Research on Raman-scattering and Fabrication of Multilayer Thin Film with Different Structures and Components Based on Pt/Ti/Si3N4/SiO2/Si Substrate

选用三水醋酸铅、乙酰基丙酮酸锆、四异丙氧基钛、乙酰丙酮作初始材料,用同样的方法分别制备了锆钛酸铅(PZT)和钛酸铅(PT)两种固体前驱物. 采用改良型的溶胶-凝胶工艺技术,分别在不同的Pt-Ti-Si₃N₄-SiO₂-Si基底上,按照不同的组合方式,制备了三种多层薄膜：PZT、PT/PZT-PZT/PT、PT/PZT/-/PZT/PT. 较详细地讨论了薄膜制备的工艺技术,发现当凝胶通过烧结和干燥后变成固态物质时,薄膜内部存在着较大的残余应力,当薄膜在600 ºC下退火时其内部残余应力可以被减小. 通过拉曼     

Fibrinogen adsorption onto 316L stainless steel, Nitinol and titanium

Fibrinogen adsorption onto mechanically polished biomedical grade 316L stainless steel (316LSS), nickel titanium alloy (Nitinol) and commercially pure titanium (CpTi) surfaces were studied by measurements of adsorption isotherms and adsorption kinetics using an ex-situ wavelength dispersive spectroscopy technique (WDS). Surface composition, roughness and wettability of these materials were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and water contact angle (WCA) measurements. Adsorption isotherm results showed that surface protein concentration on these materials increased with increasing concentration of fibrinogen in phosphate buffer solution. The fibrinogen adsorption isotherms were modeled by both the monolayer Langmuir isotherm and the multilayer Brunauer-Emmett-Teller (BET) isotherm. The results strongly suggest that fibrinogen forms multilayer structures on these materials when the concentration in solution is high. Complementary measurements on the absorbed fibrinogen films by spectroscopic ellipsometry (SE) support this view.     

Biodegradation of three-layer laminate films based on gelatin under indoor soil conditions

Three-layer gelatin films, composed of sodium montmorillonite (MMt) - plasticized gelatin (Ge-5MMt) (inner layer) and dialdehyde starch (DAS) - cross-linked and plasticized gelatin films (Ge-10DAS) (outer layers), obtained by heat-compression molding, were submitted to degradation under indoor soil burial conditions for 14 days. Biodegradation of multilayer film as well as individual components and control gelatin films was evaluated by monitoring water absorption and weight loss. It was established that technological treatments performed on gelatin, such as cross-linking, compounding with clay and heat-compression molding have a major impact on the biodegradation rate and extent. The possible reasons are discussed. Weight loss results revealed that the susceptibility to microbial attack during soil burial varied in the order: Ge-10DAS < multilayer < Ge-5MMt < gelatin control film. The intermediate behaviour of the multilayer was associated with the presence of hydrogen-bonding interactions between layers, induced by processing. Scanning electron microscopy revealed that the multilayer was preferentially biodegraded by filamentous microorganisms and even larvae in the later stages of the process. The presence of holes and pits on the multilayer surface was more likely attributed to the preferential removal of glycerol and DAS as shown by thermogravimetric analysis.     

Possibilities and limitations of synchrotron X-ray powder diffraction with double crystal and double multilayer monochromators for microscopic speciation studies

The performance of a combined microbeam X-ray fluorescence/X-ray powder diffraction (XRF/XRPD) measurement station at Hamburger Synchrotronstrahlungslabor (HASYLAB) Beamline L is discussed in comparison to that at European Synchrotron Radiation Facility (ESRF) ID18F/ID22. The angular resolution in the X-ray diffractograms is documented when different combinations of X-ray source, optics and X-ray diffraction detectors are employed. Typical angular resolution values in the range 0.3–0.5° are obtained at the bending magnet source when a ‘pink’ beam form of excitation is employed. A similar setup at European Synchrotron Radiation Facility beamlines ID18F and ID22 allows to reach angular resolution values of 0.1–0.15°. In order to document the possibilities and limitations for speciation of metals in environmental materials by means of Hamburger Synchrotronstrahlungslabor Beamline L X-ray fluorescence/X-ray powder diffraction setup, two case studies are discussed, one involved in the identification of the crystal phases in which heavy metals such as chromium, iron, barium and lead are present in polluted soils of an industrial site (Val Basento, Italy) and another involved in the speciation of uranium in depleted uranium particles (Ceja Mountains, Kosovo). In the former case, the angular resolution is sufficient to allow identification of most crystalline phases present while in the latter case, it is necessary to dispose of an angular resolution of ca. 0.2° to distinguish between different forms of oxidized uranium.     

Fabrication of self-assembled ultrathin photochromic films containing mixed-addenda polyoxometalates H5[PMo10V2O40] and 1,10-decanediamine

A layered phosphovanadomolybdate/1,10-decanediamine (1,10-DAD) self-assembled ultrathin film was fabricated by means of alternating adsorption of mixed-addenda polyoxometalates (POMs) (phosphovanadomolybdate, H₅[PMo₁₀V₂O₄₀]) and 1,10-DAD, and its photochromic properties were investigated. It is found that the self-assembled multilayer (SAM) film shows high-photochromic response, excellent photochromic stability and reversibility. The photochromic behavior of the SAM is closely related to the reduction potentials of addenda atoms in mixed-addenda POMs. In the case of photo-reduced mixed-addenda POMs, the electron is localized on the more reducible atom, and the addenda atoms with higher reduction potentials show prior photochromism compared with those with lower reduction potentials. The coloration speed is improved after introduction of V into molybdenum POM. The well-ordered lamellar structure of the film was well maintained during the coloration.     

Synthesis of Nitrogen Incorporated Carbon Nanotubes with Different Diameters by Catalytic Pyrolysis of Butylamine

Bamboo-like nitrogen-doped carbon(CNx) nanotubes were synthesized by chemical vapor deposition (CVD) at a high reaction temperature of 600―900 °C. The butylamine and Fe/SBA-15 molecular sieve have been used as precursor and catalyst, respectively. Transmission electron microscopy(TEM) and high resolution transmission electron microscopy(HRTEM) observations show that the outer diameter and wall thickness as well as the inner diameter were increased with increasing reaction temperature in a temperature range of 600―800 °C. A synergism mechanism of the growth through bulk diffusion and the competitive growth through surface diffusion functions during the synthesis of CNx nanotubes was proposed.     

基于叶绿素荧光光谱分析的稻瘟病害预测模型

为了实现稻瘟病的快速、准确和无损检测,力求构建稻瘟病害预测模型。根据水稻叶片相对病害面积将稻瘟病划分为3个等级,通过激光诱导法采集不同病害等级的活体水稻叶片叶绿素荧光光谱。选取502～830 nm波段激光诱导叶绿素荧光光谱(LICF)作为研究对象,利用Savitzky-Golay平滑法(SG)和一阶导数变换(FDT)对光谱信息进行预处理,通过主成分分析(PCA)方法获取经SG-FDT预处理后光谱的特征向量,根据累积贡献率和方差选取前3个主成分进行分析。将试验样本分为建模样本和检验样本,以稻瘟病害等级为预测指标,利用建模样本的133片叶片的光谱和病害信息分别结合判别分析(DA)、多类逻辑回归分析(MLRA)和多层感知器(MLP)建立稻瘟病的预测模型,利用检验样本的89片叶片的光谱和病害信息对所建模型进行预测检验,完成对PCA-DA、PCA-MLRA和PCA-MLP的对比寻优。结果表明,PCA-DA,PCA-MLRA和PCA-MLP模型均能完成对稻瘟病害的预测,但PCA-MLP模型的平均预测准确率能够达到91.7%,相比PCA-DA和PCA-MLRA模型,在稻瘟病害3个等级上均具有较好的分类和预测能力。     

Fabrication of polymer compound microlens by lens-on-lens microstructures

We proposed a novel method for fabricating polymer compound microlenses (PCMLs) using micro-inkjet technique and subsequent curing process. Two different types of PCMLs with sandwich microstructure (PDMS-Glycerol-PDMS), concave and convex PCMLs, have been designed and fabricated in experiments. Convex PCML has two real images and two foci. The concave PCML has one real and one virtual focal planes, which can generate one real image and one virtual image respectively. Moreover, the diameter of concave PCML can be controlled by adjusting the curing time and temperature. The proposed method is simple, efficient and suitable for realizing large-scale high numerical aperture PCMLs array, which has potential applications in diverse optical systems such as optical storage and three-dimensional imaging.     

氧化石墨烯/聚电解质层层自组装制备单价离子选择性膜

采用层层自组装法在改性聚丙烯腈(PAN)膜表面交替沉积聚乙烯亚胺(PEI)和聚丙烯酸-氧化石墨烯(PAA-GO)混合液,制得了单价离子选择性复合膜。X射线衍射(XRD)测试结果表明成功合成了氧化石墨烯(GO)并在复合膜中均匀分散。扫描电镜(SEM)观察结果证实了多层聚电解质PEI/PAA-GO成功地组装在基膜上,并用紫外-可见(UV-Vis)光谱进一步证实了组装过程的均匀性和连续性。接触角和性能测试表明加入GO后,复合膜的亲水性和单价阳离子的选择性明显增大。这种高通量、高选择性的防污复合膜在分离和水的软化方面有很好的应用前景。     

Fabrication of Covalently Linked PAH/PVS Layer-by-layer Assembled Multilayers via a Post-photochemical Cross-linking Strategy

A post-photochemical cross-linking strategy was successfully demonstrated to enhance the stability of polyelectrolyte poly(allylamine hydrochloride)(PAH)/poly(vinylsulfonic acid sodium salt)(PVS) multilayers. Conventional polyelectrolyte multilayers of PAH/PVS are usually fabricated through electrostatic layer-by-layer(LbL) assembly, resulting in poor stability, especially in basic solutions, which leads to the urgent demand for converting weak electrostatic interactions into covalent bonds to enhance the stability of the multilayers. This stability problem has been ultimately addressed by post-infiltrating a photosensitive cross-linking agent, 4,4'-diazostilbene-2,2'- disulfonic acid disodium salt(DAS), into the LbL assembled films to initiate the photochemical reaction to cross-link the multilayers. The obviously improved stability of the photo-cross-linked multilayers was demonstrated through experiments with basic solution treatments. Compared to the complete decomposition of uncross-linked multilayers in basic solution, over 74.4% of the covalently cross-linked multilayers were retained under the same conditions, even after a longer duration of basic solution treatment.