锐钛矿二氧化钛超细纳米晶的三声子互作用

本文通过对粒径为2.2-25.5nm的锐钛矿二氧化钛超细纳米晶在83-293 K温度范围内的变温拉曼光谱的研究,得到了三声子互作用对拉曼频率和线宽的贡献随粒径的变化关系。结果表明锐钛矿二氧化钛超细纳米晶的三声子相互作用随粒径减小而加强。     

光码分多址系统中光学相关接收机判决阈值的分析

介绍了光码分多址系统中常用地址码（一维扩时码、二维码和三维码）的特点，并对它们各自的互相关均值和方差进行了理论分析。基于非相干光码分多址系统中光学相关接收机的基本原理，结合不同的用户地址码，对系统误码率性能进行了分析，得到了接收机最佳判决阈值与地址码基本特性参数和系统同时用户数间的关系。最后，给出了数值仿真结果。结果表明，对于采用特定地址码的光码分多址系统，只有选择合适的接收机判决阈值，系统的误码率性能才能达到最佳。研究结果对光码分多址系统中接收机判决阈值的选取具有一定的参考作用。     

非傍轴平顶高斯光束M2因子两种定义的比较研究

基于功率密度的二阶矩方法，推导出了非傍轴平顶高斯(FG)光束束宽和远场发散角的解析表达式.研究表明，当w0/λ→0时，远场发散角趋于渐近值θmax=63.435°，与阶数无关.使用非傍轴高斯光束代替傍轴高斯光束作为理想光束，研究了非傍轴FG光束的M2因子，并与传统定义的M2因子作了比较.在非傍轴范畴，非傍轴FG光束的M2因子不仅与阶数N有关，而且与w0/λ有关.按照定义，当w0/λ→0时，非傍轴FG光束的M2因子不等于0，对阶数N=1, 2, 3时，M2因子分别趋于0.913,0.882和0.886.当N→∞时，M2因子取最小值M2min=0.816.     

Growth studies of m-GaN layers on LiAlO2 by MOCVD

This paper reports that the m-plane GaN layer is grown on （200）-plane LiAlO2 substrate by metal-organic chemical wpour deposition （MOCVD） method. Tetragonal-shaped crystallites appear at the smooth surface. Raman measurement illuminates the compressive stress in the layer which is released with increasing the layer＇s thickness. The high transmittance （80%）, sharp band edge and excitonic absorption peak show that the GaN layer has good optical quality. The donor acceptor pair emission peak located at -3.41 eV with full-width at half maximum of 120 meV and no yellow peaks in the photoluminescence spectra partially show that no Li incorporated into GaN layer from the LiAlO2 substrate.     

Luminescence investigations of the GaP-based dilute nitride Ga(NAsP) material system

Multi-quantum well heterostructures (MQWHs) of the novel Ga(NAsP)/GaP material system have been grown, pseudomorphically strained to GaP-substrate. The crystalline perfection is verified by transmission electron microscopy (TEM). For As-concentrations in excess of about 70%, a direct band structure and adequate luminescence efficiency for laser device application is observed. Temperature-dependent photoluminescence (PL) investigations show the influence of carrier localisation and non-radiative recombination processes typical for dilute nitride materials. With rising N content in the active material, the emission wavelength shifts towards longer wavelength, leading to Ga(NAs)/GaP MQW structures with photon energies below the indirect band gap of silicon (Si). At the same time the luminescence intensity drops due to an increase in non-radiative carrier traps and/or structural degradation.     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.     

一种新型可调谐锁模光纤激光器

利用法布里-珀罗腔的激光二极管作为调制器件，实现环形腔光纤激光器的主动锁模。并利用法布里-珀罗腔的激光二极管的多纵模特性，把激光二极管当作一梳状滤波器，通过偏振控制器来调整入射到激光二极管内光的偏振态，同时均衡腔内增益，得到波长大范围可调谐的锁模激光，其脉冲宽度约为48ps，脉冲重复速率2GHz。     

约束层对激光驱动冲击波压力影响机理的理论研究

针对刚性约束层、柔性约束层以及液体约束层，从激光诱导冲击波阵面状态、汽化物(包括气体和等离子体)扩散以及冲击波的反射进行分析，发现对于脉宽小于冲击波通过汽化物层的时间间隔的短脉冲激光，约束层并不能直接提高冲击波的冲量，而对于脉宽大于冲击波通过汽化层时间间隔的激光，其增强冲击效果是通过约束汽化物的扩散，提高压力幅值和由于冲击波在约束层与工件表面的多次反射而延长对工件的作用时间来实现的.刚性约束层能最大地增加冲击冲量，而柔性约束层和液体约束层的主要优点是其形状可与非平面形工件表面符合. 关键词： 激光 约束层 扩散 反射波     

激光二极管反馈干涉的实验观测

利用LabView软件虚拟示波器和信号源,观测了激光二极管反馈干涉实验现象．实验证明反馈回激光二极管的光的入射方向和入射光强以及信号处理电路的带宽,对反馈干涉信号有很大的影响．     

基于旋转描述的三维几何造型方法

提出了一种能用凸四边形表示并可作平面展开的三维实体造型的设计方法。该方法用旋转描述表把二维平面展开图和三维实体联系起来，模拟人工折叠过程，由二维平面展开图逐次旋转变换完成三维造型重建。造型重建后，再通过纹理映射将平面设计图案映射到实体的各个面上，完成对实体着色渲染，生成具有真实感的三维实体。