低渗温热腹腔灌注化疗治疗恶性腹腔积液的临床研究

目的 评价低渗温热腹腔灌注化疗治疗恶性腹腔积液的疗效及不良反应。方法 行腹腔穿刺置单腔中心静脉导管,外接引流袋,记录腹水引流量,当日排放腹水1 500ml 后,予加热至43~45℃注射用双蒸馏水1 000ml 行腹腔灌注,次日重复放液1 500ml,再予加热至43~45℃注射用双蒸馏水1 000ml 行腹腔灌注,并于灌注后腹腔注入顺铂60mg、氟尿嘧啶500mg 并封管,治疗期间常规给予简单水化、对症止吐等治疗。结果 31 例恶性腹腔积液患者共完成低渗温热腹腔灌注化疗42 周期,完全缓解7例,部分缓解15,稳定5 例,进展4 例,完全缓解+ 部分缓解占70.97%。中位进展时间（TTP）3.6个月（2～9 个月）, 中位生存期（MST）5.6 个月。毒副反应以消化道反应为主。结论 低渗温热腹腔灌注化疗治疗恶性腹腔积,在延长患者的生存期、提高生活质量方面效果较好,临床上可推荐应用。     

Improvement of resistive switching fluctuations by using one step lift‐off process

Bipolar resistive switching characteristics are investigated in ZrO₂ containing Cu thin layer devices, particularly for the self‐isolated‐structure device fabricated by one step lift‐off process. Compared with the traditional‐structure device, the self‐isolated‐structure device shows more uniform resistive switching characteristics. This is because the isolation of each device cell has negligible influence on each other and thus mitigates possible crosstalk between each cell. These results suggest that the feasibility of good stabilization of the resistive switching parameters can be obtained through one step lift‐off process. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Spin gapless semiconductor like Ti2MnAl film as a new candidate for spintronics application

A novel Heusler ferrimagnet Ti₂MnAl film has been grown on Si(001) substrate using magnetron sputtering. Characteristics of its magnetic and transport properties reveal the spin‐gapless‐semiconductor (SGS) nature of the stoichiometric Ti₂MnAl, in agreement with theoretical prediction. The as‐grown SGS‐like Ti₂MnAl film demonstrated high Curie temperature, nearly compensated ferrimagnetic properties with small coercivity and low magnetization. It also showed semiconductor‐like behavior at room temperature allowing good compatibility with commercial Si‐based semiconductor. In this regards, Ti₂MnAl film is a potential candidate material for spintronics application, especially for the minimization of energy consumption of device. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

导弹发射姿态测量方法研究

针对导弹发射姿态测量问题,提出采用高速摄像机通过斜瞄和平瞄姿态测量方法求解导弹中轴线俯仰角和方位角,仿真典型导弹起飞段近距离姿态测量,分析两种测量方法对导弹飞行姿态测量精度和适用性。仿真结果表明:平瞄和斜瞄姿态测量方法,测量误差在0.2°以内。斜瞄方式使用更便捷,通用性好。平瞄方式测量精度高,数据处理方法、机械结构相对简单,在适合的应用场合优势明显。此分析方法、分析结果为姿态测量方法选取和研究等提供一种可行的途径,也可为其它运动目标的姿态测量提供借鉴。     

Distributed Bragg reflector laser(1.8 μm) with 10 nm wavelength tuning range

We report a 1.8 μm two-section distributed Bragg reflector laser using butt-jointed In Ga As P bulk material as the waveguide core layer. The threshold current is 17 m A and the output power is 8 m W on average. The threshold current, output power, and emitting wavelength dependences on temperature are measured. The obtained wavelength tuning range is 10 nm. This device has potential applications in simultaneous multiple-gas detection.     

Electrochemical performance of lithium ion capacitors with different types of negative electrodes

The electrochemical properties of various commercial carbon materials (activated carbon (AC), graphite (GP) and hard carbon (HC)) have been investigated for use as negative electrode for lithium ion capacitors. The rate capabilities and cycle durabilities are tested up to 20 C and 1000 cycles using full cell configurations. It is found that the lithium ion could not efficiently intercalate into the activated carbon materials. The symmetrical AC/AC capacitor shows good cycle durabilities at 10 C with capacity of 17 mA h g^?1. The asymmetrical capacitors AC/GP and AC/HC with intercalated negative electrodes show higher capacities than that of AC/AC capacitor. Moreover, the AC/HC has better rate capabilities than AC/GP.     

Ordered Mesoporous Carbon and Thiolated Polyaniline Modified Electrode for Simultaneous Determination of Cadmium(II) and Lead(II) by Anodic Stripping Voltammetry

The fabrication and evaluation of a glassy carbon electrode (GCE) modified with ordered mesoporous carbon (OMC), 2‐mercaptoethanesulfonate (MES)‐tethered polyaniline (PANI) and bismuth for simultaneous determination of trace Cd²⁺ and Pb²⁺ by differential pulse anodic stripping voltammetry (DPASV) are presented here. The morphology and electrochemical properties of the fabricated electrode were respectively characterized by scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). Experimental parameters such as PANI disposition, preconcentration potential, preconcentration time and bismuth concentration were optimized. Under optimum conditions, the fabricated electrode exhibited linear calibration curves ranged from 1 to 120 nM for Cd²⁺ and Pb²⁺. The limits of detection (LOD) were 0.26 nM for Cd²⁺ and 0.16 nM for Pb²⁺ (S/N=3), respectively. Additionally, repeatability, reproducibility, interference and application were also investigated, and the proposed electrode exhibited excellent performance. The proposed method could be extended for the development of other new sensors for heavy metal determination.     

Electrochemical performance of pre-lithiated graphite as negative electrode in lithium-ion capacitors

Electrochemical performance of the pre-lithiated graphite and the as-assembled lithium-ion capacitors (LICs) were investigated within the Li/graphite two-electrode cell and activated carbon (AC)/graphite two-electrode cell, respectively. The morphologies of the electrodes were characterized by scanning electron microscopy (SEM). The Li intercalation of Li/graphite two-electrode cell was performed using short circuiting and galvanostatic charging techniques. The Li pre-doping process was characterized by electrochemical impedance spectroscopy (EIS). The cycle performance of the LICs were investigated at the rates of 1–20 C between the cut-off voltage at 2 to 4 V. The results demonstrated that the LIC cells with 8 h pre-doping time have the best cycle performance at the high rate of 10 C. Li pre-doping methodology plays a crucial role in the electrochemical performance of the graphite electrode and the as-assembled LICs.     

常用玻璃量器检定注意事项

总结了常用玻璃量器检定过程中的注意事项,讨论了外观检查、清洁度、涂抹油脂、温度控制、液面观察方法对常用玻璃量器检定结果的影响,其中定容时是否使用黑色遮光带造成的影响最大。     

Poly(phenylene oxide) modified cyanate resin for self‐healing

Self‐healing cyanate ester resins (CE) were developed by adding low molecular weight poly(phenylene oxide) (PPO) resin, yielding a high performance CE/PPO system via a low‐temperature process. The addition of PPO improved the flexural strength and fracture toughness of the CE matrix without sacrificing thermal properties. CE/PPO formulations with 5, 10, and 15 wt.% PPO showed 43%, 65%, and 105% increase in fracture toughness due to a combination of crack deflection, crack pinning, and matrix cavitation around second‐phase particles. When PPO was introduced into the CE, dielectric properties were either unchanged or declined. During thermal treatment to heal damaged CE, liquid PPO flowed into cracks, and during subsequent cooling, solidified to bond the crack surfaces. The self‐healing efficiency for CE with 15 wt.% PPO after heating to 220°C for 1 h exhibited a recovery of 73% in toughness and 81% in microtensile strength. Copyright © 2014 John Wiley & Sons, Ltd.