Direct analysis of fly ash materials by inductively coupled plasma atomic emission spectrometry using slurry nebulization

Fly ash samples of cement works were analysed using slurry nebulization inductively coupled plasma atomic emission spectrometric (ICP-AES). Because of the influence of the experimental factors on the signal intensity, the optimal conditions of the analysis circumstances were determined. Control analyses (wet digestion followed by ICP-AES, and XRF of dry powders (pressed pellets)) were also carried out to compare the results. Based on the result, it was concluded that the slurry nebulization method using slurry standard of same type reference material for calibration can be applied for rapid but less precise (RSD 5–10%) determination of the elements in fly ash.     

火花激发原子发射光谱分析不锈钢线材

火花激发原子发射光谱法应用于直径小于8mm的不锈钢线材的分析，对此类试样应用了一种特制的夹具，用块状标准样品制作工作曲线。由于线状试样和块状标准样品之间的形状差异所产生的系统不确定度借采用同类型标样作校正，对共存元素的相互干扰也采用了相应的校正方法。其它分析条件，包括严格的制样工序，氩气的纯度要求及其流量控制，以及光源的最佳条件等，作了深入的试验。按所提出的方法测定了不锈钢线材试样中碳、硅、锰、磷、硫、铬、镍及钛等8个元素。经校正后的结果与化学法测得结果相符。     

毛细管电泳-电感耦合等离子体原子发射光谱法对田七提取液中Fe、Cu和Mg存在状态的研究

提出了以水作溶剂微波萃取提取,并以毛细管电泳电感耦合等离子体原子发射光谱(CE-ICP-AES)法测定田七提取液中Mg、Cu和Fe的形态的分析方法。实验结果表明:Mg仅以游离态存在;而Cu和Fe除了游离态以外,还存在其它三种未知的形态。此外,还测定了田七中20个微量元素的总含量,并得到了上述待测元素在水提取液中的提取率。     

2，4，6－三苯基氧鎓盐分子内旋转受阻对其发光行为的影响

研究了４－位苯基取代基旋转受阻和旋转自由的２，４，６－三苯基氧盐的光物理性质。实验结果表明，当４－位苯基取代基旋转受阻时，氧盐化合物在激发态时引起的分子内极化程度比４－位取代基旋转自由的氧盐化合物大，即在激发态时旋转受阻氧盐化合物发生的分子内电荷转移能力较强；４－位取代基旋转自由的化合物的荧光量子产率随溶剂粘度的增大而有所增大，但旋转受阻化合物在相同的条件下则出现相反的结果。实验结果还表明，４－位取代苯基旋转受阻对化合物的荧光发射不利。     

La2O3,Y2O3-Mo次级发射材料研究

采用粉末冶金方法制备了La2O3，Y2O3-Mo次级发射材料，测试了各种材料的次级发射系数。结果表明在钼中加入稀土氧化物可以具有很好的次级发射性能。经过激活处理后，材料的最大次级发射系数均高于2．0，达到了材料使用要求的发射水平。应用扫描电镜(SEM)和光电能谱仪(XPS)研究了稀土元素在烧结体断口和发射前后在试样表面的分布情况。分析结果表明稀土元素易于在晶界处偏聚，且发射后试样表面稀土元素的相对浓度明显高于发射前的浓度。     

辉光放电原子发射光谱法快速分析生铸铁

通过对辉光光源参数-放电电流、放电电压、预溅射时间和分析时间对生铸铁标样放电强度和稳定性影响的研究,优化光源参数,建立了辉光放电原子发射光谱法同时测定生铸铁中碳、硅、锰、磷、硫等12个元素的快速分析方法。分析生铸铁试样时发现了不同灰口铸铁在碳分析结果方面存在偏差,对碳的偏差进行了讨论并通过制样条件和光源参数的调整可以有效地减小偏差。通过对不同生铸铁样品进行准确度和精密度试验,结果表明:分析结果与标准值或化学法结果一致。分析一件试样的时间仅需2~5 min。     

Optical emission spectroscopy as a real time diagnostic tool for plasma-assisted deposition of TiN

Real-time optical emission spectroscopy (OES) was used to monitor the deposition of TiN both from mixtures of tetrakis(dimethylamino)titanium (TDMATi)-N₂ and TiCl₄-H₂-N₂ in an electron cyclotron resonance chemical vapor deposition system. The accurate control of the ratio of the emission intensities of ionized nitrogen at 391.4 nm and molecular nitrogen at 357.7 nm (N ₂ ⁺ /N₂) led to low temperature deposition of stoichiometric TiN (Ti/N ≈ 1) and very low resistivity in both cases. It was found that high ion density plasmas are crucial for a considerable reduction of the deposition temperature while maintaining good film quality. OES shows that the abundance of certain excited plasma species is not only dependent on the gas mixture and the deposition parameters, such as total pressure and microwave power, but also is strongly affected by the magnetic field configuration. The deposition rate and the film resistivity can be related to the emission intensity ratio, I(N ₂ ⁺ )/I(N₂). Finally, the two processes are compared in terms of the quality of as-deposited and heat-treated films. The comparison shows that the films obtained with TDMATi exhibit lower resistivity and are thermally more stable than with TiCl₄.     

Slurry nebulization ICP-AES spectrometry method for the determination of tin in organotin(IV) complexes

This paper proposes a quick, novel method for tin determination in organotin chemicals by slurry nebulization inductively coupled plasma atomic emission (ICP-AES) spectrometry. The method was tested by the measurement of five organotin carboxylate complexes of known composition for obtaining simple stoichiometric data. The slurries were prepared by first dissolving the organotins in an adequate solvent (methanol, pyridine or acetone) well miscible with water and then adding this solution drop-by-drop to a 0.005% TX-100 tenzide solution while maintaining intensive mixing. Dynamic laser light scattering experiments showed that the average equivalent particle size in the resulting slurry was ≈0.3 μm for all samples and solvents. Under suitable ICP-AES measuring conditions, the signal recoveries were found to be between 101.8 and 106.6%, which allowed direct nebulization and calibration against aqueous solutions. Typically, 70 μg l⁻¹ detection limit and 1–5% relative S.D. on five replicates can be achieved by the described method.     

Determination of boron in boron-alloyed steels by inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometry (ICP-AES) procedure has been developed and examined for the determination of boron content (0.01 up to about 2% B) in boron-alloyed steels such as POLDI ATA BOR (65% Fe, 19%Cr, 12% Ni, 1.5% Mn, 1% B), POLDI ATA BOR EXTRA (62% Fe, 18% Cr, 13% Ni, 2.5% Mo, 1.5% Mn, 1% B) and POLDI ATA BOR-R (75% Fe, 18% Cr, 3.5% Ti, 1.8% B). The steel sample is dissolved with a mixture of hydrochloric, nitric, sulfuric and phosphoric acids in a quartz vessel. Borides of alloyed metals, especially of iron and chromium, are quantitatively decomposed. The presence of phosphoric acid in a sample solution reduces the volatility of boric acid with water vapour.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

Enhanced deep-red emission in donor-acceptor molecular architecture: The role of ancillary acceptor of cyanophenyl

Cyanophenyl as ancillary acceptor to modify donor-acceptor compound,plays an effective role in shifting the emission color to deep red and maintaining the luminescent efficiency.