类钙钛矿化合物Ca(Mn2 Cu1)Mn4 O12的磁性与磁电阻效应

利用固相反应法制备了名义成分为Ca(Mn2 Cu1 )Mn4 O1 2 的类钙钛矿锰氧化物 .x射线衍射表明 ,为了获得较为致密的样品和减小杂相含量 ,可以采用高温烧结再在 10 73K长时间空气中退火的制备方法 .样品在低温下同时存在铁磁相和反铁磁相 ,由于反铁磁相的存在导致样品在 4 5K时的磁化强度显著降低 ,并在 8T的高磁场下仍未达到饱和 .样品呈半导体导电性质 ,在 85K和 6T磁场下磁电阻比的最大值可达 - 4 6 % .     

Cl/HN3/I2全气相化学激光体系的化学动力学模拟计算

 对Cl/HN₃/I₂产生NCl(a)/I激光的过程进行了化学动力学计算，主要考察了Cl,HN₃和I₂的初始粒子数密度及其配比对小信号增益系数的影响。结果发现,当温度为400K, 初始Cl粒子数密度为1×10¹⁵，1×10¹⁶和1×10¹⁷cm^-3时,小信号增益系数分别达到1.6×10^-4,1.1×10^-3和1.1×10^-2cm^-1，获得最佳小信号增益系数的HN₃和I₂的初始粒子数密度分别为初始Cl粒子数密度的1～2倍和2%～4%。同时，对Cl，HN₃和I₂配比对小信号增益系数和增益持续时间的影响进行了讨论。     

Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

Acetalation and Ketalation Catalyzed by SO42-/TiO2-MoO3

The catalytic activities of SO42-/TiO2-MoO3 in synthesizing cyclohexanone ethylene ketal,cyclohexanone 1,2-propanediol ketal, 2-propyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane,2-isopropyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane, butanone ethy-lene ketal and butanone 1,2-propanediol ketal were reported. It has been demonstrated that SO42-/TiO2-MoO3 is an excellent catalyst. Various factors concerned in this reaction have been investigated. The optimum conditions have been found, that is, the molar ratio of aldehyde/ketone to alcohol was 1:1.5 or 1:1.3,the mass ratio of the catalyst used to the reactants was 0.25～1.5%, and the reaction time was 45～60 min. Under this conditions, the yield of cyclohexanone ethylene ketal is 82.7%, cyclohexanone 1,2-propanediol ketal is 83.4%, the yield of 2-propyl-1,3-dioxolane is 68.1%,4-methyl-2-isopropyl-1,3-dioxolane is 87.5%, the yield of 2-isopropyl-1,3-dioxolane is 70.7%,4-methyl-2-isopropyl-1,3-dioxolane is 82.5%, the yield of butanone ethylene ketal is 74.1%, and butanone 1,2-propanediol ketal is 94.9%.Some equation and experiment results concerned of the synthetic acetals or ketals were listed as follows.     

Hydrothermal Synthesis and Characterization of a Novel Two-dimensional Framework Materials Constructed from Polyoxometalate and Coordination Groups: [H_2Mo_(5.5)V_(10.5)O_(40)(PO_4)][Cu(en)_2]_4·7H_2O

IntroductionPolyoxometalatesarewidelystudiedfortheirin terestingapplicationsincatalysis ,electronicconduc tivity ,magnetism ,nonlinearopticsandmedicine[1— 4 ] .Whilethemechanismofthesynthesisofpolyoxometalatesremainselusiveandisoftende scribedasself assembly ,thereseemstobeanincreas inguseofthecombinationofthehydrothermalmethodandthestructure directingtemplate .There searchwiththismethodhasdemonstratedthatanum beroftransitionmetaloxides ,typicallyreducedmolybdenumoxides ,mixedvalancevanadiumo…     

Self-assembly of Carboxyl Functionalized Polystyrene Nanospheres into Close-packed Monolayers via Chemical Adsorption

The polyacrylic acid functionalized polystyrene nanospheres were synthesized and self-assembled into irregular, densely packed monolayers in non-aqueous media. The polymer nanoparticles were chemically adhered to substrates. The morphologies of the resulting films were investigated. The impact of the volume fraction of alcohol in the mixed solvents on the particle adsorption and fabrication of nanosphere assembled films was examined.     

Analysis of end point vibrations of a two-link manipulator by integrated CAD/CAE procedures

In this work, the effect of flexibility on the trajectory of a planar two-link manipulator is studied using integrated computer-aided design/analysis (CAD/CAE) procedures. The solid models and finite element models of the parts of the manipulator are created by using the CAD/CAE software I-DEAS. The assembly is defined, and knowing the payload and the end point trajectory, the velocities and accelerations of the parts, joint forces and driving torques are calculated using the rigid body dynamics. All the time dependent nodal forces acting on the parts including distributed gravity and inertia forces are created in files with the I-DEAS program file format. The finite element vibration analysis of the parts is performed by I-DEAS. The end point vibrations and the deviations from the rigid-body trajectory are analyzed for different types of end point acceleration curves. A circular trajectory is considered as an example. It is observed that the precision of the manipulator can be increased by testing different end point acceleration curves without changing the trajectory and the duration of the end point work. The procedure explained in this work can be used for this purpose successfully.     

Non-protein amino acids in peptide design

An overview of the use of non-protein amino acids in the design of conformationally well-defined peptides, based on work from the author’s laboratory, is discussed. The crystal structures of several designed oligopeptides illustrate the useα-aminoisobutyric acid (Aib) in the construction of helices, D-amino acids in the design of helix termination segments and^DPro-Xxx segments for nucleating ofβ-hairpin structures.β- andγ-amino acid residues have been used to expand the range of designed polypeptide structures. Dedicated to Professor C N R Rao on his 70th birthday     

On Modular Forms Arising from a Differential Equation of Hypergeometric Type

Modular and quasimodular solutions of a specific second order differential equation in the upper-half plane, which originates from a study of supersingular j-invariants in the first author's work with Don Zagier, are given explicitly. Positivity of Fourier coefficients of some of the solutions as well as a characterization of the differential equation are also discussed.