硫脲络合–火焰原子吸收光谱法测定低硅铝合金中的银含量

采用硫脲络合–火焰原子吸收光谱法测定低硅铝合金中的银元素含量。实验探讨了酸度及硫脲用量对银测定的影响及铝合金中基体元素与共存元素对银元素分析线的干扰情况。结果表明:选用9%的盐酸和3%的硝酸溶解试样最好,加入5 mL 50 g/L硫脲溶液可消除氯离子对试验结果的影响,基体铝元素和其它共存元素不干扰银的测定。根据低硅铝合金中银元素的含量范围,合成系列标准溶液,建立工作曲线,工作曲线的线性范围为0.05%~0.50%。银元素含量为0.30%的样品测定结果的相对标准偏差为0.15%(n=8),标准加入回收率为96.8%~98.5%。该方法操作简便、重现性好、测量结果准确可靠。     

悬浮固化-分散液液微萃取-液相色谱-串联质谱测定纺织废水中磷系阻燃剂

建立了悬浮固化-分散液液微萃取结合液相色谱-串联质谱测定纺织废水中5种痕量磷系阻燃剂的方法。通过对萃取过程中萃取剂、分散剂的种类与体积、盐浓度、溶液pH值等对萃取效率的影响因素优化,确立了最佳萃取条件。采用了密度小于水的十一烷醇（400 μL）为萃取剂,甲醇（300 μL）为分散剂,控制溶液pH值在6~9之间,NaCl添加量为2 g,萃取时间为涡旋2 min。在优化的萃取条件下,该方法在2~100 μg/L均有良好的线性关系,相关系数大于0.995,除二（2,3-二溴丙基）磷酸酯（BIS）的检出限为5 μg/L外,三（2-氯乙基）磷酸酯（TCEP）、三（1,3-二氯-异丙基）磷酸酯（TDCP）、三（1-氮丙啶基）氧化膦（TEPA）和三（2,3-二溴丙基）磷酸酯（TRIS）的检出限均为2 μg/L。后整理、染色和印花等实际废水样品加标试验表明,方法的平均回收率为71.6%~114.5%,RSD为2.7%~11.2%（n=6）。对11个样品进行检测,其中3个废水样品检出TCEP与TDCP化合物,含量为2.6~3.4 μg/L。本方法简单,快速,灵敏度好且环保绿色,能够对纺织废水中的5种痕量磷系阻燃剂进行准确的定性与定量检测。     

Effect of ethyl‐bridged diphenylphosphine oxide on flame retardancy and thermal properties of epoxy resin

Three commercialized flame retardants, 1,2‐bis(diphenylphosphinoyl)ethane (EDPO), 6,6‐(1,2‐phenethyl)bis‐6H‐dibenz[c,e][1,2]oxaphosphorin‐6,6‐dioxide (HTP‐6123), and hexa‐phenoxy‐cyclotriphosphazene (HPCTP), were used to prepare the flame retardant diglycidyl ether of bisphenol A (DGEBA) epoxy resin (EP) under the same experimental conditions. The effects of T_g, thermal stability, and water absorption properties of EP caused by the three flame retardants were investigated and compared, together with their flame retardant efficiency. Results showed that the introduction of the three flame retardants improved the flame retardant performance of EP but led to decreases in T_g and decomposition temperature. EDPO showed higher flame retardant efficiency than the other two flame retardants. EP/EDPO showed higher thermal stability, better flame retardant performance, higher T_g value, and lower water absorption than EP/HTP‐6123 and EP/HPCTP. The study discovered that EDPO and HTP‐6123 primarily act through the gas phase flame retardant mechanism, while HPCTP is primarily driven by the condensed phase mechanism.     

Effect of different ionic layered compounds decorated with zinc hydroxystannate on flame retardancy and smoke performance of epoxy resin

ZHS@ Mg‐Al‐LDH and ZHS@α‐ZrP hybrid materials were prepared by electrostatically loading zinc hydroxystannate (ZHS) on the layered compounds (Mg‐Al‐LDH and α‐ZrP) in this work. With the addition of 2 wt% of the two hybrid materials to epoxy resin (EP), respectively, the fire hazard of EP and its composites were investigated. The limiting oxygen index (LOI) of ZHS@ Mg‐Al‐LDH/EP composite increased by 19.0% compared with pure EP, while its peak heat release rate (PHRR), total heat release rate (THR), and peak smoke release rate (SPR) decreased by 48.2%, 20.8%, and 21.6%, respectively, evidenced by the results of the LOI test and cone calorimetry test (CCT). The LOI of ZHS@α‐ZrP/EP composite increased by 20.4%, and its PHRR, THR, and SPR decreased by 47.7%, 21.4%, and 27.1%, respectively. Both hybrid materials showed prominent flame retardant and smoke suppressing properties. In addition, through the analysis of the TG‐IR and Raman spectrum of residual char, the specific mechanism of flame retardance and smoke suppression was explored.     

A novel intumescent flame retardant imparts high flame retardancy to epoxy resin

Intumescent flame retardant (IFR) has received the considerable attention ascribed to the inherent advantages including non‐halogen, low toxicity, low smoke release and environmentally friendly. In this work, a novel charring agent poly (piperazine phenylaminophosphamide) named as PPTA was successfully synthesized and characterized by Fourier transform infrared spectra (FTIR) and X‐ray photoelectron spectroscopy (XPS). Then, a series of flame‐retardant EP samples were prepared by blending with ammonium polyphosphate (APP) and PPTA. Combustion tests include oxygen Index (LOI), vertical Burning Test (UL‐94) and cone calorimeter testing,these test results showed that PPTA greatly enhances the flame retardancy of EP/APP. According to detailed results, EP containing 10 wt% APP had a LOI value of 30.2%,but had no enhancement on UL‐94 rating. However, after both 7.5 wt% APP and 2.5 wt% PPTA were added, EP‐7 passed UL‐94 V‐0 rating with a LOI value of 33.0%. Moreover, the peak heat release rate (PHRR) and peak of smoke product rate (PSPR) of EP‐7 were greatly decreased. Meanwhile, the flame‐retardant mechanism of EP‐7 was investigated by scanning electron microscopy (SEM), thermogravimetric analysis/infrared spectrometry (TG‐IR) and X‐ray photoelectron spectroscopy (XPS). The corresponding results presented PPTA significantly increased the density of char layer, resulting in the good flame retardancy.     

Supramolecular self‐assembly modification of ammonium polyphosphate and its flame retardant application in polypropylene

In order to improve its water resistance and compatibility with polymer matrix, ammonium polyphosphate (APP) is modified with melamine‐trimesic acid (MEL‐TA) aggregates by supramolecular self‐assembly technology. Chemical structure and morphology of APP@MEL‐TA are investigated by Fourier transform infrared spectroscopy and scanning electron microscopy (SEM), respectively. Intumescent flame retardant system of APP@MEL‐TA and charring‐foaming agent is introduced into polypropylene (PP) matrix. The flammability and combustion behavior of PP composites are investigated by limiting oxygen index (LOI), UL‐94 vertical burning, and cone calorimetry tests. In terms of LOI values and cone combustion results, APP@MEL‐TA performs better than pristine APP. Char residue of PP composites is investigated by SEM and Raman spectra. Flame retardant mechanisms are proposed based on thermal decomposition, combustion results, and analysis on char residue.     

Flame retardancy and smoke suppression of silicone foams with microcapsulated aluminum hypophosphite and zinc borate

The flame‐retardant microcapsules were successfully fabricated with an aluminum hypophosphite (AHP) core. Fourier transform infrared (FTIR) and X‐ray photoelectron spectroscopy (XPS) were used to verify that AHP was encapsulated in the microcapsules, and thermogravimetry analysis showed that microencapsulated AHP (MAHP) possessed higher thermal stability than that of AHP. Then, a flame‐retardant and smoke suppression system for silicone foams (SiFs) was obtained through a synergistic effect of MAHP and zinc borate (2ZnO·3B₂O₃·3.5H₂O). The mechanical properties, flame retardance, and smoke suppression of SiFs with MAHP and zinc borate were tested using the tensile test, limiting oxygen index (LOI) test, UL‐94 test, and cone calorimeter test. The mechanical properties indicated that the tensile strength and elongation at break of SiFs could evidently improve with the incorporation of MAHP. Compared with pure SiF, SiF8 with 4.5‐wt% MAHP and 1.5‐wt% zinc borate could achieve an LOI value of 30.7 vol% and an UL‐94 V‐0 rating, the time to ignition amplified almost six times, the peak heat release rate and total heat release were 51.10% and 46.00% less than that of pure SiF, respectively, the fire performance index increased nearly 13 times, and the fire growth index value was only 13.18% of pure SiF. Moreover, the partial substitution of zinc borate imparted a substantial improvement in both flame retardancy and smoke suppression. Especially, the peak smoke production rate and total smoke production of SiF8 were merely 38.46% and 38.84% of pure SiF.     

Flame retardancy and thermal decomposition behavior of TPU/chitosan composites

The application of chitosan (CS) in new materials is a hot research topic. In this paper, CS was used alone as flame retardant to prepare thermoplastic polyurethane elastomer (TPU) composites. Then, the flame retardancy and thermal decomposition behavior of TPU/CS composites were intensively investigated using cone calorimeter test (CCT), scanning electron microscope (SEM), microscale combustion colorimeter (MCC) test, thermogravimetric analysis/infrared spectrometry (TG‐IR), and gas chromatography‐mass spectrometry (GC‐MS). The results showed that CS can reduce the fire risk of TPU; 2.0‐wt% CS could make the peak value of heat release rate (pHRR) decreased to 457.2 kW/m², reduced by 65.9% compared with TPU. And the peak value of smoke production rate (pSPR) and total smoke release (TSR) of the same sample was decreased by 79.4% and 54.2%, respectively. The TG‐IR and GC‐MS results confirmed that CS could promote TPU decomposition in advance, reacting with the decomposition products of TPU. Therefore, the production of combustible gas was reduced. The GC‐MS results showed that the production of isocyanates and ethers was reduced with the addition of CS. The digital photographs of SEM for the samples after CCT were shown that the char residue layer of the sample containing 2.0‐wt% CS was fibrous in shape. It could be speculated that the thermal decomposition products from TPU could react with CS at low temperature, which reduced the production of flammable gases. So CS had a good prospect in reducing the fire hazard for TPU.     

Design of aluminum trihydroxide and P‐N core‐shell structures and their synergistic effects on halogen‐free flame‐retardant polyethylene composites

In order to improve the performance of inorganic/organic composites, aluminum trihydroxide (ATH) core composites with a styrene‐ethylene‐butadiene‐styrene block copolymer grafted with maleic anhydride (MAH‐g‐SEBS) shell phase, and P‐N flame retardant as a synergistic agent, were prepared through an interface design. The effects of polyethylene glycol (PEG) content on the interfacial interaction, flame retardancy, thermal properties, and mechanical properties of high‐density polyethylene (HDPE)/ATH composites were investigated by small angle X‐ray diffraction, rotational rheometer, limiting oxygen index, thermogravimetric analysis (TGA), and tensile testing. The ATH synergistic effects of P‐N flame‐retardant improved the combustion performance of HDPE/ATH/PEG(3%)/MAH‐g‐SEBS/P‐N (abbreviated as HDPE/MH3/M‐g‐S/P‐N) composite by forming more carbon layer, increased the elongation at break from 21% to 558% compared to HDPE/ATH, and increased the interface thickness from 0.447 to 0.891 nm. SEM results support the compatibility of ATH with HDPE increased and the interfacial effect was enhanced. TGA showed the maximum decomposition temperature of the two stages and the yield of the residue at high temperature increased first and then decreased with the increase of PEG content. Rheological behavior showed the storage modulus, complex viscosity, and the relaxation time initially increased and then decreased with the increase of PEG content indicating PEG, M‐g‐S, and ATH powder gradually formed a partial coating, then a full coating, and finally an over‐coated core‐shell structured model.     

Organophosphate esters by GC–MS: An optimized method for aquatic risk assessment

Organophosphate esters used as flame retardants and plasticizers are ubiquitous contaminants in surface waters. Many studies indicate that these compounds are neurotoxicants, endocrine disruptors, and may affect reproduction and development of aquatic organisms. Thus, analytical methods that allow accurate quantification of these contaminants at environmentally relevant concentrations are desirable for risk assessment studies. In this study, a method based on solid phase extraction and gas chromatography coupled to mass spectrometry was developed for determination of organophosphate esters in river water extracts. Multivariate optimization was used to determine the best conditions for injection of larger volumes of sample in a Programmable Temperature Vaporization inlet. Furthermore, the matrix effect on the instrumental response was evaluated and compensated by association of extraction‐blank‐matched calibration and isotopically labeled focus standards. The method quantification limits ranged from 0.009 to 0.11 µg/L, staying below the predicted non‐effect concentration for the aquatic compartment for all analytes, which is a requisite for using in risk assessment studies. The method was applied to freshwater samples collected in rivers from the Sao Paulo State, Brazil, and eight out of the ten target organophosphate esters were quantified, being tris(2‐chloroisopropyl) phosphate and tris(phenyl) phosphate the most frequently detected compounds.