旋流泵全流道三维定常流场的数值模拟

本文在计算模型采用分块非结构化六面体网格的基础上,利用雷诺平均N-S方程,标准k-ε紊流模型,结合 SIMPLEC算法,数值模拟了旋流泵的内部流动,得到了旋流泵压力面、吸力面上的压力分布,同时也估算了叶轮的效率, 比较了旋流泵试验性能与数值模拟性能,有助于了解旋流泵的内部流动特性,指导旋流泵的水力设计。     

Spectroscopic and X-ray diffraction study of high Tc epitaxial YBCO thin films obtained by pulsed laser deposition

We report spectroscopic characterization of epitaxial YBCO thin films grown on LaAlO₃ by pulsed laser deposition. Raman spectroscopy and spectroscopic ellipsometry were used for film characterization and the results were correlated with X-ray diffraction measurements. The mentioned techniques allowed us to analyze crystallographic, micro-structural, and morphological properties of YBCO thin films. We also demonstrated that relatively low resolution Raman spectroscopy and spectroscopic ellipsometry are reliable techniques for a rapid and non-destructive characterization of epitaxial YBCO thin films.     

Latex particles bearing hydrophilic grafted hairs with controlled chain length and functionality synthesized by reversible addition–fragmentation chain transfer

A method is described for synthesizing latex particles with anchored hairs by the grafting of hydrophilic chains, synthesized by reversible addition–fragmentation chain transfer, onto functionalized latex particles. These have the potential to bind biologically active species. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1188–1195, 2003     

Effects of Moisture and Stresses on the Structure and Properties of Polyester Resin

The results of a complex study of structural changes in a cured Norpol 440 polyester resin under the action of damp environment and mechanical loading are presented. A considerable effect of absorbed moisture on the structure and some characteristics of the material is revealed by using thermophysical methods and X-ray diffractometry. The joint effect of moisture and mechanical stress is estimated by investigating the creep in stationary and nonstationary moisture conditions. The anisotropy of the material structure formed during creep is evaluated from the results of dilatometric measurements. It is found that the degree of anisotropy of the material after creep accompanied by moisture sorption is higher than that after creep in the conditions of moisture equilibrium with atmosphere. It is established that the aftercure and relaxation of the residual creep deformation come to an end at heating to 80-85°C. At a further rise in temperature and repeated heating, changes in the material structure are not observed.     

Multilayer optics for XUV spectral region: technology fabrication and applications

We present research investigations in the field of multilayer optics in X-ray and extreme ultra-violet ranges (XUV), aimed at the development of optical elements for applications in experiments in physics and in scientific instrumentation. We discuss normal incidence multilayer optics in the spectral region of “water window”, multilayer optics for collimation and focusing of hard X-ray, multilayer dispersing elements for X-ray spectroscopy of high-temperature plasma, multilayer dispersing elements for analysis of low Z-elements. Our research pays special attention to optimization of multilayer optics for projection EUV-lithography (ψ-13nm) and short period multilayer optics.     

环形燃烧室火焰简及旋流器流场计算

本文采用偏微分方程法生成贴体网格,在任意曲线坐标系下数值研究两种先进燃烧室火焰筒及其旋流器三维紊流流场。由于旋流器的形状复杂,本文采用型线定点法确定网格的边界。在非交错网格系下采用SIMPLE算法和混合差分格式对离散方程进行求解。计算结果表明计算方法合理,这计算程序进一步扩展,可用来预估环形燃烧室反应流流场。     

Influence of annealing and chain defects on the melting behaviour of poly(vinylidene fluoride)

The melting behaviour of poly(vinylidene fluoride) (PVDF) was investigated by differential scanning calorimetry (DSC) and small- and wide-angle X-ray scattering in order to study the influence of the chain defects content and of the temperature of annealing on the crystallization and melting behaviour.All the DSC scans show a double endotherm and the analysis of the data suggests that the low temperature endotherm is due to the melting of a population of thin lamellae, whose thickness increases during the annealing, but a high content of chain defects prevents the lamellar thickening and the main effect in this case is the crystallization of thin lamellae from a portion of polymer which did not crystallize during the quenching from the melt. Furthermore, the two melting endotherms, which are observed, can be partially ascribed to a melting-recrystallization process.Furthermore, stepwise isothermal cooling was performed in a differential scanning calorimeter followed by melting scans of fractionated PVDF samples to point out the possible presence of a series of endothermic peaks.     

Charge density study under high pressure

The experimental and analytical method of the high-pressure powder experiment at BL10XU, SPring-8, is described. There is no doubt that BL10XU must be one of the most appropriate beam lines for high pressure X-ray diffraction experiment taking advantage of third generation synchrotron source. As an example of the advanced charge density study under high pressure, the structural change of Cs₂Au₂Br₆ by applying pressure is studied by Rietveld/MEM analysis. It reveals that the structural change of Cs₂Au₂Br₆ by applying pressure occurs basically at electron level, such as valence state change and chemical bonding, which may be called the electronic phase transition.     

水平管外强化凝结传热的数值解

以Nusselt理论为基础,运用三维坐标建立了肋片侧面的冷凝传热模型,对肋片侧面的冷凝传热机理进行了分析,得出了肋片侧面表面传热系数的积分表达式。利用此法对水平环肋单管表面传热系数进行计算并将结果与传统解法进行比较。     

双预脉冲驱动X射线激光实验研究

 在“星光-Ⅱ”激光装置上进行了双预脉冲驱动类氖铬X射线激光实验，介绍了实验方法和实验结果，并对结果进行了简短讨论。由于目前“星光”装置输出能量较低，所进行的双预脉冲驱动未能显著提高X射线激光强度，改变预脉冲幅度时X射线激光强度也未有显著变化。利用MED103程序进行了模拟计算，其结果与实验结果一致。