玻璃基质微流控芯片用于DNA片段的分离和C677T基因突变的快速检测

基于微加工方法,在一般实验条件下,成功地制备了玻璃芯片。利用水溶性聚合物对玻璃通道进行动态修饰,从而抑制了DNA分子的吸附作用,并成功地用于DNA片段的分离和四氢叶酸还原酶基因(MTHFR)中C677T的突变检测。     

聚对苯二甲酸乙二酯微流控芯片的制备和表面改性

高聚物微流控芯片具有制备简单、成本低、可批量生产等突出优点而有望成为一次性器件,近年来在国内外引起了同行们的兴趣.但是,高聚物表面的憎水性、对有机分子的强吸附性、电渗流的不稳定性等又成为高聚物芯片在微流控分析领域得以广泛应用的障碍.表面改性是改善高聚物芯片分析特性的有效途径.     

PREPARATION OF POLYSULFONAMIDE/TiO2 NANOCOMPOSITES BY SOL-GEL

Polysulfonamide (PSA) was synthesized at room temperature, the polymerization based on terephthaloyl chloride and 3,3 '-diaminodiphenylsulfone in the common solvent N,N -Dimethyl-acetamide (DMAc). Polysulfonamide/titanium oxide nanocomposites were prepared by sol-gel method. Tetrabutyl titanate(TBT) was added into the polysulfonamide solution, at the same time ,some water was mixed to make the TBT hydrolyze. In the process, hydrochloric acid was used to catalyze the reaction. The polysulfonamide chemistry structure was characterized by FT-IR spectrum. Atomic force microscopy (AFM) was employed to observe the microstructure of the composite film. The thermal property was investigated by TGA.The results show that we have succeeded to synthesize the polysulfonamide, TiO2particles were well distributed in the composite film and average size was about 20 nm on average, the heat-resistance of nanocomposite was batter than the pure polysulfonamide.     

Synthesis of Fullerene-end Functionalized Poly（methyl methacrylate） via Reverse Atom Transfer Radical Polymerization

The use of the reverse atom transfer radical polymerization （RATRP） to end-functionalize poly（methyl methacrylate） （PMMA） with fullerenes, e.g. C60 and C70 was described in this paper. The Cl-terrninated PMMA was prepared via RATRP with designed molecular weight and narrow molecular weight distributions, and then directly used to react with fullerenes to produce C60（C70） terminated PMMA polymers in the presence of CuBr/Cu/bipy or FeCl2/bipy catalysts. The resultant polymers exhibit good solubility in some common organic solvents, e.g. THF, CHCl3 and toluene, and were well structurally characterized by a variety of physical techniques.     

低热-高压法制备PLGA多孔支架及其体外降解研究

采用低热-高压法制备了聚(dl-丙交酯／乙交酯)75／25(PLGA75／25)组织工程多孔支架。该方法避免了使用有机溶剂，支架的孔隙率在90％以上，孔径大小分布均匀。多孔支架经过酒精处理后，支架表面产生许多微小的凹陷；用藻酸钙改性处理后，支架形态保持良好。两种处理都使支架的压缩强度有所增大，亲水性增强。虽然孔隙率高的支架降解速率稍慢，但其体外降解规律基本一致：特性粘数争力学强度衰减快，而质量损失较慢，降解6周后，支架的质量损失仅为3％左右；体外降解3周后，支架的形态保持良好，可望在细胞移植争组织修复的早期发挥支撑作用。     

柠檬酸铝/聚丙烯酰胺胶态分散凝胶反应动力学和机理的研究

采用粘度法研究了柠檬酸铝（AlCit)与部分水解取丙烯酰胺（HPAM）胶态分散凝胶体系的反应动力学。结果表明，胶态分散凝胶体系的交联反应是一级反应。并推导出胶态分散凝胶体系的反应动力学方程。     

羟基铝溶液及铝交联蒙脱土的研究

本文用(27)~Al NMR法和8-羟基喹啉萃取法分别研究了羟基铝溶液中十三聚铝含量的变化规律,还用X-射线衍射法研究了铝交联蒙脱土d_(001)的变化。研究结果表明,铝离子的聚合情况主要由羟铝比决定,而浓度影响不大。随着羟铝比的增加,溶液中单核铝离子含量减少,十三聚铝离子相对含量增加,所得铝交联蒙脱土的d_(001)也随之增大。参照这些变化规律、控制羟基铝溶液的组成,可以制备各种层柱状铝交联蒙脱土复合物。     

PEG作为成孔剂对聚(N-异丙基丙烯酰胺-co-丙烯酸)水凝胶性能的影响

以PEG400,1000,6000为成孔剂,合成了一系列聚(N-异丙基丙烯酰胺co丙烯酸)水凝胶,研究了成孔剂分子量和数量对凝胶性能的影响.结果表明,聚乙二醇(PEG)分子充当成孔剂,不参与反应.PEG分子量越大,投料越多,所得凝胶孔的孔径越大,孔数目越多,在室温时可以容纳更多的水分子,因而溶胀率也越大.凝胶的大孔结构有利于水分子的进出,所以响应速率比普通共聚凝胶快.随着PEG分子量增大,孔数目增多,响应速率相应变快.