基于CAN总线的遥测数据处理模块软件设计

随着飞行器电子综合化技术的发展,数据总线在飞行器中得到大量应用。为满足某飞行器总线系统测量的需求,本文设计了一种基于CAN总线的遥测数据处理模块。硬件部分主要由CAN总线驱动器模块、DSP数字信号处理模块、FPGA逻辑处理模块组成。软件设计包括TMS320F28335的初始化,CAN总线数据处理和外部中断处理三部分。该模块用于某飞行器双路CAN总线数据的采集及处理,并经过了多次飞行试验验证。该模块简化了系统设计,实现了高速、可靠的CAN总线遥测数据处理。     

一种宽能谱多球中子谱仪能量响应的MC模拟

利用蒙特卡罗程序FLUKA模拟计算了聚乙烯慢化球和辅助材料慢化球对低能中子到高能中子的响应函数曲线。结果表明,对纯聚乙烯球来说,随着聚乙烯层厚度的增加,响应曲线峰逐步右移,峰值在高能区有所下降,对20 Me V以上的中子,无论纯聚乙烯球的尺寸有多大,其响应均下降到很低的程度;对辅助材料慢化球来说,中子能量小于1 Me V时,辅助材料慢化球与聚乙烯慢化球的响应曲线相似,但当中子能量大于20 Me V时,中子与辅助材料层发生(n,xn)反应,慢化球的响应呈显著上升趋势。分析计算结果,最终能够确定宽能谱多球中子谱仪的尺寸组合。     

乙酰丙酮氧钼催化的苯乙烯双羟化反应

以钼酸铵与乙酰丙酮反应生成催化剂乙酰丙酮氧钼MoO2(acac)2,考察了反应溶剂、氧化剂存在形式、不同助催化剂、反应温度、底物配比和催化剂量对苯乙烯双羟化反应的影响。在优化的反应条件下,以过氧叔丁醇为氧化剂得到苯乙烯双羟化反应的转化率、化学选择性和分离产率分别为85.2%、70.7%和53.3%。并探讨了可能的催化机理以及改进方向。     

极谱法测定矿石及冶金渣中铍含量

矿石及冶金渣试样与过氧化钠在700℃熔融,用温水浸取,以一定量盐酸酸化后定容。分取部分试样溶液使其中铍(Ⅱ)与铍试剂Ⅲ在EDTA、氯化铵和氨水底液中,生成稳定的配合物,该配合物于-0.80V(vs.SCE)处产生一灵敏的吸附波,其峰电流的二阶导数与铍(Ⅱ)的质量浓度在0.004~0.20mg·L-1范围内呈线性关系,检出限(3S/N)为0.3μg·L-1。方法用于了7个矿石及冶金渣样品的分析,所得测定值与认定值一致。方法的加标回收率在96.0%~105%之间,相对标准偏差(n=6)在1.3%~9.7%之间。     

基于三唑配体的金属锰(Ⅱ)、锌(Ⅱ)配合物的合成、晶体结构与性质研究(英文)

在不同反应条件下,采用三唑衍生物作为配体与乙酸锰和硝酸锌反应,合成了2个具有三维结构的配位化合物{Mn(pytyba)(H2O)3]·2H2O}n(1)和{[Zn(pytyba)(H2O)3]·4H2O}n(2),并通过元素分析、热重分析、荧光性、X射线单晶衍射对化合物进行分析。结构分析表明1和2有许多共同特征:两个聚合物的晶体均属于单斜晶系,C2/c空间群,Mn2+和Zn2+均为六配位畸变八面体配位结构,具有相似的热稳定性、荧光性以及相近的孔隙率。配体中的氧原子与金属离子配位形成一维链状结构,然后又通过O-H…N、O-H…O氢键作用和π…π芳香堆积形成超分子结构。此外,通过测定化合物抗氧化活性(SOD)的经典方法-Marklund法对配合物1和2的抗氧化活性进行了研究。     

5-异烟酰胺异钛酸构筑的Cu(Ⅰ)-Eu和Ni(Ⅱ)-Eu化合物的合成、晶体结构和性质研究(英文)

利用不同过渡金属盐在溶剂热中合成了2个杂核化合物{[CuEu2(INAIP)3(HCOO)(H2O)3]·3H2O}n(1)和{[NiEu2(INAIP)4(H2O)4]·4H2O}n(2)(INAIP=异烟酰胺吡啶基异酞酸根),并对其进行了元素分析、IR及X-射线衍射法表征。晶体结构研究表明:配合物1和2都属于三斜晶系,P1空间群。晶胞参数:配合物1 a=1.088 7(3)nm,b=1.515 8(4)nm,c=1.564 4(2)nm,V=2.333 2(10)nm3,Z=2,Dc=1.955 g·cm-3,μ=3.203 mm-1,F(000)=1352,Rint=0.027,R1=0.0505,wR2=0.1309。配合物2 a=1.013 4(3)nm,b=1.083 6(6)nm,c=1.374 1(2)nm,V=1.453 0(9)nm3,Z=1,Dc=1.878 g·cm-3,μ=2.554 mm-1,F(000)=818,Rint=0.045 8,R1=0.034 1,wR2=0.086 9。配合物1是由配体异烟酰胺吡啶基异酞酸连接而成的三维二重贯穿sqc27拓扑结构,而配合物2是由配体异烟酰胺吡啶基异酞酸连接稀土铕离子形成二维层状结构,该二维层通过Ni-O和Ni-N键连接成三维非贯穿网络结构。配合物1和2具有典型的稀土铕离子红色荧光和高的热稳定性。     

基于反应性两嵌段共聚物的刺激响应性有机/无机杂化囊泡的制备及性能研究

采用ATRP法制备了结构明确的两亲性嵌段共聚物聚[甲基丙烯酸(N,N-二甲氨基)乙酯-b-甲基丙烯酸(3-(三甲氧基硅基))丙酯],其在甲醇/水的混合溶液中自组装形成囊泡结构,并通过甲基丙烯酸[3-(三甲氧基硅基)]丙酯链段中三甲氧基硅基的水解交联,形成了稳定的共聚物囊泡结构。用光散射、SEM和TEM对囊泡的结构进行了表征。所得共聚物囊泡粒子具有温度和pH双重响应性,通过简单调控温度或pH值来实现囊泡粒子的溶解与沉淀收集,可用于蛋白质等的分离与纯化。     

中温热解焦油重馏分悬浮床加氢裂化的研究

以中温热解煤焦油为原料,对其性质进行了分析,其中,350℃重质馏分中胶质含量30.88%,沥青质含量37.27%,四氢呋喃不溶物3.36%,属于常规固定床加氢裂化难以直接处理的馏分。合成了一种Mo系超分散催化剂,采用FT-IR、XPS、XRD、SEM和TEM等对催化剂进行了表征,催化剂中含有Mo=O和Mo-S特征结构,活性金属的硫化率为84.34%,在体系中具有优良的分散性,在反应体系内原位分解为超分散MoS_2颗粒;在0.25 t/d连续装置上进行了热解重油悬浮床加氢裂化实验研究,考察了反应条件对产物分布情况和结焦率的影响,得出适宜的反应条件为19 MPa,440℃,催化剂的添加量为300 mg/kg;此条件下石脑油收率24.47%,柴油馏分收率49.71%,结焦率1.32%。     

不可燃氟代碳酸酯基钠离子电池电解液

Lithium-ion batteries (LIBs) are widely used in cellphones, laptops, and electric cars owing to their high energy density and long operational lifetime. However, their further deployment in large-scale energy storage systems is restricted by the uneven distribution of lithium resources (~0.0017% (mass fraction, w) in the Earth's crust). Therefore, alternative energy storage systems composed of abundant elements are of urgent need. Recently, sodium-ion batteries (SIBs) have attracted significant attention and are considered to be a potential alternative for next-generation batteries owing to abundant sodium resources (~2.64% (w) of the Earth's crust), suitable potential (−2.71 V), and low cost. SIBs are similar to LIBs in terms of their physical and electrochemical properties. Previous studies have mainly focused on SIB storage materials, including hard carbon, alloys, and hexacyanoferrate, while the safety of SIBs remains largely unexplored. Similar to LIBs, the current electrolytes used in SIBs are mainly composed of flammable organic carbonate solvents (or ether solvents), sodium salts, and functional additives, which pose possible safety issues. Moreover, the chemical activity of sodium is much higher than that of lithium, leading to a higher risk of fire, thermal runaway, and explosion. To overcome this problem, herein we propose a fluorinated non-flammable electrolyte composed of 0.9 mol∙L⁻¹ NaPF₆ (sodium hexafluorophosphate) in an intermixture of di-(2, 2, 2 trifluoroethyl) carbonate (TFEC) and fluoroethylene carbonate (FEC) in a 7 : 3 ratio by volume. Its physical and electrochemical properties were studied by ionic conductivity, direct ignition, cyclic voltammetry, and charge/discharge measurements, demonstrating excellent flame-retarding ability and outstanding compatibility with sodium electrodes. The electrochemical tests showed that the Prussian blue cathode retained a capacity of 84 mAh∙g⁻¹ over 50 cycles in the prepared electrolyte, in contrast to the rapid capacity degradation in a flammable conventional carbonate electrolyte (74 mAh∙g⁻¹ with 57% capacity retention after 50 cycles). To test the practical application of the proposed electrolyte, a hard carbon anode was used and exhibited exceptional performance in this system. The enhancement mechanism was further verified by Fourier transform infrared (FTIR), X-ray diffraction (XRD), and scanning emission microscopy (SEM) investigations. Polycarbonate on the surface of the cathode played an important role for the studied electrolyte system. The polycarbonate may originate from FEC decomposition, which can enhance the ionic conductivity of the solid electrolyte interface (SEI) layer and reduce impedance. Hence, we believe that this proposed electrolyte may provide new opportunities for the design of robust and safe SIBs for next-generation applications.     

Synthesis,Characterization and Catalytic Activity of Salen Co(Ⅲ)Cl in Alternating Copolymerization of CO2 and Propylene Oxide

The title complex Salen Co(Ⅲ)Cl(Salen = 6,6’-((1E,1’E)-(cyclohexane-1,2-diylbis(azaneylylidene))bis(methaneylylidene))bis(2,4-di-tert-butylphenol)) was synthesized and characterized by elemental analysis, IR spectroscopy, 1H NMR and UV-Vis. The complex can be used as catalyst for the propylene oxide(PO)/CO2 copolymerization in different conditions of reaction time, reaction temperature, carbon dioxide pressure and monomer concentration, and the optimum conditions for copolymerization were obtained.