桦甸油页岩热解特性的研究

在热分析仪上进行了桦甸油页岩的热解特性研究,升温速率分别为10℃/min、20℃/min、30℃/min和40℃/min,终温为900℃。实验表明油页岩的热解是分两步进行的。在低温段主要是油页岩中可挥发性的气体溢出引起热解失重;高温段则主要是一些有机质、固定碳的热解过程。低温段的热解是主要的,它基本上热解掉了油页岩重量的15％－27％左右,油页岩挥发分含量很高且具有集中析出的特性,在400℃－530℃区间内可挥发物质迅速热解守比,其在高温段的热解产率很小,只有总重量的10％左右。随着升温速率的增加低温段的高温段热解的区分更加明显,且使油页岩的热解产率提高。文中给出了不同升温速率下的桦甸油页岩热解特性数据和化学反应动力学参数。     

油页岩热解挥发分产物二次反应对油气收率与组成的影响

采用两段反应器对油页岩热解释放的一次挥发分产物进行不同热态条件下的二次反应特性研究,考察第二段温度、气氛与停留时间对油气收率及品质的影响。研究结果表明,转化温度对油气产率的影响最明显,在优化第一段热解反应条件的基础上,当反应器第二段温度由600℃提高到650℃时,油页岩热解油产率下降15%(质量分数,下同),气体产率增加约20%。与氮气气氛相比,水蒸气作为第二段反应气氛能够提高液体油品收率约5%,并且热解油主要集中在馏程350℃的汽柴油馏分。结合GC-MS分析表明,停留时间0-3 s二次反应主要为裂解过程,水蒸气能够提高油品中芳烃含量,同时抑制芳烃缩聚;3-5 s二次反应主要为缩聚过程,焦炭生成量增加,汽柴油馏分收率保持稳定,VGO馏分油收率下降约30%。     

矿物质对桦甸油页岩热解产物影响特性

对桦甸油页岩进行逐级酸洗并对原样及各级酸洗样品的热解产物进行了碳平衡计算以及气相色谱和傅里叶红外光谱实验,得到了矿物质对油页岩热解不凝性气体、半焦以及页岩油的影响特性。结果表明,碳酸盐可以促进有机碳和氢向页岩油中转化,而硅酸盐对有机碳和氢向页岩油中转化具有抑制作用,碳酸盐和硅酸盐均可以使得页岩油中氢碳原子比降低。碳酸盐促进了油页岩热解产油并抑制了干酪根向不凝气分解转化,而硅酸盐抑制了油页岩热解产油但对干酪根向不凝气的分解转化具有促进作用。碳酸盐和硅酸盐均可以促进热解不凝气中CO_2和H_2的生成,而对CO的生成具有抑制作用,碳酸盐可以抑制热解不凝气中碳氢化合物的生成,而硅酸盐对其生成具有促进作用。碳酸盐和硅酸盐均可以使得页岩油中脂肪链长度变短及异构化程度变大,并能够提高干酪根热解产物的芳构化程度。     

煤在合成气、氢气和氮气气氛下的热解研究

采用固定床反应器，在合成气气氛下对中国寻甸褐煤、蒙古Shiveeovoo褐煤和Khoot油页岩进行了热解研究。升温速率10 ℃/min，褐煤热解温度400 ℃～800 ℃，油页岩热解温度300 ℃~600 ℃，研究结果与氢气和氮气气氛下的热解进行了比较。结果表明,与加压热解不同，褐煤在不同气氛下常压热解半焦和焦油收率差别不大，但对油页岩，合成气和氢气气氛下热解焦油收率高于氮气，气体收率低于氮气。黄铁矿硫在不同气氛下热解均极易脱除，并部分转化为有机硫。油页岩的总硫脱除率远低于褐煤，与油页岩的高灰分含量有关。与氮气甚至氢气相比，合成气下寻甸褐煤的高总硫脱除率和低有机硫含量与合成气中的CO有关。但CO在油页岩热解脱硫中不起作用，也与油页岩高灰分含量有关。研究结果也表明合成气可代替氢气进行加氢热解。     

污泥与醋糟共热解特性及碱金属迁移规律

分别采用热重分析仪、真空固定床反应器和原子吸收光谱研究了污泥与醋糟共热解过程中反应动力学、产物分布和碱金属迁移行为,探究了协同效应及碱金属迁移规律。结果表明,两者共热解过程中存在明显协同效应;与理论计算相比,混合物分解所需的活化能下降了35.38%～29.49%,脱挥发指数比计算低3.5×10-8。协同效应导致气体产率增加,生物炭、液体产率降低;醋糟的存在加速了污泥的脱挥发分析出,提高了气体产物中合成气含量,加大了生物炭中大芳香环的裂解反应,使生物油中酚类和酯类物质含量明显增加;热解终止时,碱金属元素析出量达到79.19%～86.73%。     

FLASHCHAIN模型应用于汪清油页岩热解研究

采用~(13)C-NMR技术表征出汪清三个矿区油页岩的碳原子化学结构,并获得碳骨架结构的12个重要参数。利用热重和傅里叶红外联用技术(TG-FTIR)得出了在50℃/min升温速率和热解终温600℃下油页岩热解时轻质气体的生成规律。采用基于燃料化学结构的FLASHCHAIN模型对热解产物的析出进行了模拟,并与实验结果相比较。结果表明,FLASHCHAIN模型用来模拟汪清油页岩热解时,在520℃之前有较好的效果,当温度高于520℃时,由于二次热解反应及页岩中矿物质分解对热解过程的影响,导致模型的预测值与实验值存在一定的误差,且随着温度的升高两者之间的误差也随之加大。     

循环流化床内废轮胎的热解油化

介绍了以循环流化床反应器为主体的废轮胎热解油化装置,实验过程,实验结果及分析。通过评价热解条件对气体成分及油、碳和气产物产率的影响,以及热解油品的成分分析,得出如下结论：（１）较高的温度和较好的停贸时间会生成过多的不凝气（主要成分为ＣＨ４、Ｈ２,Ｃ２ＨＶ和ＣＯ等）,降低油的产率,过低的温度和加热速率导致严重的碳化,同样会降低油产率。（２）热解油品的组成成分非常复杂,芳烃占了很大比例,其次是烷烃和非     

固定床中纤维素热解及其焦油裂解机理研究

研究了500~900℃条件下微晶纤维素在固定床中的热解过程;分别采用气质联用(GC-MS)和气相色谱分析了热解过程中生成的焦油和不可凝气体。结果表明,随热解温度升高,焦油产率减少、气体产率升高、焦产率略微下降,同时CO、CH4和H2的产率明显升高,而CO2的产率变化不明显。焦油主要由二次反应产生,不可凝气体则由一次热解产物和二次热解产物共同产生。使用Gaussian 09软件对热解过程进行了模拟,发现纤维素分子在热解过程中首先分解为纤维素单体,然后纤维素单体上的羟基官能团优先脱除,生成的中间产物重组生成焦油。随热解温度升高,焦油中醚、醇、酸等化合物分解成自由基,自由基间发生重组、结合,导致烯烃和炔烃增多以及不可凝气体含量的升高。     

生物质铁盐催化加氢热解产生生物油与气态烃的研究

利用加压固定床反应器进行了松木催化加氢热解实验(终温600-700℃、氢压5.0 MPa),考察了硝酸铁和硫酸亚铁两种铁盐对热解产物产率及分布的影响。研究发现,Fe(NO_3)_3能够显著促进生物炭加氢生成甲烷,碳转化率高达97.4%,CH_4产率达21.2%,无水生物油产率为32.8%(产率基准均为干燥无灰生物质),生物油中含氧量降低,轻质芳烃产率增加,其中,苯、甲苯和二甲苯(BTX)产率为2.6%。而FeSO_4迥异于Fe(NO_3)_3,具有抑制气态烃和生物油生成的作用。机理研究表明,Fe(NO_3)_3在加氢过程中主要形成α-Fe,并促使生物炭形成无定型和多孔结构,从而有利于其加氢生成甲烷,而FeSO_4则部分转化为Fe_2S_3,由此可致使铁催化剂失活。     

水介质条件下油页岩热解机理研究

利用高压釜反应装置,对柳树河油页岩进行了饱和水和不饱和水介质条件下的热压模拟实验,研究了两种条件下油页岩热解产物(气体、油和热沥青)的生成机理.实验结果表明,在油页岩的热解过程中,同时经历自由基反应和碳正离子反应.水在高温的物化性质较在常温常压时发生了巨大的变化,具有酸催化剂和碱催化剂的作用,促使按碳正离子机理进行反应...     

Coal pyrolysis in a fluidized bed reactor simulating the process conditions of coal topping in CFB boiler

Simulating the conditions of pyrolytic topping in a fluidized bed reactor integrated into a CFB boiler, the study was devoted to the reaction fundamentals of coal pyrolysis in terms of the production characteristics of pyrolysis oil in fluidized bed reactors, including pyrolysis oil yield, required reaction time and the chemical species presented in the pyrolysis oil. The results demonstrated that the maximal pyrolysis oil yield occurred on conditions of 873 K, with a reaction time of 3 min and in a reaction atmosphere gas simulating the composition of pyrolysis gas. Adding H₂ and CO₂ into the reaction atmosphere decreased the pyrolysis oil yield, while the oil yield increased with increasing the CO and CH₄ contents in the atmosphere. TG-FTIR analysis was conducted to reveal the effects of reaction atmosphere on the chemical species present in the pyrolysis oil. The results clarified that the pyrolysis oil yield reached its maximum when the simulated pyrolysis gas was the reaction atmosphere, but there were slightly fewer volatile matters in the pyrolysis oil than the oil generated in the N₂ atmosphere. All of these results are expected not only to reveal the composition characteristics of the pyrolysis oil from different conditions of the coal topping process but also to optimize the pyrolysis conditions in terms of maximizing the light pyrolysis oil yield and quality.     

Gas Evolution from the Pyrolysis of Jordan Oil Shale in A Fixed-bed Reactor

Jordan oil shale from El-Lajjun deposit was pyrolysed in a fixed-bed pyrolysis reactor and the influence of the pyrolysis temperature between 400 to 620°C and the influence of the pyrolysis atmosphere using nitrogen and nitrogen/steam on the product yield and gas composition were investigated. The gases analysed were H₂, CO, CO₂ and hydrocarbons from C₁ to C₄. The results showed for both nitrogen and nitrogen/steam that increase the pyrolysis bed temperature from 400 to 520°C resulted in a significant increase in the oil yield, after which temperature the oil yield decreased. The alkene/alkane ratio including ethene/ethane, propene/propane, and butene/butane ratios, can be used as an indication of pyrolysis temperature and the magnitude of cracking reactions. Increasing alkene/alkane ratio occurring with increasing pyrolysis temperature. The alkene/alkane ratio for nitrogen/steam pyrolysis atmosphere was lower than the one found under nitrogen atmosphere. This revised version was published online in July 2006 with corrections to the Cover Date.     

固体热载体热解霍林河褐煤实验研究

在处理量为10kg/h的粉煤-固体热载体移动床实验装置上,以循环灰为热载体对其进行了热解特性评价实验.考察了热解温度(460℃~610℃)、反应时间(6min~8min)及煤粒粒径对热解产物产率和组成的影响.结果表明,随着热解温度的升高,气体产率增大;焦油产率在520℃时达到最大值4.94%.热解煤气的热值为19.80...     

热预处理影响褐煤热解行为研究

采用固定床反应器研究了不同气氛热预处理对内蒙胜利褐煤结构的改变,及其对后续热解行为的影响。结果表明,与原煤相比,热预处理后煤中羟基含量和芳香氢与脂肪氢的比减少,脂肪氢的相对含量增加。与未经处理的煤热解相比,N2、N2+O2、CO2气氛下热预处理后热解水收率下降,热解气收率增加,热解气中CO2含量增高,导致高位热值下降。过热水蒸气热预处理后,焦油质量收率提高3～4个百分点。热解焦油组成的变化与预处理气氛、温度密切相关,过热水蒸气200℃下预处理使得焦油中轻质组分的含量(沸点低于360℃的馏分)比原煤焦油提高了约27个百分点;水蒸气和模拟烟气混合气氛下在200℃及250℃预处理后,其热解焦油中轻油和酚油含量分别提高约60和42个百分点。     

Influence of residence time and catalyst regeneration on the pyrolysis–zeolite catalysis of oil shale

Oil shale from the Kark region of Pakistan has been pyrolysed in a fixed bed batch reactor and the properties of the derived shale oil determined. The reactor system was then modified to incorporate a second reactor where the derived vapours from oil shale pyrolysis were passed directly to the second reactor containing zeolite ZSM-5 catalyst. The influence of the process parameters of vapour residence time (VRT) over the catalyst and the regeneration of the catalyst were examined. The yield and composition of the derived gases before and after catalysis were determined. In addition, the yield and composition of the derived oil in terms of total nitrogen and sulphur content and the content of aromatic hydrocarbons in the oils was investigated. The results showed that the yield of oil after catalysis was reduced with a consequent higher yield of gases and formation of coke on the catalyst. The main gases from the pyrolysis of oil shales were CO₂, CO, H₂, CH₄, C₂H₄, C₂H₆ and C₃H₆, C₃H₈ and minor concentrations of other hydrocarbon gases. The main role of catalysis was to convert the long chain alkanes and alkenes in the oil to lower molecular weight, short chain, alkyl substituted and iso species and high concentrations of aromatic hydrocarbons. Total nitrogen and sulphur contents in the oils were markedly reduced after catalysis. This reduction was reflected in the reduced concentration of nitrogen and sulphur containing aromatic hydrocarbons. The influence of longer VRTs was to increase the formation of aromatic hydrocarbons, reduce the nitrogen, and sulphur compounds in the oils. The influence of catalyst regeneration, involving five regenerations was not significant on the yield and composition of the derived catalytically upgraded oils.     

颗粒油页岩燃烧及含硫杂质的转化

对抚顺、茂名及约旦颗粒油页岩在热重分析仪(TGA)上进行了燃烧研究,考察了抚顺及茂名颗粒油页岩在模拟流化床快速升温条件下的燃烧性能并与恒温燃烧作了对比。结果表明,升温速度提高时,失重率(即燃烧速率)明显加剧。文中还对含碳酸盐及含硫量高的约旦颗粒油页岩在燃烧过程中硫的转化进行了研究。X射线衍射分析表明,它在燃烧过程中有较强的自脱硫能力。通过对该油页岩燃烧过程中热量的有效利用问题的讨论,认为在流化床内燃烧此类含碳酸盐较高的油页岩时宜采用短停留时间的炉型。     

Thermal self-sustainability of biochar production by pyrolysis

The pyrolysis of several agricultural and biofuel production residues (grape residues, sugarcane residues, dried distiller's grain, palm oil residues, apple pomace and forestry residue) has been carried out in a pilot bubbling fluidized bed pyrolyzer operating under a range of temperature from 300 to 600 °C and two vapor residence times (2 and 5 s), with the aim of determining their pyrolysis behavior including products yields and heat balance. The composition of the product gases was determined, from which their heating value was calculated. The liquid bio-oil was recovered with cyclonic condensers. The thermal sustainability of the pyrolysis process was estimated by considering the energy contribution of the product gases and of the liquid bio-oil in relation to the pyrolysis heat requirements. The most promising biomass feedstocks for the sustainable production of biochar were indentified. Furthermore, this study presented the char yield in relation to the excess heat that could be obtained by combusting the gas and bio-oil coproducts of biochar production, as functions of pyrolysis temperature and vapor residence time.     

扎赉特旗油砂在氮气气氛下的热解制油研究

油砂是一种含有沥青或其他重质石油的沉积岩，主要用于提取油砂沥青，以生产合成原油。中国拥有相当数量的油砂资源，目前还未开采，仅处于初步研究阶段。加拿大在20世纪初期就展开了油砂的开采及制油研究工作，并于20世纪70年代由加拿大合成油公司实现了工业化生产。油砂生产的沥青和合成油已占其石油总产量的1／4以上。