正交试验法优化CS汽化吸附条件

通过正交试验设计,优化了影响西埃斯(CS)标准样品管制备的参数:汽化温度、采样流速、采样时间。结果表明,CS标准样品管的最佳吸附条件为汽化吸附温度:260℃,采样N2流速:330mL/min,采样时间:15min。在15~1500ng范围内,色谱峰面积与进样量有良好的线性关系,线性相关系数为0.9995,检出限为6.0ng。     

利用偏钛酸浆料制备大比表面纳米管钛酸工艺的研究

以偏钛酸浆料为原料通过水热法合成了纳米管钛酸,并采用TEM,比表面积测定仪等分析手段观察其形貌和管径大小,测定了其比表面积和孔体积.同时运用正交实验法考察了反应温度、反应时间对纳米管钛酸比表面积和孔体积的影响.实验结果表明,所制备的纳米管钛酸平均比表面积高达 340m2 /g,最佳的制备工艺是:工业碱NaOH的质量分数为 25. 7 %、偏钛酸浆料的质量分数为 17. 1 %、后处理酸度为pH=1、反应温度为 120℃、反应时间为 20h.     

实验室废液的回收及效果评价——以“铬废液回收及评价”为例

This paper introduces an experiment about waste liquid recovery and effect evaluation in laboratory. Through this experiment, the basic operations of crystal preparation, chemical analysis and instrumental analysis are further consolidated. At the same time, it allows students to experience a series of possible problems of condition selection and control in the process of waste liquid treatment. We hope to improve the students' ability to analyze and solve problems, enhance their interest in learning, and strengthen their humanistic education.     

Compatibility Studies of Multicomponent Tablet Formulations. DSC and experimental mixture design

An experimental mixture design was applied to a differential scanning calorimetry (DSC) study performed to evaluate naproxen compatibility in tablet formulations consisting of four classic excipients (sorbitol, sodium carboxymethylcellulose, poly(ethylene glycol) 20000 and Veegum) each in adequate concentration ranges accounting for the relevant values actually used in pharmaceutical formulations. Twenty-seven different tablets were obtained from as many mixtures prepared according to the experimental design plan and analyzed in a random order by DSC. Statistical evaluation of experimental data enabled correlation of both enthalpy and onset temperature variations of drug melting endotherm (selected as responses indicative of the presence of drug-excipient interactions) with the mixture composition. Variance analysis (Anova) confirmed the reliability of the postulated polynomial model in providing adequate prediction of true system behaviour. This revised version was published online in August 2006 with corrections to the Cover Date.     

Plasma Thermal Conversion of Methane to Acetylene

This paper describes a re-examination of a known process for the direct plasma thermal conversion of methane to acetylene. Conversion efficiencies (% methane converted) approached 100% and acetylene yields in the 90–95% range with 2–4% solid carbon production were demonstrated. Specificity for acetylene was higher than in prior work. Improvements in conversion efficiency, yield, and specificity were due primarily to improved injector design and reactant mixing, and minimization of temperature gradients and cold boundary layers. At the 60-kilowatt scale cooling by wall heat transfer appears to be sufficient to quench the product stream and prevent further reaction of acetylene resulting in the formation of heavier hydrocarbon products or solid carbon. Significantly increasing the quenching rate by aerodynamic expansion of the products through a converging–diverging nozzle led to a reduction in the yield of ethylene but had little effect on the yield of other hydrocarbon products. While greater product selectivity for acetylene has been demonstrated, the specific energy consumption per unit mass of acetylene produced was not improved upon. A kinetic model that includes the reaction mechanisms resulting in the formation of acetylene and heavier hydrocarbons, through benzene, is described.     

High temperature corrosion behaviour of M(Co,Ni)CrAIY-coatings on high temperature materials-microanalytical investigations

In our former investigations, the phenomenon high temperature corrosion (HTC) was described exemplarily on selected materialcoating combinations for blades of stationary gas turbines, mainly in the temperature region of up to 750° C. To answer the question, in which manner higher gas inlet and/or higher material surface temperature would influence the HTC behaviour, a special analytical technique—the integral layer profile analysis—was introduced to ameliorate concentration profile methods. By examining IN 738 LC specimens with CoCrAlY plasma spray coating, stressed by hot gas at 900° C, the limits of this system are shown by explaining the corrosion mechanism; the method is also used for other systems, e.g. U 520 with NiCrAlY coating at 750° C.     

从静态应力松弛实验求材料准松弛时间谱的一种数值计算方法

避开繁琐困难的函数求解过程，采用数值计算方法，从常规的静态应力松弛实验，直接求被测材料的松弛单元的表现松弛强度．主松弛时间τ０由单－ＭＡＸＷＥＬＬ模型求得，其他松弛时间分别约取为１０（－２）·τ０，１０（－１）·τ０，１０１·τ０，１０３·τ０。应力松弛万程取５参数模型，记为谱的强度ａｉ（或Ａｉ）通过多元线性回归，由最小二乘法确定．对一种天然橡胶试样在不同温度下的松弛曲线进行处理，回归值与原始实验值吻合良好，不同温度下的松弛单元对总松弛的贡献，反映出温度对松弛过程的活化作用．     

性别差异对研发投资决策影响的实验研究

基于Z-Tree实验平台利用研发投资自然博弈实验研究发现风险规避导致女性的研发投入强度低于男性,但女性在研发投资过程中愿意投入的研发努力程度高于男性。随着时间推移,男性的研发努力程度明显下降,但女性的研发努力程度反而上升。男性和女性在决策中均表现出心理账户效应,女性更加愿意通过努力来提高业绩。男性在投资中更多体现期权思想,而女性更多表现出长期倾向下的持续努力。文章在揭示性别因素影响研发投资机理基础上,为董事会性别多样性、分级董事会以及递延薪酬等治理机制发挥作用机理提供了新解释。研究结论可以为企业职位的性别配置、分级董事会以及激励契约设计提供借鉴。关键词:性别差异;研发投资;实验研究;心理账户;风险规避;长期倾向     

Membrane-oxide semiconductor field-effect transistor (MOSFET) sensors

MOSFET-sensors can be considered as membrane-oxide-semiconductor field-effect transistors. MOSFETs can be divided into ISFETs, GasFETs, BioFETs, these sensors being sensitive to ion, gas, biomolecules respectively and there is also a possibility to fabricate MOSFET reference electrode (RefFET). The development and theoretical treatment of various type of MOSFET-sensors are presented in this paper.     

结晶聚合物中间层理论与实验佐证

概述了Ｆｌｏｒｙ和Ｙｏｏｎ由晶格模型出发，从理论上证明了结晶聚合物中间层的存在以及近年来许多学者采用多种实验技术确认中间层存在的事实。