射频磁控溅射法生长MgxZn1-xO薄膜的结构和光学特性

用射频磁控溅射法在80℃的衬底温度下制备出Mg_xZn_1-xO(0≤x ≤030)薄膜.x射线 衍射(XRD)结果表明，Mg_xZn_1-xO薄膜为单相六角纤锌矿结构， 没有形成任何显著 的MgO分离相，Mg_xZn_1-xO薄膜的择优取向平行于与衬底垂直的 c轴；c轴晶格常数随着Mg含量的增加逐渐减小.在Mg_xZn_1-xO薄膜的光透射谱中出现 锐利的吸收边，由透 射谱估算出Mg_xZn_1-xO薄膜的带隙宽度由332eV(x=0)线性地 增加到396eV(x=030). 关键词： xZn_1-xO薄膜')" href="#">Mg_xZn_1-xO薄膜 射频磁控溅射 Mg含量     

SIMS depth profiling of semiconductor interfaces: Experimental study of depth resolution function

Reconstruction of original element distribution at semiconductor interfaces using experimental SIMS profiles encounters considerable difficulties because of the matrix effect, sputtering rate change at the interface, and also a sputtering‐induced broadening of original distributions. We performed a detailed depth profiling analysis of the Al step‐function distribution in GaAs/Al_xGa_1?xAs heterostructures by using Cs⁺ primary ion beam sputtering and CsM⁺ cluster ion monitoring (where M is the element of interest) to suppress the matrix effect. The experimental Depth Resolution Function (DRF) was obtained by differentiation of the Al step‐function profile and compared with the ‘reference’ DRF found from depth profiling of an Al delta layer. The difference between two experimental DRFs was explained by the sputtering rate change during the interface profiling. We experimentally studied the sputtering rate dependence on the Al_xGa_1?xAs layer composition and applied it for a reconstruction of the DRF found by differentiating the Al step‐function distribution: the ‘reconstructed’ and ‘reference’ DRFs were found to be in good agreement. This confirmed the correctness of the treatment elaborated. Copyright © 2010 John Wiley & Sons, Ltd.     

Magnetron sputtering Si interlayer: a protocol to prepare solid phase microextraction coatings on metal-based fiber

Use of metal fibers in solid phase microextraction (SPME) can overcome the fragility drawback of conventional fused-silica ones. However, the surface modification of metal substrates is rather difficult, which largely prevents many mature traditional techniques, such as sol-gel and chemical bonding, being used in fabrication of SPME coating on metal-based fibers. This study demonstrates a protocol to resolve this problem by magnetron sputtering a firm Si interlayer on stainless steel fiber. The Si interlayer was easily modified active group, and attached with a multiwalled carbon nanotubes (MWCNTs) coating using the reported approach. The as-prepared MWCNTs/Si/stainless steel wire fiber not only preserved the excellent SPME behaviors of MWCNTs coatings, but also exhibited a number of advantages including high rigidity, long service life, and good stability at high temperature, in acid and alkali solutions. This new surface modification technique might provide a versatile approach to prepare sorbent coatings on unconfined substrates using traditional methods.     

Studies on the resistance switching properties of the La0.5Ca0.5MnO3/Nb : SrTiO3 heterojunction

In this study, we have investigated the resistance switching behavior of the La_0.5Ca_0.5MnO₃/Nb:SrTiO₃ heterojunction. The junction shows a negative resistance switching ratio (ER) below 140 K. When , the ER goes from negative to positive with increasing bias voltage. When T>220 K, the junction shows a positive ER. This variation from a negative to a positive value indicates that the ER is determined primarily by two phenomena: (a) the negative ER value can be attributed to a disruption of the charge-ordered insulating domains in La_0.5Ca_0.5MnO₃ under large electric fields, and (b) the positive ER value at high temperatures is due to the modulation of the interface barrier width driven by the electrochemical migration of oxygen vacancies.     

Effect of different annealing methods on ferroelectric properties of 0.95Pb(Sc0.5Ta0.5)O3-0.05PbTiO3 thin films

0.95Pb(Sc_0.5Ta_0.5)O₃-0.05PbTiO₃ thin films were prepared on LaNiO₃/SiO₂/Si substrate by radio frequency magnetron sputtering, and the films were annealed subsequently with repeated many times by two approaches: normal one-step rapid thermal annealing and innovative two-steps rapid thermal annealing. X-ray diffraction demonstrates that all the films were preferred (1 0 0) oriented and an appropriate repeat of annealing process can enhance perovskite phase of the films. Scanning electron microscopy suggests that the films treated by two-steps rapid thermal annealing show crack-free, uniform size grains and dense microstructure. Measurement of remnant polarization and leakage current dependence of electric field confirms that the films treated by two-steps rapid thermal annealing exhibit better ferroelectric properties than the films treated by one-steps rapid thermal annealing. The results reveal that microstructure plays an important role in enhanced ferroelectric properties of the 0.95Pb(Sc_0.5Ta_0.5)O₃-0.05PbTiO₃ thin films.     

Effect of RF power and sputtering pressure on the structural and optical properties of TiO2 thin films prepared by RF magnetron sputtering

TiO₂ thin films were deposited onto quartz substrates by RF magnetron sputtering. The samples deposited at various RF powers and sputtering pressures and post annealed at 873 K, were characterized using X-ray diffraction (XRD), micro Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), UV-vis spectroscopy and photoluminescence (PL) spectroscopy. XRD spectrum indicates that the films are amorphous-like in nature. But micro-Raman analysis shows the presence of anatase phase in all the samples. At low sputtering pressure, increase in RF power favors the formation of rutile phase. Presence of oxygen defects, which can contribute to PL emission is evident in the XPS studies. Surface morphology is much affected by changes in sputtering pressure which is evident in the SEM images. A decrease in optical band gap from 3.65 to 3.58 eV is observed with increase in RF power whereas increase in sputtering pressure results in an increase in optical band gap from 3.58 to 3.75 eV. The blue shift of absorption edge in all the samples compared to that of solid anatase is attributed to quantum size effect. The very low value of extinction coefficient in the range 0.0544-0.1049 indicates the excellent optical quality of the samples. PL spectra of the films showed emissions in the UV and visible regions.     

Nano-scale and surface precipitation of metallic particles in laser interference patterned noble metal-based thin films

Laser interference patterning (also known as “laser interference metallurgy”) is used to locally tailor the microstructure of oxide (Pd_0.25Pt_0.75O_x) and nitride (Cu₃N) thin films to induce a chemical decomposition, which is responsible for a decrease of electrical resistivity. This technique allows hereby a laser-induced chemical decomposition of as-deposited oxide and nitride films, resulting locally in a porous microstructure due to the simultaneous emission of gaseous nitrogen and oxygen. The process locally generates at the nanometer scale metal precipitatation of Pt or Cu in the oxide or nitride matrix. Thus, isolated metallic clusters with low resistivity coexist with a high resistivity phase, establishing a preferential electrical conduction path and giving the system a lower effective resistivity. The decomposition process is investigated by four-point probe method, X-ray diffraction, spectrophotometry, white light interference, scanning and transmission electron microscopies.     

125 MeV Si ion irradiation of calcium phosphate thin film coated by rf-magnetron sputtering technique

Titanium substrate was coated with hydroxyapatite by radiofrequency magnetron sputtering (rf-magnetron sputtering) technique and subjected to swift heavy ion (SHI) irradiation of 125 MeV with Si⁹⁺ at fluences of 1 × 10¹⁰, 1 × 10¹¹ and 1 × 10¹² ions/cm². The glancing incidence X-ray diffraction (GIXRD) analysis confirmed the HAp phase of the irradiated film. There was a considerable decrease in crystallinity and particle size after irradiation. In addition, DRS-UV reflectance spectra revealed a decrease in optical band gap (E_g) from 5.2 to 4.6 eV. Wettability of biocompatible materials plays an important role in biological cells proliferation for tissue engineering, drug delivery, gene transfer and bone growth. HAp thin films irradiated with 1 × 10¹¹ ions/cm² fluence showed significant increase in wettability. While the SHI irradiated samples exhibited enhanced bioactivity, there was no significant variation in cell viability. Surface roughness, pores and average particle size were analyzed by atomic force microscopy (AFM).     

Characterization and properties Ti-Al-Si-N nanocomposite coatings prepared by middle frequency magnetron sputtering

TiN-containing amorphous Ti-Al-Si-N (nc-TiN/a-Si₃N₄ or a-AlN) nanocomposite coatings were deposited by using a modified closed field twin unbalanced magnetron sputtering system which is arc assisted and consists of two circles of targets, at a substrate temperature of 300 °C. XRD, XPS and High-resolution TEM experiments showed that the coatings contain TiN nanocrystals embedded in the amorphous Si₃N₄ or AlN matrix. The coatings exhibit good mechanical properties that are greatly influenced by the Si contents. The hardness of the Ti-Al-Si-N coatings deposited at Si targets currents of 5, 8, 10, and 12 A were 45, 47, 54 and 46 GPa, respectively. The high hardness of the deposited Ti-Al-Si-N coatings may be own to the plastic distortion and dislocation blocking by the nanocrystalline structure. On the other hand, the friction coefficient decreases monotonously with increasing Si contents. This result would be caused by tribo-chemical reactions, which often take place in many ceramics, e.g. Si₃N₄ reacts with H₂O to produce SiO₂ or Si(OH)₂ tribolay-layer.