochemical performance of the NiCo₂O₄ nanosheets could be ascribed to their unique spatial structure composed of interconnected ultrathin nanosheets, which facilitated electron transportation and ion penetration, suggesting their potential applications as electrode materials for high performance supercapacitors. The present synthetic route can be extended to other ternary transition metal oxides/sulfides for future energy storage devices and systems.     

水热法制备Nd3+-介孔TiO2/GO复合材料及光催化性能研究

采用水热法首先制备稀土Nd3+掺杂介孔TiO2,进而复合氧化石墨烯(GO)合成了系列Nd3+-介孔TiO2/GO复合材料.通过X射线衍射(XRD)、透射电镜(TEM)、孔结构分析(BJH与BET)、X射线光电子能谱(XPS)和紫外-可见漫反射(UV-vis)等测试手段对样品的微观结构、形貌、样品表面各元素价态及谱学性质进行表征,并以甲基橙模拟污染物测试其光催化性能.结果表明,所制样品均为锐钛矿结构TiO2,晶粒尺寸在3~4 nm之间;从UV-vis测试结果分析可知,与Nd3+-介孔TiO2和TiO2/GO相比,稀土Nd3+和GO的协同效应更能有效减小TiO2半导体禁带宽度,从而增加其对可见光的吸收.此外,不同光照射下光催化降解甲基橙的实验表明,所制备样品均有较强的紫外及可见光光催化性能,其中系列Nd3+-介孔TiO2/GO复合体系可见光光催化性能更为显著.     

美国静力学教材分析

为对美国静力学教材有较为全面的理解,以便于在教学和教材建设中参考借鉴,本文研究这些教材的历史发展与现状。概述美国静力学教材的起源与演变。选择有代表性的7本仍在使用的教材,考察这些教材的主要内容及其教学处理,分析这些教材的教学理念和特点。     

卟啉基非金属纳米片用于可见光光催化制氢

本文基于密度泛函理论预测了一种用于可见光范围光催化制氢的新型二维非金属纳米材料，该材料可以由HTAP分子脱氢聚合得到，具有良好的结构稳定性，且带隙为2.12 eV，可以实现可见光区域的光捕获. 材料的带边能级位置恰好包裹水的氧化还原电位，有利于实现全光解水. 电子的迁移率略高于空穴的迁移率，有利于光生载流子的分离. 光生电子可以提供足够的驱动力使得析氢反应自发进行.