制备方法对MoO_3／ZrO_2结构的影响及MoO_3／ZrO_2固体超强酸的结构特征 Ⅰ．ZrO_2的形态与样品比表面的研究

ＸＲＤ，ＤＴＡ，比表面测定等结果表明，制备方法对ＭｏＯ３／ＺｒＯ２结构有决定性影响．仲钼酸铵浸渍仅经干燥的Ｚｒ（ＯＨ）４再经高温焙烧所得团体超强酸ＭｏＯ３／ＺｒＯ２（Ⅰ）与浸渍晶态ＺｒＯ２所得部分氧化催化剂ＭｏＯ３／ＺｒＯ２（Ⅱ）的载体形态有明显不同．（１）ＭｏＯ３／ＺｒＯ２（Ⅰ）的比表面数倍于ＭｏＯ３／ＺｒＯ２（Ⅱ）；（２）ＭｏＯ３含量增加时，ＭｏＯ３／ＺｒＯ２（Ⅰ）的比表面逐步增大至一极大值再缓缓下降，而ＭｏＯ３／ＺｒＯ２（Ⅱ）的比表面随ＭｏＯ３含量增加而单调下降；（３）在ＭｏＯ３／ＺｒＯ２（Ⅰ）中，ＺｒＯ２以介稳四方相存在，而在ＭｏＯ３／ＺｒＯ２（Ⅱ）中则是稳定的单斜相．在此基础上研究了事先引入的活性组分在载体织构形成过程中的作用，包括延迟ＺｒＯ２晶化，阻碍晶粒长大及与之相关的相变等，并讨论了ＭｏＯ３／ＺｒＯ２（Ⅰ）中ＭｏＯ３最佳含量的科学含义．     

Stopped-flow injection analysis. The influence of diffusion on dispersion of normal and reverse flow injection

A relationship is derived to enable the comparison of the dispersion heights of normal and reverse flow injection analysis (FIA). A single channel flow system is employed in the absence of a chemical reaction. The stopped-flow injection method is used to probe the influence of molecular diffusion on the overall dispersion of normal and reverse FIA, which appeared to demonstrate fundamentally different diffusion behaviors. Small discrepancies are observed between the dispersion heights, which are enhanced by the stopped-flow period, especially when unmatched matrix ionic compositions of the indicator and counter solutions were involved. For these conditions, the diffusion flux rate is enhanced considerably, displaying a peak, in addition to the transient, for both methods. The influence of diffusion on the dispersion characteristics of normal and reverse FIA is discussed theoretically. Diffusion in the proposed model is postulated to oppose dispersion by convection. The latter initiates concentration gradients in the injection zone and propagates it with flow time over the dispersion zone profile. The diffusion flux then reacts in order to confine the indicator dispersion for normal FIA and to enhance it for reverse FIA. This model is consistent with the experimental results and accounts for most of the phenomena encountered. Probably owing to the influence of secondary flow phenomena, the use of coiled tubes has suppressed the effects of diffusion on the overall dispersion behavior.Part of the experimental work was performed at IMI Institute for Research and Development, Haifa, Israel.     

A family of multiderivative methods for the numerical solution of the Schrödinger equation

A family of multiderivative methods with minimal phase-lag are introduced in this paper, for the numerical solution of the Schrödinger equation. The methods are called multiderivative since uses derivatives of order two, four or six. Numerical application of the new obtained methods to the Schrödinger equation shows their efficiency compared with other similar well known methods of the literature.Active Member of the European Academy of Sciences and Arts     

Unusual features of micellar diffusion

Diffusion coefficients of tetradecyltrimethylammonium bromide in aqueous solutions have been determined at 25, 95 and 135 °C using the Taylor dispersion technique. The diffusion coefficient exhibits a minimum at a surfactant concentration above the critical micelle concentration (CMC). The results are interpreted in terms of electrostatic coupling and rapid exchange between micelle, surfactant monomer and counterions.     

Increased oxygen transfer in a yeast fermentation using a microbubble dispersion

A microbubble dispersion (MBD) was used to supply oxygen for aerobic fermentations in a standard 2 L stirred tank fermenter. The microbubble dispersion was formed using only surfactants produced naturally. Growth rates ofSaccharomyces cerevisiae cultures were found to be equal or greater with MBD sparging than with gas sparging. The oxygen transfer coefficent with MBD sparging was found to be 190/h and independent of impeller speed from 100–580 rpm. The oxygen transfer coefficient with air sparging rose from 55 to 132/h over the same range of impeller speeds. Power requirements for the fermenter systems were estimated.     

NixB/沸石催化剂的分散性和反应性

用晶内形成法制备了Ni_xB/沸石催化剂,用饱和氢化学吸附法结合TEM方法考察了负载金属的分散性,并研究了其己环烷脱氢反应性。结果表明,Ni_xB/沸石样品上负载金属的分散性高,金属粒径分布也相对集中;金属负载量、载体结构和性质以及Ni_xB的制备条件对负载金属的分散性有明显影响。Ni_xB/沸石样品呈现较好的环己烷脱氢反应性。     

Complications in the Use of the Taylor Dispersion Method for Ternary Diffusion Measurements: Methanol + Acetone + Water Mixtures

The Taylor dispersion technique is used to measure the ternary mutual diffusion coefficients of aqueous nonelectrolyte solutions at 25°C. The dispersion of the injected solutes is recorded by a differential refractometer and an ultraviolet-visible detector. The diffusion coefficients are calculated directly by fitting the theoretical dispersion equations to about six experimental curves simultaneously. If the ternary diffusion effects in the measured dispersion profiles are not confused by the inaccuracy of the experimental method or an unfavorable relative detector sensitivity, the diffusion coefficients are precise. For the system methanol + acetone + water, it is shown that the Taylor dispersion method is unsuitable for the determination of all the diffusion coefficients if the methanol mole fraction is less than 0.45 or the acetone mole fraction if more than 0.001.     

Highly crosslinked micron-range polymer microspheres by dispersion polymerization of divinylbenzene

Narrow disperse microparticles are formed by dispersion polymerization of commercial divinylbenzene in acetonitrile or ethanol solution in the presence of 2,2′-azobis(2-methylpropionitrile) initiator and polyvinylpyrrolidone stabilizer. The particles have average diameters between 1 and 9 μm depending on monomer concentration, solvent, and temperature. While the smaller particles are relatively smooth, surface texture increases with diameter to give popcorn shapes at 9 μm diameter. High crosslinker concentration is shown to be essential for particle formation. © 1993 John Wiley & Sons, Inc.     

Laponite clay in homopolymer and tri-block copolymer matrices

Macromolecule/laponite nanomaterials were studied by DSC and X-ray diffraction techniques. The matrices are poly(ethylene) glycols at various molecular masses and poly(ethylene oxides)-poly(propylene oxides)-poly(ethylene oxides) tri-block copolymers. The latter were tuned by modulating the molecular masses, at constant hydrophilic/hydrophobic ratio, and the hydrophilicity. For all the investigated systems, the enthalpy of melting (ΔH _m) is nearly constant up to a given composition thereafter it increases monotonically reaching the value of the pure macromolecule. We proposed a model to interpret the DSC data. Briefly, it was invoked a mechanism of interaction following which some segments of the adsorbed macromolecule are anchored to the laponite (RD) particles and the remaining segments are radiating away from the surface. The portion of the macromolecule in contact with RD does not contribute to ΔH _m whereas that radiating away from the clay does. Once that the RD surface is saturated, the excess of the macromolecule behaves like the pure one. The proposed model allowed to compute successfully the ΔH _m values. The X-ray diffraction experiments ruled out the polymer intercalation between the silicate sheets.     

氧化物表面单层改性对SnO2超微粒子热稳定性的影响

研究了氧化物在气敏材料二氧化锡超细粉表面的分散行为及分散量的二氧化锡热稳定性的影响,结果表明,氧化铜,氧化镍,氧化铋和氧化锌在二氧化锡表面均能单层分散,分散阈值均与按密置单层模型计算的最大分散容量相符,负载二氧锡的表面覆盖度与其稳定性之间有很好的对应关系,单层覆盖率达到一定程度二氧化锡高温烧结便可基本得到抑制。