Influence of metal electrodes on c‐axis orientation of AlN thin films deposited by DC magnetron sputtering

Nanocrystalline aluminum nitride (AlN) thin films were deposited on two types of metallic seed layers on silicon substrates, (111) textured Pt and (110) Mo, by reactive DC magnetron sputtering at low temperature (200 °C). Both textured films of Pt and Mo promote nucleation, thereby improving the crystallinity and epitaxial growth condition for AlN thin films. The deposited films were examined by X‐ray diffraction, scanning electron microscopy and atomic force microscopy techniques. The results indicated that the preferred orientation of crystallites greatly depends upon the kinetic energy of the sputtered species (target power) and seed layers used. Furthermore, AlN thin films with c‐axis perpendicular to the substrate grew on both types of metal electrodes at all power levels larger than 100 W. By comparing the structural properties and compressive stresses at perfect c‐axis orientation conditions, it is evident that AlN films deposited on (110) oriented Mo substrates exhibited superior properties as compared with Pt/Ti seed layers. Furthermore, less values of compressive stresses (?3 GPa) as compared with Pt/Ti substrates (?7.08 GPa) make Mo preferentially better candidate to be employed in the field of suspended Micro/Nano ‐ electromechanical systems (MEMS/NEMS) for piezoelectric devices. Copyright © 2017 John Wiley & Sons, Ltd.     

Elastoplastic Axisymmetric Stress-Strain State of Laminated Shells Made of Isotropic and Transversely Isotropic Materials with Different Moduli

A method is developed for analysis of the elastoplastic stress-strain state of laminated shells of revolution under axisymmetric loading. The shells are made of isotropic and transversally isotropic materials with different moduli. The method is based on the Kirchhoff-Love hypotheses for the whole laminate, the theory of deformation along paths of small curvature (for isotropic materials), and the theory of elasticity with different tensile and compressive moduli (transversely isotropic materials). The problem is solved by the method of successive approximations. Numerical examples are given __________ Translated from Prikladnaya Mekhanika, Vol. 41, No. 8, pp. 88–96, August 2005.     

γ－Fe_2SiO_4在静水压下的压缩行为的测定

采用同步辐射高压原位Ｘ光衍射技术及金刚石对顶压砧高压装置，对γ－Ｆｅ＿２ＳｉＯ＿４进行了静水压条件下等温压缩行为的测定，最高压力达２３ＧＰａ。γ－Ｆｅ＿２ｓｉＯ＿４在０～２３ＧＰａ压力范围内的ｐ、Ｖ数据表明，其等温压缩可分为两个阶段：若设Ｋ＇＿０＝４，在０～１８Ｇｐａ，Ｋ＿０＝１８９±２ＧＰａ；而在１８～２３０Ｐａ，Ｋ＿０＝２１３±２ＧＰａ。我们认为，样品在１８ＧＰａ以下处于较好的静水压状态，压力超过１８ＧＰａ，传压介质的静水压性质变坏，所以Ｋ＿０值偏高。在整个实验过程中并未发现样品有任何发生相变的迹象。最后，对一些虽然使用了液体介质但得不到静水压条件的实验现象进行了讨论。     

柯尔莫哥洛夫检验在混凝土强度检测中的应用

回弹法是检测混凝土强度的一种常用方法,回弹法的测量精度依赖于数据本身的真实性。本文提出了一种利用柯尔莫哥洛夫检验控制测量数据误差的方法。     

复合材料层合板的低速冲击损伤及其剩余压缩强度研究

本文采用理论和实验方法研究了复合材料层合板的低速冲地及其剩余压缩强度。文中利用有限元方法和能量转换原理计算了层合板受到低速冲击的受载最危险状态，以及此时的应力分布；并用Ｔｓａｉ－Ｗｕ张量准则判断损伤情况，对产生损伤的单元进行相应的刚度折减，且作重复计算直至不产生新的损伤为止；最后，对受冲击的层合板还进行剩余压缩强度计算。在实验中，采用激光全息无损检测法测量了层合板的冲击损伤，并对受冲击的层合板进行     

Infrared thermographic evaluation of large composite grid parts subjected to axial loading

Many composite parts, such as laminated panels and grid-like shells, operate under high mechanical loading. Evaluation of their structural integrity is crucial to ensure the long-lasting operation of critical components. Since testing a structure under full or “proof” load might be dangerous for personnel, it would be preferable to use a remote, rapid inspection technique. This paper describes a practical application of IR thermography to the inspection of large composite parts used in the aerospace industry. This work has used just one cycle of increasing load from zero load to failure, and this was done for both for tensile and compressive loads. It is shown that, during the formation of micro-defects in polymeric composites, about 40 % of the total dissipated energy is expended for material heating, while about 60 % is related to material damage accompanied by an increase in the defect concentration. Non-uniform composite deformation causes temperature anomalies, whose amplitude may reach 1.5–2.5 °C at a load of about 50–60 % of the limit load.     

TNT炸药动静态变温三轴压缩力学性能的试验研究

介绍了一种高能材料动静态变温三轴压缩试验装置，在熔点以下温度，通过对国产单质炸药ＴＮＴ在中等应变速率（２－４／ｓ）及准静态（３×１０－３／ｓ）条件下三轴压缩力学性能的测试，得出ＴＮＴ的杨氏模量Ｅ、泊松比ν和屈服极限Ｙ，以及当加载速率和温度改变时这些参数的变化规律。并提出三轴应力状态下屈服极限的一种确定方法。该三轴压缩试验装置以及三轴压缩应力状态下力学参数的测试、分析、处理系统为研究高能材料力学性能提供了一套完整的技术和手段。     

软土地区人工冻土无侧限瞬时抗压强度的试验研究

冻结法施工在上海隧道建设中(如隧道旁通道、地下泵房等的设计与施工)得到广泛应用,也曾引发过严重的地质灾害(如上海地铁4号线外滩段的地质灾害)。因此安全、经济、合理地将冻结法用于上海软土地区隧道建设中已经成为上海工程建设中的一个重要的研究课题。本文以上海复兴东路越江隧道旁通道冻结法施工中遇到的第⑥层粉质粘土及第⑦层粉细砂为研究对象,针对设计冻结壁重要强度参数无侧限瞬时抗压强度,进行了室内试验研究,揭示了两种土的冻结强度随温度的变化关系,同时研究了粉细砂的冻结强度随含水率的变化规律。     

使用压缩感知的遥感图像振荡畸变几何校正方法

卫星平台振动和反射镜震颤会引起遥感图像中的振荡畸变。这类畸变难以通过常用的几何校正方法消除。对此,提出了一种使用压缩感知的几何校正方法。该方法基于有理函数模型(RFM)进行几何校正。在校正过程中,利用初始的RFM计算出地面控制点(GCPs)在图像中的投影坐标与实际成像坐标之间的偏差(称为投影偏差),以地面控制点处的投影偏差作为采样值,使用压缩感知技术重构出所有像元处的投影偏差,并据此对RFM进行像方补偿;利用经过补偿的RFM进行遥感图像纠正。通过补偿,消除了振荡畸变引起的RFM模型误差,进而提高校正性能。利用实测数据验证了该方法的有效性,并通过仿真数据分析了地标点的数量与分布对该几何校正方法性能的影响。     

基于压缩感知的一维海面与二维舰船复合后向电磁散射快速算法研究

矩量法作为数值方法中积分方程方法的代表, 具有计算精度高、所用格林函数自动满足辐射条件、无须额外设置边界条件等优点. 但是在舰船目标与海面复合后向电磁散射仿真中, 传统矩量法需针对每个入射角反复求解矩阵方程组, 导致其在处理后向散射问题时计算量大, 耗时长, 仿真效率低下. 为解决上述问题, 本文提出了一种基于压缩感知技术的矩量法的改进算法. 该算法在求解复合后向散射问题时, 首先利用观测矩阵与传统矩量法中的电压矩阵相乘, 得到一组新的低维度的电压矩阵; 其次通过求解新电压矩阵下的矩阵方程组, 获得电流矩阵的观测值; 最后利用恢复算法(本文采用正交匹配追踪算法)重构出所需的原始入射源照射下的电流系数. 通过与传统矩量法的计算结果对比, 表明本文所提算法能够在保证计算精度的前提下, 明显减少计算时间, 提高计算效率.