The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanes

Poly(ε‐caprolactone)‐based segmented polyurethanes (PCLUs) were prepared from poly(ε‐caprolactone) diol, diisocyanates (DI), and 1,4‐butanediol. The DIs used were 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluenediisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HDI). Differential scanning calorimetry, small‐angle X‐ray scattering, and dynamic mechanical analysis were employed to characterize the two‐phase structures of all PCLUs. It was found that HDI‐ and MDI‐based PCLUs had higher degree of microphase separation than did IPDI‐ and TDI‐based PCLUs, which was primarily due to the crystallization of HDI‐ and MDI‐based hard‐segments. As a result, the HDI‐based PCLU exhibited the highest recovery force up to 6 MPa and slowest stress relaxation with increasing temperature. Besides, it was found that the partial damage in hard‐segment domains during the sample deformation was responsible for the incomplete shape‐recovery of PCLUs after the first deformation, but the damage did not develop during the subsequent deformation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 557–570, 2007     

在重力场和磁场影响下自旋刚性航天器的周期运动

考虑重力场和磁场对轴对称航天器本体的影响，研究其质心在圆形轨道上的运动,通过降低系统的运动方程数，并将它变成为一个带电粒子在电磁场作用下的平面运动．确认系统运动是稳定的，并通过Liapunov全纯积分定理，构建其近似的周期运动.     

Matrix Lax Polynomials, Geometry of Prym Varieties and Systems of Hess–Appel’rot Type

We consider a four-dimensional generalization of Hess–Appel’rot system and costruct its Lax pair. Both classical and algebro-geometric integration procedure are proceeded. The algebro-geometric integration is based on deep facts from geometry of Prym varieties such as the Mumford relation and Mumford-Dalalyan theory. The integration is similar to the integration of Lagrange bitop which has recetly been performed by the authors.     

Wellposedness for the Navier–Stokes flow in the exterior of a rotating obstacle

In this paper we study the Navier–Stokes boundary‐initial value problem in the exterior of a rotating obstacle, in two and three spatial dimensions. We prove the local in time existence and uniqueness of strong solutions. Moreover, we show that the solutions are global in time, in two spatial dimensions. Copyright © 2005 John Wiley & Sons, Ltd.     

非均匀多孔介质有效热导率分析

本文采用控制容积法,界面调和平均导热系数值以及图形处理方法对典型非均匀多孔介质硬质聚氨酯泡沫材料的导热过程进行了分析与模拟计算。结果表明:多孔介质的内部结构是影响温度分布和热量传递的主要的因素,其影响程度与骨架和孔隙的导热系数,孔隙的大小和分布有关;计算得到的有效热导率值与文献中实验测量结果吻合较好。本文的研究结果可以推广到更为复杂的非均匀多孔介质的场合,从而可以进一步认识非均匀多孔介质中的导热规律,为工程计算提供更精确的计算方法。     

一种新型的侧链型聚氨酯高分子钌聚合物的合成

通过分子设计,将带有-OH端基的钌(Ⅱ)联吡啶配合物[Ru(bpy)2L]PF6{L=希夫碱4-[(N甲-基-N羟-乙基)氨基]苯甲醛缩肼基硫代甲酸甲酯}与甲苯-2,4异-氰酸酯、丙烯酸羟乙酯发生共聚合反应,合成了新的侧链型聚氨酯高分子钌聚合物(4)。4的结构经红外光谱和差热分析表征。     

泡沫铅对VRLA电池负极活性物质结构及性能影响

0引言随着36V/42V汽车电源系统的提出,新一轮汽车用电池的竞争不断加剧。从目前情况看,铅酸电池由于具有成本低廉,使用可靠,原材料来源丰富,铅回收率可高达98%等优点,因此成为电动车电源最实际的选择之一[1]。但作为电动车用电池,需要克服其比能量低、充电接受能力差和负极硫酸盐化等缺点。为此各国科学家开展了大量的研究工作。最近报道用铸造多孔体作为敞口铅酸电池的集流体,它的比表面积为14cm2·cm-3,正极活性物质利用率上升到50%,远高于传统的铸造板栅[2]。在铅酸电池集流体研究领域里另一个重大进步,就是以R V C(R etic-ulated V i…     

Kinetics of formation of a linear polymer-polymer network system in the presence of 3d metal chelates

For semi-interpenetrating polymer networks (semi-IPNs) based on an incompatible polyurethane network/linear polymethylmethacrylate pair formed in situ in the presence of 3d metal chelates, we have studied the effect of the system composition on the kinetics of formation of the components and the nature of complex formation between the metal compound and the polymer matrix. The ratio of the system components has been shown to have an effect on the selection of the macroligand in formation of complexes of the metal chelate with the polar groups of the semi-IPN, where the general character of the kinetic behavior for the formation of the network and the linear polymer is preserved. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 42, No. 6, pp. 351–356, November–December, 2006.     

表面膨胀粘度的测定研究

用不同浓度的NaCl和表面活性剂直链的十二烷基苯磺酸钠(LAS)、稳定剂聚丙烯酰胺和水所组成的泡沫体系为研究对象,通过表面压松弛的方法,利用计算机数据拟合,得到了计算表面膨胀粘度的方法。     

弹性体型聚氨酯和聚碳酸酯共混物的形态结构

用ＤＳＣ、ＷＡＸＤ和ＳＡＸＳ研究了溶液共混的弹性体型聚氨酯（ＰＵ）／聚碳酸酯（ＰＣ）共混物的结构。结果表明，ＰＵ／ＰＣ为部分相容体系；共混过程中，溶剂ＤＭＦ的诱导作用使ＰＣ形成结晶，其长周期与ＰＵ硬段形成微相的长周期相近