Kinetics of thermoset cure and polymerization in the glass transition region

A theoretical approach to thermoset cure kinetics based on Arrhenius kinetics and mobility was developed by considering the activation of the reacting group and chain mobility as elementary steps for reaction. This extended kinetic equation was successfully applied to the curing of an epoxy by an amine, the trimerization of a cyanate, and to the polymerization of methyl methacrylate. Full agreement between theory and experimental data was obtained in all cases. The activation energies for chain mobility were exceptionally low (0.3–1 kJ/mol for bisphenol-A-based epoxy and cyanate) which indicates that the structural units must undergo only small-angle rotational oscillations to allow a reaction. A theoretical time–temperature–transformation (TTT) diagram is also presented. © 1993 John Wiley & Sons, Inc.     

Thermal analysis of vinyl siding

Vinyl siding is typically produced by co-extruding a capstock (surface layer) over a PVC substrate formulation. The capstock is often non-PVC, these systems can result in warpage during or after production. In our study we will show that this warpage can result from an interfacial induced stress related to the mismatch between the glass transition of the substrate and the capstock. Additionally, both TMA and TMDSC were used to probe the stress release. Capstock formulations which better match the glass transition of the PVC substrate result in superior performance.     

Calorimetric study ofβ-cyclodextrin undecahydrate

Heat capacities of crystalline-cyclodextrin undecahydrate have been measured in the temperature range between 13 and 300K by use of a miniaturized adiabatic low-temperature calorimeter. A first-order phase transition occurred at 226K with a discontinuous entropy change of 45.0 ± 1.0J K ^–1 mol^–1. The highly disordered nature of the high temperature phase was considered in relation to the entropy contribution. A glass transition phenomenon observed around 150K was ascribed to the freezing of a configurational change of the protons engaged in the four-membered hydrogen-bonded ring which appeared only in the low temperature phase.     

Thermal Oxidative Stability of Heat-Stabilised Polyamide 66 by Differential Scanning Calorimetry

The thermal stability of heat-stabilised polyamide 66 in an oxidative environment is evaluated by DSC. The oxidative stability of the polyamide decreases as a result of repeated injection moulding. The results also indicate that the presence of glass fibres in the polyamide has a negative influence on the oxidative stability. Both isothermal and dynamic DSC measurements seem to be useful tools for assessing the stability of polyamides and there is a relationship between data determined using both procedures. This revised version was published online in July 2006 with corrections to the Cover Date.     

Acceleration of the cationic polymerization of an epoxy with hexanediol

Thin films of 3,4-epoxycyclohexylmethyl 3',4'-epoxycyclohexane carboxylate were UV irradiated (1.1 J cm^-2) under isothermal conditions ranging from 0 to 50°C. Under these conditions the polymerization advanced quickly but only to a conversion level of less than 10% before the reaction rate slowed by more than an order of magnitude. This drop off in rate was not caused by the glass transition temperature, T _g, reaching or exceeding the reaction temperature, T _rxn, since the epoxide's T _g remained at least 40°C below T _rxn. Raising the sample temperature above 60°C caused a sharp increase in the conversion level. At 100°C conversion exceeds 80% and the ultimate T _g approaches 190°C. The addition of 10 mass% 1,6-hexanediol, HD, to the epoxy caused the conversion at room temperature to quintuple over the level obtained without the alcohol present. The heat liberated from this alcohol epoxy blend during cure on a UV conveyor belt system caused the sample's temperature to increase by about 100°C above ambient whereas the epoxy alone under these conditions only experienced a modest temperature rise of about 26°C. If the amount of HD in the blend is increased above 10% the heat of reaction at 23°C decreases due to HD being trapped in a nonreactive crystalline phase. Boosting reaction temperatures above 50°C melts the HD crystals and yields significantly improved conversion ratios. As the level of alcohol blended with the epoxy is raised its ultimate T _g is lowered and when the concentration of alcohol in the blend nears 30 mass%T _g drops below room temperature. This revised version was published online in July 2006 with corrections to the Cover Date.     

Optimum gas chromatographic conditions in wall-coated capillary columns. Extended and simplified forms of the Golay-equation

Band broadening in capillary columns is satisfactorily described by the Golay-equation extended to situations of appreciable pressure drop by Giddings. In practice, however, several simplifications are often made. The effect of these simplifications on the calculated values of the minimum plate height and optimum carrier gas velocity are treated systematically.     

分析裂化气中0.5ppm～1%含量的杂质烃

本文介绍了一种分析裂化气中杂质烃的方法。所建分析系统由填充玻璃毛细管柱和填充预柱各一根、阀和FID各一个组成。采用一次进样、外标法定量,约30分钟即可完成测定裂化气中低至0.5ppm含量的痕量C_2～C_4炔和二烯。方法适用围范至少是0.5ppm～1%。当样品含量为1～5 ppm时,相对标准偏差小于50%。     

用两种方法合成长余辉发光玻璃的对比研究

在还原性气氛下高温固相反应法（一步法）合成了长余辉发光玻璃GA；用SrAl2O4:Eu,Dy荧光粉（SAED）与玻璃粉混合高温熔融（二步法）合成了长余辉发光玻璃GB和GC，通过XRD，发光光谱和磷光衰减曲线对样品进行了表征，荧光粉SAED和玻璃GA，GB，GC的发射峰值依次是525，493。462，516nm，发光强度和余辉时间都是SAED＞GC＞GB＞GA，玻璃的发射光谱峰随玻璃组成不同发生位移，两种发生合成的夜光玻璃发光性质存在明显的差异，同一合成方法下，玻璃基料决定着玻璃网络结构，同时也影响着夜光玻璃的发光性质。