管肋式辐射器排热特性的数值分析与优化设计

为得到按单面辐射方式布置的管肋式空间辐射器的排热特性，建立了相应的数学模型．采用数值模拟方法分析了管内流体温度、肋片几何尺寸和等效热沉温度对辐射器排热特性的影响，得到了不同参数值下辐射器单位面积排热量以及特定参数范围内的辐射器肋片最佳宽度和肋片效率．数值模拟结果对辐射器的工程结构设计以及空间站热管理方案的优化分析具有一定的参考价值．     

胶体颗粒大小的分布——Ⅱ.物理显影中胶体催化剂颗粒大小的分布函数

本文用对数正态分布对物理显影中常用的Au、Ag及Ag_2s胶体催化剂的颗粒大小的实验分布进行了拟合。理论分布与实验分布的比较表明:本实验条件下制备的十二组胶体溶液其颗粒大小都服从了对数正态分布,并且不依赖于胶体的组成、大小及制备方法。因此,它们很可能遵从了同样的成核成长规律。     

Monte Carlo simulation of grain growth in polycrystalline materials

Understanding the kinetics of grain growth, under the influence of second phase (such as impurities, voids and bubbles) is fundamental to advances in the control of microstructural evolution. As a precursor to this objective, we have investigated the grain growth kinetics in a polycrystalline material using a standard Q-state Potts’ model under Monte Carlo settings. Based on physical reasoning, new modifications are suggested to circumvent some of the disadvantages in the basic Potts model. The efficacy of these modifications vis-à-vis the basic model is verified. The influence of second phase particles on the impurity loaded grain boundaries is investigated for the study of grain growth kinetics.     

Numerical Analysis and Simulation Analysis for Space‐Time Data

Spatio temporal dynamics of the positive column of a dc neon glow discharge is studied and investigated experimentally and theoretically. Spatio temporal analysis by means of biorthogonal decomposition method (BOD) gives insights into the mechanism of irregularity and can be employed for characterization of spatio‐ temporal complexity. In the weak nonlinear region, the wave dynamics is approximated by an amplitude equation of the Ginzburg‐Landau equation (CGLE) with complex coefficients and an additional integral term based on a fluid model. In the present work we deal with irregular spatio‐temporal data. A comparison between the numerical analysis of the experimental data and simulation results are studied. A good agreement between the dynamical behaviour for experimental space‐time data and theoretical simulation space‐time results was obtained. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A tentative approach to the direct simulation of drag reduction by polymers

An efficient technique for drag reduction uses dilute solutions of a few p.p.m. of polymers. A possible reduction in drag of up to 80% is achieved. Several experimental observations have been made which tend to indicate that the polymers modify the turbulence structures within the buffer layer. Flow visualisations have shown that the changes consist of a weakening of the strength of the streamwise vortices. Existing literature reveals no attempts of numerical simulation of this phenomenon. In this paper an approach is pursued by using a constitutive equation which relates the elongation viscosity to the local properties of the flow. According to this model this viscosity is large in zones where the amount of strain rate is greater than the amount of vorticity, and is zero when the vorticity exceeds the strain rate. Simulations have been performed in a “minimal channel” to give good resolution with a limited number of grid points. The accuracy of the method is tested by comparison with the results of other techniques. For simulations with polymers, quantitative comparisons cannot be made, but the results reproduce the qualitative outputs of the experiments. The mean streamwise velocity is modified in the buffer layer; the peak of the streamwise turbulent intensity, in wall units, increases and its maximum moves far from the wall; and the vertical turbulent intensity is largely reduced in the wall region. An interesting outcome from both the simulation and the experiments is that the strength of the longitudinal vortices is reduced when the polymers are present.     

二元合金微观偏析的相场法数值模拟

使用耦合溶质场的相场模拟研究了Ni-Cu二元合金枝晶生长过程中固相溶质扩散系数D_s 对枝晶形貌和微观偏析等的影响.计算结果表明，随着D_s的减少，固液界 面前沿溶质扩散层越薄，枝晶生长越有利，枝晶尖端生长的速度越大，侧向分支越发达；D< sub>s越小，固相中溶质成分的波动越强烈，随着D_s的增大，固相中溶质 成分的波动相应减小；溶质微观偏析程度随D_s的增大而减小. 关键词： 相场方法 微观偏析 固相扩散系数 数值模拟     

多级轴流压气机全工况特性计算

本文使用三维粘性流动计算软件Fine／Numeca,对某十五级轴流压气机进行了内流流场和全工况特性的数值计算尝试。分析了该压气机在设计工况和非设计工况的性能,同时把整机计算结果和前七级叶片的计算结果进行了比较。计算结果表明,当计算的级数较少时,目前的软件和硬件平台可以比较合理地预测压气机的全工况特性;而当计算的级数较多时,准确的数值模拟仍需要更为准确的多级模型和数值方法。     

Meshless simulation of equilibrium swelling/deswelling of pH‐sensitive hydrogels

Hydrogels have been widely used in microelectromechanical systems (MEMS) and Bio‐MEMS devices. In this article, the equilibrium swelling/deswelling of the pH‐stimulus cylindrical hydrogel in the microchannel is studied and simulated by the meshless method. The multi‐field coupling model, called multi‐effect‐coupling pH‐stimulus (MECpH) model, is presented and used to describe the chemical field, electric field, and the mechanical field involved in the problem. The partial differential equations (PDEs) describing these three fields are either nonlinear or coupled together. This multi‐field coupling and high nonlinear characteristics produce difficulties for the conventional numerical methods (e.g., the finite element method or the finite difference method), so an alternative—meshless method is developed to discretize the PDEs, and the efficient iteration technique is adopted to solve the nonlinear problem. The computational results for the swelling/deswelling diameter of the hydrogel under the different pH values are firstly compared with experimental results, and they have a good agreement. The influences of other parameters on the mechanical properties of the hydrogel are also investigated in detail. It is shown that the multi‐field coupling model and the developed meshless method are efficient, stable, and accurate for simulation of the properties of the stimuli‐sensitive hydrogel. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 326–337, 2006     

湍流燃烧二阶矩模型的大涡模拟验证

对美国Sandia国家实验室测量的甲烷-空气湍流射流火焰进行了三维大涡模拟(LES),其统计的时均量以及脉动量符合实验测量值,且和RANS代数二阶矩湍流燃烧模型模拟结果大致符合。LES统计得到的化学反应率系数脉动和甲烷浓度脉动的互关联与对应的时均量梯度的乘积分布趋势相同,大小幅值的位置也相对应,与二阶矩湍流燃烧模型的封闭假设相符,验证了二阶矩代数燃烧模型的合理性。     

基于界面跟踪方法的汽蚀模型和算法的有效性验证

针对两相附着汽蚀流动机理,基于界面跟踪方法发展了新的汽蚀模型和算法。所发展的汽蚀模型和算法不仅考虑了液相／气相界面处的压力差,而且考虑了耦合Reynolds-Averaged Navier-Stokes方程求解技术得到的流场压力梯度信息来迭代计算附着汽蚀形状。采用具有试验数据的半球形头部圆柱体汽蚀绕流作为算例来验证所提出的汽蚀模型和算法的有效性。采用不同的网格数和松弛因子数值验证了发展的汽蚀模型和算法的有效性。三种汽蚀数下的数值计算结果得到的压力系数分布与试验数据完全吻合。结果表明所提出的汽蚀模型和算法能够准确模拟出汽蚀发生点和汽蚀长度。