油页岩的~(13)C-NMR特征及FLASHCHAIN热解模拟研究

采用固体13C-NMR核磁共振技术表征了甘肃窑街矿区油页岩的碳骨架结构,分析并计算了油母质团簇化学结构参数,包括团簇平均碳原子数、芳碳原子数、脂碳原子数及芳环数。在热重红外分析仪(TG-FTIR)上进行了油页岩的热解实验,得到了热解产物的生成规律。结合样品的团簇化学结构参数,采用基于油页岩结构的FLASHCHAIN模型模拟其热解产物的生成过程;模拟结果与TG-FITR实验数据符合较好,印证了模型预测的合理性。     

高硫煤镜质组热解过程中结构变化及有机硫形态变迁规律研究

用手选富集与离心分离相结合的方法,从两种全硫含量相近的新西兰煤（NXL;S_t,ad=1.84%）和山西煤（SX;S_t,ad=1.80%）中分离出高纯度镜质组。在高纯Ar气氛下,分别制备了300、500、700和1 000 ℃下的镜质组焦。用FT-IR研究了两种镜质组中的脂肪氢、芳香氢随温度的变化,结果表明,SX镜质组中脂肪氢的相对含量较高,在热解过程中活性高于同温度下的NXL镜质组;两种镜质组中的脂肪氢相对含量都随温度升高而降低,温度高于500 ℃时,SX镜质组中脂肪氢相对含量基本不变,当温度高于700 ℃时,NXL镜质组中的脂肪氢相对含量基本保持不变;热解过程芳香氢都表现出先增大后减小的趋势。用XPS研究了镜质组中的有机硫含量及形态随温度的变化,结果表明,SX镜质组中易分解的有机硫化物较多,在300 ℃以下即可分解完全;NXL镜质组中的有机硫化物分解完全在700 ℃左右,两种镜质组中的噻吩类硫的含量都随热解温度的升高而增加,砜类硫的含量随热解温度的升高而降低。     

灰中酸性成分对灰熔融温度的影响

搜集并统计了世界129种典型煤种、城市污水污泥及污泥/煤混烧灰样的灰成分及灰熔融特征温度等相关数据,研究灰中酸性成分SiO2、Al2O3、TiO2和P2O5对灰熔融特性的影响。结果表明,Al2O3是决定灰熔点的主要因素,酸性金属氧化物SiO2、Al2O3和TiO2形成的耐熔矿物质石英、偏高岭石、莫来石、金红石等可提高灰熔点。非金属氧化物P2O5与污泥和污泥/煤的灰熔点FT二次拟合很好且明显降低熔点,污泥灰中P2O5含量显著高于煤灰是导致其熔点明显低于煤的重要原因。     

FT-IR和SEM用于煤阶对煤催化加氢气化影响的研究

基于加压固定床反应器研究了不同煤阶的煤催化加氢气化效果,对比了煤阶对催化剂添加量、甲烷释放速率以及产品气组成的影响。原煤及气化残渣采用FT-IR和SEM进行表征分析。研究结果表明,不添加催化剂情况下,随着煤阶的升高原煤气化反应性降低,低阶煤的甲烷释放分为两个阶段;加入催化剂之后,3种煤中以神府烟煤的反应性最好,遵义无烟煤和云南褐煤反应性较差。SEM和FT-IR表征结果表明,高阶煤颗粒表面更加光滑、煤结构致密,而煤中的脂肪族结构以及芳香结构振动峰强度随煤阶的降低而升高,催化剂的加入使得脂肪结构吸收峰明显加强。这些差异导致不同煤样催化加氢气化反应活性不同。     

油页岩固定床热解反应器中内构件强化作用

在内构件(传热板和中心集气管)外热式固定床反应器中研究了油页岩热解产物生成特性,并与无内构件的相同常规固定床反应器内的油页岩热解行为对比,考察了两反应器中油页岩升温特性、热解产物分布、页岩油品质以及气体产物组成的变化规律.结果表明,内置传热板和中心集气管显著强化了反应器内的传热,相对于无内构件常规固定床反应器,料层升温速率提高了约2倍.对于依兰油页岩,其热解页岩油产率明显提高,最高达11.1 wt%(干燥基),明显高于无构件常规固定床反应器获得的页岩油产率.随着外加热炉温度的升高,内构件固定床反应器的页岩油产率逐渐增加,而无内构件常规固定床反应器的页岩油产率则明显降低.当外加热炉温度为1000℃时,前者页岩油产率是后者的2.3倍,并且内构件固定床反应器的热解水产率较低.两反应器中热解气产物组成相近,其H2与CH4之和占气体总量的70 vol%左右,热值为4406~5400 kcal/Nm3.     

Electrochemical Properties of Hollow‐Structured MnS–Carbon Nanocomposite Powders Prepared by a One‐Pot Spray Pyrolysis Process

Spherical, hollow MnS? C composite powders were prepared from a solution of manganese salt, thiourea, and sucrose by one‐pot spray pyrolysis. The MnS? C composite powders were generated by direct sulfidation of MnO with hydrogen sulfide gas generated in situ by decomposition of thiourea during spray pyrolysis. Sucrose, which is used as a carbon source material, plays a key role in the formation of the MnS? C composite powders by improving the reducing atmosphere around the powders. Dot‐mapping images of the composite powders demonstrated uniform distribution of the manganese, sulfur, and carbon components within the MnS? C composite powder. Fine crystals of MnS were uniformly mixed with carbon derived from polymerization and carbonization of sucrose. The carbon content of the MnS? C composite powders was 26 wt %. The discharge capacities of the MnS? C composite powders in the 2nd and 200th cycles were 863 and 967 mA h g^?1, respectively, at a current density of 1000 mA g^?1. The spherical and hollow morphology of the MnS? C composite powders was completely retained, even after 200 cycles. The enhanced cycling and rate performance of the MnS? C composite powders is ascribed to the structural stability of the composite powders.     

Preparation of Yolk‐Shell and Filled Co9S8 Microspheres and Comparison of their Electrochemical Properties

In this study, we report the first preparation of phase‐pure Co₉S₈ yolk–shell microspheres in a facile two‐step process and their improved electrochemical properties. Yolk–shell Co₃O₄ precursor microspheres are initially obtained by spray pyrolysis and are subsequently transformed into Co₉S₈ yolk–shell microspheres by simple sulfidation in the presence of thiourea as a sulfur source at 350 °C under a reducing atmosphere. For comparison, filled Co₉S₈ microspheres were also prepared using the same procedure but in the absence of sucrose during the spray pyrolysis. The prepared yolk–shell Co₉S₈ microspheres exhibited a Brunauer–Emmett–Teller (BET) specific surface area of 18 m² g^?1 with a mean pore size of 16 nm. The yolk–shell Co₉S₈ microspheres have initial discharge and charge capacities of 1008 and 767 mA h g^?1 at a current density of 1000 mA g^?1, respectively, while the filled Co₉S₈ microspheres have initial discharge and charge capacities of 838 and 638 mA h g^?1, respectively. After 100 cycles, the discharge capacities of the yolk–shell and filled microspheres are 634 and 434 mA h g^?1, respectively, and the corresponding capacity retentions after the first cycle are 82 % and 66 %.     

Flame Spray Pyrolysis for Finding Multicomponent Nanomaterials with Superior Electrochemical Properties in the CoOx‐FeOx System for Use in Lithium‐Ion Batteries

High‐temperature flame spray pyrolysis is employed for finding highly efficient nanomaterials for use in lithium‐ion batteries. CoO_x‐FeO_x nanopowders with various compositions are prepared by one‐pot high‐temperature flame spray pyrolysis. The Co and Fe components are uniformly distributed over the CoO_x‐FeO_x composite powders, irrespective of the Co/Fe mole ratio. The Co‐rich CoO_x‐FeO_x composite powders with Co/Fe mole ratios of 3:1 and 2:1 have mixed crystal structures with CoFe₂O₄ and Co₃O₄ phases. However, Co‐substituted magnetite composite powders prepared from spray solutions with Co and Fe components in mole ratios of 1:3, 1:2, and 1:1 have a single phase. Multicomponent CoO_x‐FeO_x powders with a Co/Fe mole ratio of 2:1 and a mixed crystal structure with Co₃O₄ and CoFe₂O₄ phases show high initial capacities and good cycling performance. The stable reversible discharge capacities of the composite powders with a Co/Fe mole ratio of 2:1 decrease from 1165 to 820 mA h g^?1 as the current density is increased from 500 to 5000 mA g^?1; however, the discharge capacity again increases to 1310 mA h g^?1 as the current density is restored to 500 mA g^?1.     

Synthesis and Pyrolysis of Fullerenol-stabilized Pt Nanocolloids as a unique Approach to Pt-doped Carbon

An aqueous colloidal dispersion of Pt nanoparticles (NPs) stabilized by fullerenol C₆₀(OH)₁₂ (Pt:C₆₀(OH)₁₂) was successfully synthesized via liquid-phase chemical reduction. The subsequent pyrolysis of Pt:C₆₀(OH)₁₂ at different temperatures was conducted to afford Pt-doped carbon with different chemical compositions (Pt:C60ⁿ). X-ray absorption spectroscopy (XAS) and Infrared (IR) absorption spectroscopy and thermogravimetric measurements revealed that the thus-prepared nanocomposite consists of Pt NPs and high valent Pt-C₆₀(OH)₁₂ complex. One distinct feature of C₆₀(OH)₁₂ matrix as catalyst support is the suppression of size growth of Pt NPs during the pyrolysis up to 300 °C. Electrochemical experiments using cyclic voltammetry (CV) and linear sweep voltammetry (LSV) were performed to find that Pt:C60³⁰⁰ (pyrolyzed at 300 °C) exhibited higher activity than others, that was attributed to the π-extended feature of the as-obtained carbon.