980 nm激发下Er3+/Yb3+共掺杂ZrO2-Al2O3粉末的上转换发光特性

通过固相反应法制备了Er3+/Yb3+共掺杂ZrO2-Al2O3粉末的样品,并对样品在980nm激光激发下的上转换发光特性进行了研究.从发射光谱可以发现,在可见光范围内有3个强的发光带,一个位于654nm附近的红光带和两个分别位于545nm、525nm附近的绿光带,分别对应于Er3+离子的以下辐射跃迁:4F9/2→4I15/2、4S3/2→4I15/2、2H11/2→4I15/2.其中又以Er3+离子的4F9/2→4I15/2跃迁产生的红色荧光辐射最强.对其上转换发光机制进行了分析,发现这三个发光过程都是双光子过程.对样品粉末进行了XRD检测,发现ZrO2主要以立方相为主,并且计算得到了这种立方结构的晶格常数.Al2O3固溶于ZrO2中,Al3+嵌入ZrO2后产生氧空位,导致ZrO2晶体的对称性降低,这种结构变化更有利于提高上转换效率,即上转换发光强度增强.     

恒流应力下E2PROM隧道氧化层的退化特性研究

在电容测量的基础上研究了薄隧道氧化层在恒定Fowler-Nordheim(F-N)隧穿电流下的退化情况. 这种退化是恒流应力和时间的函数，对恒流应力大小的依赖性更加强烈，隧道氧化层在F-N电流下的退化是注入电荷密度(Q_inj)的函数. 在较低Q_inj下氧化层中发生正电荷俘获，在较高Q_inj下发生负电荷俘获，导致栅压变化的反复. 关键词： 2PROM')" href="#">E²PROM 隧道氧化层 退化 恒流应力     

B_2分子X~3Σ_g~-和A~3Σ_u~-态的势能函数

使用SAC/SAC-CI方法,利用D95(d),6-311g**以及cc-PVTZ等基组,对B2分子的基态(X3Σg-)和第一激发态(A3Σu-)的平衡结构和谐振频率进行了优化计算.通过对3个基组的计算结果的比较,得出了D95(d)基组为3个基组中的最优基组的结论;使用D95(d)基组,利用SAC的GSUM(Group Sum of Operators)方法对基态(X3Σg-),SAC-CI的GSUM方法对激发态(A3Σu-)进行单点能扫描计算,用正规方程组拟合Murrell-Sorbie函数,得到了相应电子态的完整势能函数;从得到的势能函数计算了与基态(X3Σg-)和第一激发态(A3Σu-)相对应的光谱常数(Be,αe,ωe和ωeχe),结果与实验数据吻合.     

LD泵浦Nd∶LuVO4/Cr4+∶YAG被动调Q激光器

采用大功率半导体激光器端面泵浦Nd∶LuVO4晶体，利用Cr4+∶YAG晶体作为可饱和吸收元件，实现了1.06 μm激光的被动调Q运转.在泵浦功率为19.1 W时，获得最高平均输出功率为4.58 W，脉冲宽度为84 ns，单脉冲能量为36.6 μJ以及峰值功率为436.2 W的激光脉冲.     

Surface structures formed by individual adsorption and coadsorption of Mn and Bi on Cu(0 0 1), studied by LEED

We have studied the individual adsorption of Mn and Bi, and their coadsorption on Cu(0 0 1) by low-energy electron diffraction (LEED). For Mn, we have determined the c(2 × 2) structure formed at 300 K, whose structure had been determined by several methods. We reconfirmed by a tensor LEED analysis that it is a substitutional structure and that a previously reported large corrugation (0.30 Å) between substitutional Mn and remaining surface Cu atoms coincides perfectly with the present value. In the individual adsorption of Bi, we have found a c(4 × 2) structure, which is formed by cooling below ∼250 K a surface prepared by Bi deposition of ∼0.25 ML coverage at 300 K where streaky half-order LEED spots appear. The c(4 × 2) structure has been determined by the tensor LEED analysis at 130 K and it is a substitutional structure. In the coadsorption, we found a c(6 × 4) structure, which has been determined by the tensor LEED analysis. It is very similar to the previously determined structure of the c(6 × 4) formed by coadsorption of Mg and Bi, and embedded MnBi₄ clusters are arranged in the top Cu layer instead of MgBi₄. Large lateral displacements of Bi atoms in the c(6 × 4)-(Mn + Bi) suggest that the Mn atoms undergo the size-enhancement caused by their large magnetic moment.     

The AB2-XA1 electronic transition of NO2: A rovibronic survey covering 14 300-18 000 cm

More than 250 rotationally resolved vibrational bands of the A²B₂-X²A₁ electronic transition of ¹⁵NO₂ have been observed in the 14 300-18 000 cm⁻¹ range. The bands have been recorded in a recently constructed setup designed for high resolution spectroscopy of jet cooled molecules by combining time gated fluorescence spectroscopy and molecular beam techniques. The majority of the observed bands has been rotationally assigned and can be identified as transitions starting from the vibrational ground state or from vibrationally excited (hot band) states. An exceptionally strong band is located at 14 851 cm⁻¹ and studied in more detail as a typical benchmark transition to monitor ¹⁵NO₂ in atmospheric remote sensing experiments. Standard rotational fit routines provide band origins, rotational and spin rotation constants. A subset of 177 vibronic levels of ²B₂ vibronic symmetry has been analyzed in the energy range between 14 300 and 17 250 cm⁻¹, in terms of integrated density and using Next Neighbor Distribution. It is found that the overall statistical properties and polyad structure of ¹⁵NO₂ are comparable to those of ¹⁴NO₂ but that the internal structures of the polyads are completely different. This is a direct consequence of the X²A₁-A²B₂ vibronic mixing.     

Roles of SiH4 and SiF4 in growth and structural changes of poly-Si films

The structural properties of polycrystalline silicon films, prepared by plasma enhanced chemical vapor deposition system, with different flow rates of SiH₄/SiF₄ mixtures at 300 °C were investigated. This study indicates that the low hydrogen coverage on the growing surface, under optimum fluorine radicals, will be leaded to an improvement of crystallized area as compared with case of high hydrogen coverage surface. Moreover, the studies of the role of SiH₄ and SiF₄ radicals show that the SiH₄ radicals are important in the nucleation and growth of grains. However, SiF₄ radicals are effective in the structural change of grain boundaries regions and by this way, in the present system, establish the growth of grains under the dominant 〈1 1 0〉 direction. The stress investigation indicates that addition of high flow rate of SiF₄ in amorphous film, results in the nearly stress free films. Finally, we found that the changes in g-value reflect the changes in the intrinsic compressive and tensile stress in the both polycrystalline and amorphous silicon films.     

Solid-phase epitaxy of CaSi2 on Si(1 1 1) and the Schottky-barrier height of CaSi2/Si(1 1 1)

Thin Ca films were evaporated on Si(1 1 1) under UHV conditions and subsequently annealed in the temperature range 200–650 °C. The interdiffusion of Ca and Si was examined by ex situ Auger depth profiling. In situ monitoring of the Si 2p core-level shift by X-ray photoemission spectroscopy (XPS) was employed to study the silicide formation process. The formation temperature of CaSi₂ films on Si(1 1 1) was found to be about 350 °C. Epitaxial growth takes place at T≥400 °C. The morphology of the films, measured by atomic force microscopy (AFM), was correlated with their crystallinity as analyzed by X-ray diffraction (XRD). According to measurements of temperature-dependent I–V characteristics and internal photoemission the Schottky-barrier height of CaSi₂ on Si(1 1 1) amounts to qΦ_Bn=0.25 eV on n-type and to qΦ_Bp=0.82 eV on p-type silicon.     

HgCl2/I2复合催化剂协同催化合成异丙醇钇的研究

以金属钇和异丙醇为原料，以HgCl2/I2为复合催化剂，通过对金属钇的机械加工以增加其比表面，并将异丙醇脱水使其含水量降低至0．05％，体系在82℃回流5h，经过滤、减压蒸馏，得到了白色海绵状异丙醇钇，其产率高达83％，合成时间比文献报道的缩短了19h，产率提高了8％。文章确定了催化剂的最佳用量为20gY加入60mg HgCl2/I2，研究了合成产率与HgCl2/I2催化剂和HgCl2催化剂的依赖关系及异丙醇中含水量对合成产率的影响，并对HgCl2/I2的催化作用机理进行了初步探讨。     

SEPARATING SCN~- FROM DESULPHURIZATION WASTE SOLUTION OF COCKING PLANT BY D241 RESIN

1. INTRODUCTION In the process of coking plant, about 30%~35% sulfur is transformed to H2S and some other sulfide, which form impurity in coal gas together with NH3 and HCN. Only 0.1% H2S containing in air can lead to die, so it is very important to carry on desulphurization and decyanation with coal gas [1~3]. Currently desulphurization and decyanation craft technique have Dry Oxidation Technology, Wet Oxidation Technology and Liquid Absorption Technology [2] three main kinds. The…