Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

Thermal conductance for single wall carbon nanotubes

We report a theoretical analysis of the phonon thermal conductance, κ(T), for single wall carbon nanotubes (SWCN). In a range of low temperatues up to 100 K, κ(T) of perfect SWCN is found to increase with temperature, approximately, in a parabolic fashion. This is qualitatively consistent with recent experimental measurements where the tube-tube interactions are negligibly weak. When the carbon-carbon bond length is slightly varied, κ(T) is found to be qualitatively unaltered which implies that the anharmonic effect does not change the qualitative behavior of κ(T). Received 12 June 2001     

广义复合隐迭代格式逼近非扩张映像公共不动点

提出并使用如下广义复合隐迭代格式逼近非扩张映像族{Ti}Ni=1公共不动点:{xn=αnxn-1 (1-αn)Tnyn,yn=rnxn snxn-1 tnTnxn wnTnxn-1,rn sn tn wn=1,{αn},{rn},{sn},{tn},{wn}∈[0,1],这里Tn=TnmodN.该文提出的广义复合隐迭代格式包含了目前多种迭代格式,因此,所得强弱收敛定理推广及发展了Mann,Ishikawa,XuandOri,等许多作者的结果.     

Transfer matrix approach of vibration isolation analysis of periodic composite structure

The transmission properties of elastic waves propagating in a three-dimensional composite structure embedded periodically with spherical inclusions are analyzed by the transfer matrix method in this paper. Firstly, the periodic composite structures are divided into many layers, the transfer matrix of monolayer structure is deduced by the wave equations, and the transfer matrix of the entire structure is obtained in the case of boundary conditions of displacement and stress continuity between layers. Then, the effective impedance of the structure is analyzed to calculate its reflectivity and transmissivity of vibration isolation. Finally, numerical simulation is carried out; the experiment results validate the accuracy and feasibility of the method adopted in the paper and some useful conclusions are obtained. Project (No. 50075029) supported by the National Natural Science Foundation of China.     

Solvothermal Synthesis of Molybdenum Disulfide Hollow Spheres Modified by Cyanex 301 in Water–Ethanol Medium

Hollow spherical molybdenum disulfide has been successfully synthesized via a solvothermal method using Cyanex 301 as sulfur source and modification agent. The hollow spheres are characterized by transmission electron microscopy, scanning electron microscopy, X-ray diffraction and Energy-Dispersive X-ray analysis. The influences of reaction conditions are also discussed while a mechanism is proposed to explain the formation of the peculiar morphology.     

Nanometric Antimony Powder Synthesis by Activated Alkaline Hydride Reduction of Antimony Pentachloride

A novel chemical reduction method using an activated alkaline hydride (LiH or NaH-t-BuONa) in tetrahydrofuran solvent has been applied to antimony salt reduction. X-ray diffraction and transmission electron microscopy studies have been carried out to characterize the morphology and structure of the materials. Alkali hydride nature influence has been proved. In both cases the process allows to prepare antimony particles in nanometer range from few nanometers to about 20nm which could be used as anodic materials for lithium–ion batteries. With lithium hydride well-crystallized particles inclined to agglomeration were observed whereas finely dispersed amorphous particles were pointing out after activated sodium hydride reduction.     

Thermal and chemical nanofractal relaxation

We studied shape relaxation of nano-fractal islands, during annealing, after their growth from antimony cluster deposition on graphite surface. Annealing at 180^°C shows evidence of an increase of the fractal branch width with time followed by branch fragmentation, without changing the fractal dimension. The time evolution of the width of the arm suggests the surface self-diffusion mechanism as the main relaxation process. With Monte Carlo simulations, we confirmed the observed behavior. Comparison is done with our previous results on fragmentation of nano-fractal silver islands when impurity added to the incident cluster promotes rapid fragmentation by surface self-diffusion enhancement [1].     

Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007     

A comparative study on the interaction between tin(II) porphyrin and selected group 8B metals for potential application as reduction catalysts

We study the interaction between tin(II) porphyrin (SnPor) with platinum and non-precious Group 8B metals (iron, cobalt and nickel) by density functional theory and discuss the electronic properties of the resulting products. We also model the interaction of the resulting compounds with water where applicable. Our studies indicate that, SnPor-Ni possesses electronic properties similar to SnPor-Pt, suggesting that it may possess similar photocatalytic properties for reduction reactions, such as converting water to hydrogen gas.