Comparison of the thermal behavior of three cellulose fibers mercerized or submitted to solar degradation

Comparison of Lyocell, modal and viscose fibers was performed by means of differential scanning calorimetry, thermogravimetry and scanning electron microscopy. Thermal analysis was performed in air atmosphere. Samples were mercerized (21.3 g 100 mL-1) or submitted to solar radiation (seven months). Solar degraded samples presents a higher thermal stability and are initially less degraded. Furthermore, Lyocell fiber is the most stable under thermal degradation conditions. Heating produces a reduction of the fiber diameter (about 50%). This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermal degradation behaviors of some branched and linear polysiloxanes

The thermal degradation behaviors of some branched and linear polysiloxanes were studied by thermogravimetric (TG) analysis and infrared (IR) spectroscopy, and the effect of phenyl content on the thermal stability of the tested branched polysiloxanes was investigated. The branched polysiloxanes with phenyl obtain higher thermal stability at lower temperature. The degradation residues of the examined branched polysiloxanes at 800 °C are rather high, 65.1-77.6% in N₂ and 40.5-66.5% in air, respectively. However, the amount of solid residue increases with decrease in phenyl content in both N₂ and air atmospheres. It was found that the thermal stability of the branched polysiloxanes is higher than that of the linear one, which indicated that the branched structure benefits the formation of a crosslink in the solid residue.     

载体对负载型TiO2催化剂光催化性能的影响

 以活性碳（AC）和镁铝尖晶石（MA）为载体，采用真空吸附水解法制备了负载型光催化剂TiO2／AC和TiO2／MA，并采用TiO2溶胶负载法制备了活性碳负载催化剂TiO2（C）／AC．以氯仿为探针分子研究了其在催化剂上的吸附及光催化降解反应性能．结果表明，催化剂的制备方法、TiO2负载量与载体的吸附性能对光催化活性有明显的影响．通过优化制备条件，TiO2／AC催化剂的催化活性可提高到纳米TiO2的2．5倍．氯仿在AC上的饱和吸附量较高，但吸附强度较弱；在纳米TiO2上的吸附情况则正好相反．氯仿在AC和TiO2上吸附性质的差异有利于吸附在TiO2／AC上的氯仿分子从活性碳载体向TiO2光催化活性中心迁移．镁铝尖晶石载体对光催化反应没有明显的促进作用，与其基本上不吸附氯仿分子有关．与TiO2胶体负载法相比，真空吸附水解法是一种较好的负载型TiO2光催化剂制备方法．     

Role of montmorillonite in flame retardancy of ethylene-vinyl acetate copolymer

The effects of non-treated (MMT), organophilic (OMM), and olefin/silicone polymer intercalated (IMM) montmorillonites on the thermal stability of ethylene-vinyl acetate copolymer (EVA) and on the flammability of magnesium hydroxide filled EVA were studied. The influence of various treatments on the delamination of montmorillonites in EVA was detected by rheological measurements and by Raman microscopy. The latter was a unique method for rapid detection of the dispersion also in highly filled EVA. Enhancement of thermo-oxidative stability of EVA and flame-retarded EVA could be observed by thermal analysis in the presence of variously treated montmorillonites. The flame-retardant efficiency of magnesium hydroxide was improved by simultaneous application of MMT and IMM. The increased performance of magnesium hydroxide was explained by the rheological effect of the IMM, catalytic effect of MMT and chemical interactions of montmorillonites with the metal hydroxide.     

Identification of a chemical indicator of the rupture of 1,4-β-glycosidic bonds of cellulose in an oil-impregnated insulating paper system

In this study, headspace gas chromatography/mass spectrometry has been used to assess the volatile by-products generated by the ageing of oil-impregnated paper insulation of power transformers. Sealed-glass ampoules were used to age under oxidative conditions 0.5-g specimens of insulating paper in 9 mL of inhibited mineral oil in a temperature range of 60–120 °C and moisture of 0.5, 1 and 2% (w/w). A linear relationship between one of the oil-soluble degradation by-products, i.e. methanol, and the number of ruptured 1,4-β-glycosidic bonds of cellulose, regardless of the type of paper (ordinary Kraft or thermally-upgraded (TU) Kraft paper), was established for the first time in this field. Ageing at 130 °C of model compounds of the Kraft paper constituents (α-cellulose, hemicellulose and lignin) and two cellulosic breakdown by-products (D-(+)-glucose and 1,6-anhydro-β-d-glucopyranose) confirmed that the α-cellulose degradation was mostly responsible for the presence of this molecule in the system. Furthermore, additional 130 °C-tests with six different papers and pressboard samples under a tight control of initial moisture indicated that at least one molecule of methanol is formed for each rupture of 1,4-β-glucosidic bond of the molecular chains. Stability tests showed that the ageing indicator is stable under the oxygen and temperature conditions of open-breathing transformers. The presence of methanol was detected in 94% of oil samples collected from over than 900 in-service pieces of equipment, confirming the potential for this application. Lastly, the tests have shown that oil-oxidation by-products and TU-nitrogenous agents modify the methanol partitioning coefficients in the paper/oil/air system, which makes their study essential over a range of field conditions encountered by power transformers. Results are presented and discussed in comparison with 2-furfuraldehyde, which is the current reference in the domain.     

低热-高压法制备PLGA多孔支架及其体外降解研究

采用低热-高压法制备了聚(dl-丙交酯／乙交酯)75／25(PLGA75／25)组织工程多孔支架。该方法避免了使用有机溶剂，支架的孔隙率在90％以上，孔径大小分布均匀。多孔支架经过酒精处理后，支架表面产生许多微小的凹陷；用藻酸钙改性处理后，支架形态保持良好。两种处理都使支架的压缩强度有所增大，亲水性增强。虽然孔隙率高的支架降解速率稍慢，但其体外降解规律基本一致：特性粘数争力学强度衰减快，而质量损失较慢，降解6周后，支架的质量损失仅为3％左右；体外降解3周后，支架的形态保持良好，可望在细胞移植争组织修复的早期发挥支撑作用。     

Structure and properties of the Nafion—polyaniline—palladium composite electrodes

Effect of conditions of deposition of palladium onto a composite polymeric film Nafion—polyaniline on the properties of the system thus obtained is studied. It is shown that the effect of the said conditions on the character of distribution of palladium in a polymer may be used when estimating electrocatalytic potentialities of such composites.Translated from Elektrokhimiya, Vol. 41, No. 2, 2005, pp. 213–218.Original Russian Text Copyright © 2005 by Andreev, Zolotarevskii.This revised version was published online in April 2005 with corrections to the article note and article title and cover date.     

Enzymatic degradation of highly phenolic lignin-based polymers (lignophenols)

Enzymatic degradation of two lignin-based polymers (lignophenols), lignocatechol and lignocresol, prepared by selectively grafting catechol and p-cresol to C_α positions of lignin, respectively, were carried out in aqueous organic solvents. Both lignophenols showed high reactivity in the peroxidase-catalyzed oxidation. Structural analyses by NMR spectroscopies revealed that the degraded lignophenols contained aliphatic chain content, which might be mainly formed in the reduction of the intermediate initially generated by the aromatic ring cleavage. Lower amount of aromatic units in the lignophenols after degraded by peroxidase also indicted the cleavage of aromatic rings. Due to the substitution of phenols at C_α positions of lignin, the degraded lignophenols did not have carbonyl structure, which was abundant in the biodegradation products of native lignin. The two lignophenols were also degraded by Rhus vernicifera laccase. But the degree of degradation was lower than that of the degradation by peroxidase, which might be due to the low activity of laccase on the lignin moieties in lignophenols.     

Gel permeation chromatographic characterization of sodium hyaluronate and its fractions prepared by ultrasonic degradation

Summary High-molecular-weight sodium hyaluronate isolated from rooster combs was degraded by ultrasonication. The molecular weight of hyaluronate and its polydispersity was determined by gel-permeation chromatography. During 75-min treatment the molecular weight value decreased from 1.39×10⁶ Da to 2.25×10⁵ Da while the polydispersity of the molecular weight increased from 1.29 to 2.36. The reciprocal value of the square of the hyaluronate's molecular weight was linearly proportional to the time of ultrasonication.     

Size exclusion chromatographic characterization of sodium hyaluronate fractions prepared by high energetic sonication

Summary A high molecular weight sodium hyaluronate isolated from rooster combs was degraded by ultrasonication. High-performance size exclusion chromatography allowed rapid and accurate determination of molecular weight parameters (M_z, M_w, M_n) and distributions. The time dependence of hyaluronan ultrasonication to the molecular characteristics of the polymer was investigated. A non-random nature of the degradation process was demonstrated and the reciprocal M_n value was found to be linearly proportional to the time of ultrasonication.