脂松香、石炭酸松香树脂和马林酸松香树脂的红外光谱剖析及鉴别

本文对脂松香、石炭酸松香树脂和马林酸松香树脂的红外光谱剖析及鉴别，方法快速，简便，准确。     

MORPHOLOGY OF BLACK CARBON AEROSOLS AND UBIQUITY OF 50-NANOMETER BLACK CARBON AEROSOLS IN THE ATMOSPHERE

Different-sized aerosols were collected by an Andersen air sampler to observe the detailed morphology of the black carbon （BC） aerosols which were separated chemically from the other accompanying aerosols, using a Scanning Electron Microscope equipped with an Energy Dispersive X-ray Spectrometer （SEM-EDX）. The results indicate that most BC aerosols are spherical particles of about 50 nm in diameter and with a homogeneous surface. Results also show that these particles aggregate with other aerosols or with themselves to form larger agglomerates in the micrometer range. The shape of these 50-nm BC spherical particles was found to be very similar to that of BC particles released from petroleum-powered vehicular internal combustion engines. These spherical BC particles were shown to be different from the previously reported fullerenes found using Matrix-Assisted Laser Desorption/Ionization Time-Of-Flight Mass Spectrometry （MALDI-TOF-MS）.     

Reintroduced solids increase inhibitor levels in a pretreated corn stover hydrolysate

Following detoxification of the liquid hydrolysate produced in a corn stover pretreatment process, inhibitor levels are seen to increase with the re-addition of solids for the ensuing hydrolysis and fermentation processes. The solids that were separated from the slurry before detoxification of the liquor contain approx 60% (w/w) moisture, and contamination occurs owing to the diffusion of inhibitors from the moisture entrained in the porous structure of the corn stover solids into the bulk fluid. This evidence suggests the need for additional separation and detoxification steps to purge residual inhibitors entrained in the moisture in the solids. An overliming process to remove furans from the hydrolysate failed to reduce total organic acids concentration, so acids were removed by treatment with an activated carbon powder. Smaller carbon doses proved more efficient in removing organic acids in terms of grams of acid removed per gram of carbon powder. Sugar adsorption by the activated carbon powder was minimal.     

Effects of Moisture and Stresses on the Structure and Properties of Polyester Resin

The results of a complex study of structural changes in a cured Norpol 440 polyester resin under the action of damp environment and mechanical loading are presented. A considerable effect of absorbed moisture on the structure and some characteristics of the material is revealed by using thermophysical methods and X-ray diffractometry. The joint effect of moisture and mechanical stress is estimated by investigating the creep in stationary and nonstationary moisture conditions. The anisotropy of the material structure formed during creep is evaluated from the results of dilatometric measurements. It is found that the degree of anisotropy of the material after creep accompanied by moisture sorption is higher than that after creep in the conditions of moisture equilibrium with atmosphere. It is established that the aftercure and relaxation of the residual creep deformation come to an end at heating to 80-85°C. At a further rise in temperature and repeated heating, changes in the material structure are not observed.     

Fabrication and transport properties of multiwall carbon nanotube crossroads

A multiwall carbon nanotube crossroads has been fabricated by a manipulation technique using a glass microcapillary, and the low temperature transport properties investigated. The two-terminal conductance of an individual tube shows Tomonaga–Luttinger liquid behavior G∝T^α at high temperature and dI/dV ∝V ^α at low temperature. However, no evidence of such a power-law behavior is obtained in the four-terminal conductance at the junction, where the conductance shows an almost metallic behavior ‘corrected’ by weak localization. Weak localization would essentially appear in electron states at the junctions of MWNTs.     

Speciation Analysis of Inorganic Tin (Sn(II)/Sn(IV)) by Graphite Furnace Atomic Absorption Spectrometry Following Ion-Exchange Separation

A new method based on anion exchange resin separation and graphite furnace atomic absorption spectrometry (GFAAS) detection is proposed for the determination of inorganic tin species. The result showed that Sn(IV) was quantitatively retained on the resin when [HCl] = 9.0 mol · L⁻¹, but Sn(II) could not be adsorbed on the resin under the same condition. Thus, a separation of Sn(II) and Sn(IV) has been realized. When the concentration of NaOH solution was between 2.0–7.0 mol · L⁻¹, Sn(IV) that adsorbed on the resin could be eluated from the resin completely. Meanwhile, under the atmosphere and the nitrogen states, the translation between Sn(II) and Sn(IV) was investigated. Under the optimal conditions, the detection limit of Sn(IV) is 0.40 μg · L⁻¹ with RSD of 2.3% (n = 5, c = 2.0 μg · L⁻¹). The proposed method was applied to the speciation analysis of tin in different water samples and the recovery of total Sn was in the range of 98.7–101.7%. In order to verify the accuracy of the method, a certified reference water sample was analyzed and the results obtained were in good agreement with the certified value.     

Covalent functionalization of multi-walled carbon nanotubes by lipase

Lipase from Candida rugosa was covalently anchored onto acid-treated multi-walled carbon nanotubes (MWNTs) through a self-catalytic mechanism. A variety of characterization techniques including FTIR, Raman spectroscopy, and XPS were employed to demonstrate the formation of the ester linkage between lipase and MWNTs. The MWNTs-lipase biocomposites showed significantly increased solubility in some common-used organic solvents, such as THF, DMF and chloroform. This study may offer a novel and facile route for covalent modification of carbon nanotubes, and expand the potential utilization of both lipases and MWNTs in the fields of biocatalyst and biosensor.     

Nanometric Antimony Powder Synthesis by Activated Alkaline Hydride Reduction of Antimony Pentachloride

A novel chemical reduction method using an activated alkaline hydride (LiH or NaH-t-BuONa) in tetrahydrofuran solvent has been applied to antimony salt reduction. X-ray diffraction and transmission electron microscopy studies have been carried out to characterize the morphology and structure of the materials. Alkali hydride nature influence has been proved. In both cases the process allows to prepare antimony particles in nanometer range from few nanometers to about 20nm which could be used as anodic materials for lithium–ion batteries. With lithium hydride well-crystallized particles inclined to agglomeration were observed whereas finely dispersed amorphous particles were pointing out after activated sodium hydride reduction.     

脉冲磁场处理对碳纳米管掺杂MgB2线材临界电流密度的影响

对碳纳米管(CNT)掺杂MgB₂超导体磁场处理后的行为进行了研究. 结果表明，CNT掺杂MgB₂超导体经5T脉冲磁场处理后临界电流密度J_c(H)在低磁场下提高了2—3倍，高场下提高一个数量级以上，扫描电镜结果显示CNT沿着处理磁场方向规则排列并且成为MgB₂基体的形核中心和高效的磁通钉扎中心. 关键词： 2')" href="#">MgB₂ 碳纳米管 脉冲磁场处理