Determination of 48 fragrance allergens in toys using GC with ion trap MS/MS

This paper presents a method for the simultaneous determination of 48 fragrance allergens in four types of toys (plastic toys, play clays, plush toys, and paper toys) based on GC with ion trap MS/MS. Compared with single‐stage MS, MS/MS is superior in terms of the qualification and quantification of a large range of compounds in complicated matrices. Procedures for extraction and purification were optimized for each toy type. The method proved to be linear over a wide range of concentrations for all analytes with correlation coefficients between 0.9768 and 0.9999. Validation parameters, namely, LODs and LOQs, ranged from 0.005–5.0 and from 0.02–20 mg/kg, respectively. Average recoveries of target compounds (spiked at three concentration levels) were in the range of 79.5–109.1%. Intraday and interday repeatabilities of the proposed method varied from 0.7–10.5% and from 3.1–13.4%, respectively. The proposed method was used to monitor fragrance allergens in commercial toy products. Our findings indicate that this method is an accurate and effective technique for analyzing fragrance allergens in materials composed of complex components.     

Study on the Synthesis and Bioactivity of Novel Mahkoside A Derivatives

Abstract

A series of novel Mahkoside A derivatives was synthesized, and their in vitro cytotoxic activities were evaluated against the human cancer cell line Ec‐9706. A Preliminary structure–activity relationship study showed compounds 7 and 8 have obvious cytotoxic activities (IC₅₀: 30.0 and 12.5 µg · mL^?1, respectively).     

Evolution and solar modulation of 7Be during the solar cycle 23

The modulation of ⁷Be-aerosols concentration due to solar activity during the cycle 23 is studied in the present research. For that purpose, was analyzed the differences in the long-term variation of geomagnetic and solar activity to assess the physical effects over the evolution of ⁷Be during the period 1996–2010. Furthermore, exploratory data analysis was applied to understand better the behavior of ⁷Be-aerosols in the surface atmosphere. This study shows that there is an inverse relationship among ⁷Be measured in the near ground air and solar activity. The modulation of ⁷Be-aerosols during the cycle 23 was divided in two steps. In the first stage, ascending phase, 1996–2002, the solar activity played an important role in the production rate of ⁷Be, r = ?0.75. However, during the descending phase, 2002–2009, the role of the solar activity was secondary, r = ?0.30, allowing that ⁷Be-aerosols reached the maximum concentration, 9.33 mBq m^?3 in August-09 when the solar activity was zero. Moreover, the remaining solar activity after the end of the ascending phase and the last important solar storm (December-06) caused the slowdown of ⁷Be production rate from 2001 to 2004 and the rupture of the seasonal behavior of ⁷Be in 2007, respectively. Finally, this research highlight the necessity to take into account the solar cycle phase, ascending or descending, to model studies of atmospheric process with ⁷Be as tracer since the contribution of the variables studied are so different in these stages.     

Surface Performance and Cytocompatibility Evaluation of Acrylic Acid-Mediated Carboxymethyl Chitosan Coating on Poly(tetrafluoroethylene-co-hexafluoropropylene)

To improve the biocompatibility of poly(tetrafluoroethylene-co-hexafluoropropylene) (FEP) film, a technique based on Ar plasma pretreatment and UV-induced grafting polymerization was used to immobilize carboxymethyl chitosan (CMCS) on the FEP film surfaces. Initially Ar plasma was used to treat FEP film. Then, plasma treated FEP film was modified via UV-induced grafting polymerization with hydrophilic acrylic acid (AAc) monomer. The following immobilization of CMCS on the FEP-pAAc surface was carried out via an amidation reaction. The change of chemical composition and surface morphology of FEP film were characterized by attenuated total reflectance Fourier transform infrared (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), scanning electronic microscopy (SEM) and atomic force microscopy (AFM). Results of water contact angles measurement showed that the hydrophilicity of the surface has improved significantly after surface modification. Furthermore, methyl thiazolyl tetrazolium (MTT) assay and cell morphology analysis confirmed that mouse fibroblasts (L929 cells) attachment and proliferation were improved remarkably on the modified FEP surface. These results suggest that CMCS were successfully employed to surface engineering FEP film, and enhanced its cell biocompatibility. The approach presented here may be exploited for surface modification of biomaterials.     

Investigation of the reaction mechanism and kinetics of production of anhydrous sodium metaborate (NaBO2) by a solid-state reaction

In this study, the solid-state reaction mechanism and kinetics were investigated for production of anhydrous sodium metaborate (NaBO₂), an industrially and technologically important boron compound. To assess the kinetics of solid-state production of NaBO₂, the chemical reaction between borax (Na₂B₄O₇) and sodium hydroxide (NaOH) was investigated by use of the thermal analysis techniques thermogravimetry (TG) and differential thermal analysis (DTA). DTA curves obtained under non-isothermal conditions at different heating rates (5, 10 and 20 °C/min), revealed five endothermic peaks corresponding to five solid-state reactions occurring at 70, 130, 295, 463, and 595 °C. The stages of the solid-state reaction used for production NaBO₂ were also analyzed by XRD, which showed that at 70 and 130 °C, Na₂B₄O₇ and NaOH particles contacted between the grains, and diffusion was initiated at the interface. However, there was not yet any observable formation of NaBO₂. Formation of NaBO₂ was initiated and sustained from 295 to 463 °C, and then completed at 595 °C; the product was anhydrous NaBO₂. Activation energies (E _a) of the solid-state reactions were calculated from the weight loss based on the Arrhenius model; it was found that in the initial stages of the solid-state reaction E _a values were lower than in the last three steps.     

Zethrene and Dibenzozethrene: Masked Biradical Molecules?

The syntheses, structures, and physical properties of dibenzozethrenes were explored. The results thus obtained were compared with those for zethrenes. Dibenzozethrenes were synthesized by the nickel‐catalyzed cyclodimerization of 9‐ethynyl‐1‐iodoanthracenes. The substituents in zethrene and dibenzozethrene twisted their backbones, and remarkably influenced their properties. Unlike closed‐shell disubstituted derivatives, the parent zethrene and dibenzozethrene are singlet open‐shell biradicals, which were studied by variable‐temperature ¹H NMR, ESR, SQUID and computational methods. Since substituents were observed to affect significantly the biradical properties, the relevant mechanisms were analyzed. The nonlinear optical performance of each of these compounds depends on its π‐conjugation and biradical properties. Dibenzozethrenes have larger two‐photon absorption cross‐sections than zethrenes, as most strongly evidenced by the parent dibenzothrene [σ_max=4323 GM at 530 nm].     

A new reflector structure for facility thermalizing D–T neutrons

A facility for thermalization of fast neutrons (14.2 MeV) emitted by compact deuterium–tritium (D–T) neutron generators (NGs) for thermal neutron activation analysis is proposed. Its final design is based on Monte Carlo calculations (MCNP5). To maximize the ratio between the thermal neutron flux and the total neutron flux and simultaneously to ensure the highest possible value of the thermal neutron flux at the output surface, the facility should consist of a two-layer reflector [tungsten (W)—the inner part, molybdenum—the outer part], a two-layer multiplier (W followed by lead), a moderator (polyethylene followed by magnesium fluoride) and a collimator (molybdenum and nickel near the output surface). For the D–T NG producing the maximum available neutron yield 10¹⁵ n s^?1, the facility provides the thermal neutron flux 2.0 × 10¹¹ n cm^?2 s ^?1 and a slightly higher fast neutron flux 2.3 × 10¹¹ n cm^?2 s^?1. To improve the ratio of the thermal neutron flux to the fast neutron flux (above 2.7) an addition of a silicon layer to the moderator and especially a proper adjustment and a threefold increase of the multiplier thickness is necessary.     

铁催化2-烯基氮杂芳烃的绿色合成

以廉价、低毒的醋酸亚铁为催化剂,在三氟乙酸助催化下,2-甲基氮杂芳烃与芳香醛经过加成与脱水反应,直接选择性合成具有生物活性的反式2-烯基氮杂芳烃化合物,水是唯一副产物.该合成方法催化剂用量少,后处理方便,产率高,选择性高,底物适用范围广.治疗哮喘药顺尔丁中间体(E)-3-[2-(7-氯-2-喹啉基)乙烯基]苯甲醛(3v)的克级合成展现了该方法的应用前景.     

Asymmetrically tetra-substituted phthalocyanine derivatives: synthesis,photophysical and photochemical properties

Transition Metal Chemistry - The syntheses of highly soluble asymmetrically substituted metal free and zinc phthalocyanine derivatives bearing three 4-(4-(5-phenyl-1,3,4-oxadiazol-2-yl)phenoxy) and...     

Evaluation of the effect of silicon on the carbonization process of Colombian semi-anthracites

The environmental impacts associated with the exploitation and transformation of fossil resources aggravate the planet's situation in terms of climate change. Due to this, this paper studies an alternative use of mineral coal as a precursor to obtaining new materials with different properties to the starting coals. The thermal degradation of two Colombian semi-anthracites is analyzed through the thermogravimetry (TG) technique coupled to a Fourier transform infrared spectroscopy (FTIR) equipment from room temperature (25 °C) to 900 °C, at a heating rate of 10 K min^?1 in an inert atmosphere. The catalytic effect of the addition of silicon to these samples before being subjected to a carbonization process is evaluated during this process. The results indicated that the primary reaction occurs in the temperature range between 400 and 680 °C, where the highest mass loss rate was observed. At the end of the heating process, the TG profile of the samples with silicon addition showed losses between 14.33 and 18.82% in mass, these values being slightly higher compared to the starting and demineralized samples. The release of water, light gases such as CO₂, CH₄, and species such as toluene, phenol and formic acid was identified in most of the samples. The presence of silica seems to favor the release of all these species, being more evident in one of the semi-anthracites studied. According to the results obtained, it is proved that the presence of silicon in samples subjected to carbonization processes has a catalytic effect that improves some characteristics of the new materials obtained, thus contributing to the use of carbon to get new materials.