Zn_(2-x)GeO_(4-x-3y)N_(2y)催化剂的制备、表征及可见光催化性能

通过氮化Zn2GeO4制备了Zn2-xGeO4-x-3yN2y催化剂,其带边吸收由400nm的紫外光区扩展到600nm的可见光区。光催化产氧性能的结果表明,氮化温度为800℃时,制备的催化剂具有最大活性。不同助催化剂对产氧活性的影响研究表明,担载助催化剂能大大提高产氧活性,其中担载Co2O3的产氧活性可达未担载的3.8倍。     

Photocatalytic Activities for Water Splitting of RuO_2-loaded MGa_2O_4（M=Zn,Ni） with d~（10） Configuration

MGa2O4(M=Zn,Ni) rods with similar crystallinity and BET surface area were prepared via a facile template-engaged reaction.The photocatalytic activities for water splitting of RuO2-loaded MGa2O4(M=Zn,Ni) were investigated under high-pressure Hg lamp.RuO2-loaded ZnGa2O4 catalyst exhibited much higher photocatalytic activity than RuO2-loaded NiGa2O4.Factors affecting the photocatalytic activities of RuO2-loaded MGa2O4(M=Zn,Ni) were discussed.It was suggested that the electronic structure of oxide semiconductor was a predominant factor of the photocatalytic behavior for RuO2-loaded MGa2O4(M=Zn,Ni).     

聚苯胺/Co_(0.5)Zn_(0.5)Fe_2O_4纳米复合材料的制备及电磁性能

采用高分子凝胶法制备尖晶石型Co0.5Zn0.5Fe2O4,原位聚合法制备纯聚苯胺和聚苯胺/Co0.5Zn0.5-Fe2O4纳米复合材料.使用傅立叶红外光谱(FTIR)、紫外可见吸收光谱(UV-Vis)、X射线衍射仪(XRD)和透射电子显微镜(TEM)对复合材料进行了表征.FTIR和XRD的结果表明样品为纯聚苯胺和聚苯胺/Co0.5Zn0.5-Fe2O4.UV-Vis光谱表明聚苯胺/Co0.5Zn0.5Fe2O4苯环上的π-π*和n-π*分别红移了23nm和5nm.TEM照片可知,聚苯胺和聚苯胺/Co0.5Zn0.5Fe2O4粒子的平均粒径分别约为50nm和70nm.在8.2～12.4GHz测试频率范围内,聚苯胺/Co0.5Zn0.5Fe2O4的ε″数值在9.2～12.3之间,u″数值在0.15～0.16之间;聚苯胺/Co0.5-Zn0.5Fe2O4介电损耗低于纯聚苯胺,而磁损耗高于纯聚苯胺.     

Effect of indium content and rapid solidification on microhardness and micro‐creep of Sn‐Zn eutectic lead free solder alloy

The Sn‐Zn alloys have been considered as lead‐free solders. In this paper, the effect of 0.0, 0.5, 1.0, 1.5 and 2.0 wt.% Indium as ternary additions on melting temperature, structure, microhardness and micro‐creep of the Sn‐9Zn lead‐free solders were investigated. It is shown that the alloying additions of Indium to the Sn‐Zn binary system result in a suppression of the melting point to 187.9 °C. From x‐ray diffraction analysis, a new intermetallic compound phase, designated β‐In₃Sn is detected. The formation of an intermetallic compound phase causes a pronounced increase in the electrical resistivity and mechanical strength. Also, an interesting connection between dynamic Young's modulus and the axial ratio (c/a) of the unit cell of the β‐Sn was found in which Young's modulus increases with increasing the axial ratio (c/a). The ternary Sn‐9Zn‐xIn exhibits creep resistance superior to Sn‐9Zn binary alloy. The better creep resistance of the ternary alloy is attributed to solid solution effect and precipitation of In₃Sn in the Sn matrix. The addition of small amounts of In is found to refine the effective grain size and consequently, improves hardness. The 89%Sn‐9%Zn‐2%In alloy is a lead‐free solder designed for possible drop‐in replacement of Pb‐Sn solders. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Fabrication of CuO/T-ZnOw nanocomposites using photo-deposition and their photocatalytic property

CuO/tetrapod-like ZnO whisker (T-ZnOw) nanocomposites were successfully synthesized using a simple photo-deposition method. Some nanocomposites exhibit remarkably improved photocatalytic property, while the extents of the improvements vary with different Cu/Zn molar ratios and polyethylene glycol (PEG) concentrations. Moreover, it is found that excessively high Cu/Zn molar ratio or PEG concentration would reduce the photocatalytic property of the nanocomposites. A direct relationship between the morphology and the photocatalytic property of CuO/T-ZnOw was established and then analyzed by discussing the photocatalytic mechanism of the CuO/T-ZnOw nanocomposites.     

Facile fabrication of Zn/Zn5(OH)8Cl2·H2O flower-like nanostructure on the surface of Zn coated with poly (N-methyl pyrrole)

Zn/Zn₅(OH)₈Cl₂·H₂O flower-like nanostructures was electrodeposited on the coated Zn with poly (N-methyl pyrrole) in 0.1 M Zn (NO₃)₂ and 0.1 M KCl solution. The morphology and the structure of the Zn/Zn₅(OH)₈Cl₂·H₂O were characterized by Field Emission Scanning Electron Microscopy (FESEM), Fourier transform infrared (FT-IR) spectroscopy and X-ray diffraction analysis (XRD). The FT-IR results showed special peaks at 908 and 728 cm⁻¹ related to Zn₅(OH)₈Cl₂·H₂O. The FESEM results indicated that Zn/Zn₅(OH)₈Cl₂·H₂O consists of a flower-like nanostructure and these flower-shaped structures contain many shaped nanopetals with the thickness of 27.8 nm. The XRD result confirmed that the major phase of electrodeposited product in 0.1 M KCl as supporting electrolyte was Zn₅(OH)₈Cl₂·H₂O. The ability of PMPy to create a thin film and the existence of several pores in its matrix act as a mold for the growth of Zn/Zn₅(OH)₈Cl₂·H₂O flower-like nanostructure. The trapping of Cl⁻ and OH⁻ within pores can be considered as the reason for the formation of flowerlike Zn/Zn₅(OH)₈Cl₂·H₂O nanostructures in 0.1 M KCl.     

Theoretical study of cisplatin adsorption on silica

The adsorption of cisplatin and its complexes, cis-[PtCl(NH₃)₂]⁺ and cis-[Pt(NH₃)₂]²⁺, on a SiO₂(1 1 1) hydrated surface has been studied by the Atom Superposition and Electron Delocalization method. The adiabatic energy curves for the adsorption of the drug and its products on the delivery system were considered. The electronic structure and bonding analysis were also performed. The molecule-surface interactions are formed at expenses of the OH surface bonds. The more important interactions are the Cl-H bond for cis-[PtCl₂(NH₃)₂] and cis-[PtCl(NH₃)₂]⁺ adsorptions, and the Pt-O interaction for cis-[Pt(NH₃)₂]²⁺ adsorption. The Cl p orbitals and Pt s, p y d orbitals of the molecule and its complexes, and the s H orbital and, the s and p orbitals of the O atoms of the hydrated surface are the main contribution to the surface bonds.     

广义Carmichael数

设n是一个合数,Z_n表示模n的剩余类环,r(x)∈Z_n[x]是一个首一的k(>0)次不可约多项式。本文引入n是k阶摸r(x)的Carmichael数的定义,全体这样的数记为集C_(k,r)(x),由此给出k阶Carmichael数集:C_k={∪C_(k,r)(x)|r(x)过全体Z_n上的首一k次不可约多项式}。显然C_1表示通常的Carmichael数集。作者得到了n∈C_(k,r(x))的一个充要条件,进而得到n∈C_k的一个充要条件及n∈C_2的一个更易计算的充要条件,还证明了C_1(?)C_2以及|C_2|=∞。     

Zn[(L)Proline]2: an eligible candidate for the synthesis of xanthenediones in water

An efficient route for the condensation of aldehydes with dimedone in the presence of Zn[(L)Proline]₂ in water has been reported. Hydrophilicity of the catalyst is the main attribute of this reaction. The water‐mediated reaction using catalytic amounts of recyclable catalyst avoids the use of expensive, corrosive reagents and toxic solvents and provides operational simplicity. Moreover, column chromatography and recrystallization of product are not required as the crude products itself are very pure and hence can be used for target‐oriented synthesis on a large scale. Copyright © 2012 John Wiley & Sons, Ltd.