傅里叶变换轮廓术中新的相位及高度算法分析

在传统傅里叶变换轮廓术三维面型测量中,为了准确得到被测物体的高度分布,必需保证投影仪出射光瞳和摄像机入射光瞳的连线与参考面平行并且在同一水平面,否则存在较大的误差。着眼于更普通的情况,讨论双瞳连线与参考面成某一夹角时的高度计算,推导出了非平行时的参考面光场及物面变形条纹光场的表达式,并给出了高度映射公式。因而,传统的傅里叶变换轮廓术测量成为角度α=0时的特例。该方法使傅里叶变换轮廓术的测量条件得到了放宽;易于通过移动投影装置或成像装置获取全场条纹;并为在难以实现双瞳与参考面平行的特殊环境下的测量提供了可行的方法。计算机模拟及实验均证实了该方法的有效性。     

Highly stable and efficient KTP-based intracavity optical parametric oscillator with a diode-pumped passively Q-switched laser

We present in this paper a highly stable and efficient KTP-based intracavity optical parametric oscillator with a diode-end-pumped Nd:YVO₄/Cr:YAG passively Q-switched laser. At the incident diode pump power of 4 W, the signal (1.57 μm) and idler (3.29 μm) average output powers up to 580 and 100 mW, respectively, have been achieved. The corresponding conversion efficiency from the input diode pump power to the output signal power is 14.5%, while that to the total OPO output (signal+idler) reaches 17%. To the best of our knowledge, these are the highest conversion efficiencies reported to date. After more than four hours of investigation, the OPO power stability better than 2% has been obtained. In addition, efficient cavity dumping of the IOPO has inevitably led to the short pulse duration (1.6 ns) and high peak power output (8.3 kW) at the signal wave. Additionally, the amplitude and repetition rate fluctuations of the signal pulses are well within 5%. PACS 42.55.Xi; 42.60.Gd; 42.60.Lh; 42.65.Yj     

小波变换轮廓术的测量范围研究

利用小波“脊”处的小波系数来提取变形条纹中的相位信息可以在很大程度上抑制条纹图中有用的基频分量与零频和其它谐波频率分量的混叠,弥补了傅里叶变换轮廓术的不足。从离散信号频域分析角度,推导了变形条纹小波变换的频谱描述形式,讨论了其测量范围,包括结构条件和抽样条件。结果表明,只有在无周期内瞬时频谱混叠,即任意位置处物体瞬时高度变化满足h/xx=b<1/3条件时,和不存在抽样引起的周期间瞬时频谱混叠的抽样条件下(即一个周期内的抽样点数m≥4时),小波变换轮廓术才能正确恢复被测物体的三维面型。计算机模拟和实验验证了该结论。     

Strength characteristics of the self-sustained wave in grooved channels with different groove length

The self-sustained oscillations arising in a series of grooved channels are investigated experimentally. Pressure drop, time-averaged and time-various local pressure in the grooved channels with six kinds of groove length are measured with the differential transducer and the pressure sensor, respectively, and the flow structures are visualized using the aluminum dust method. The local pressure signal shows that the self-sustained wave appears in the first or second frequency, and the Strouhal number, based on the nature frequency of the self-sustained wave, is almost equivalent for the first or second frequency in the same channel. Meanwhile, the Strouhal number for each channel decreases monotonously with the groove length. Furthermore, it is found that increasing pressure will result in higher amplitude of the self-sustained wave, this behavior is significant for the efficient heat transfer in practical engineering.     

利用原子层外延方法制备的ZnS:Er3+薄膜的交流电致发光特性

采用原子层外延方法(ALE)制备了ZnS:Er3+交流电致发光(ACEL)薄膜,得到了明亮的绿色EL。发现了随Er3+离子浓度增加,对应于4F9/2→4I15/2跃迁的谱线强度增加甚至超过2H11/2→4I15/2跃迁的谱线强度。通过对EL衰减的分析,发现了绿红比随外加电压的变化关系以及EL光谱与温度的关系。在Er3+离子浓度较高时,Er3+离子之间发生明显的能量传递。提出了Er3+离子间的交叉驰豫模型并计算了交叉弛豫速率,同拟合衰减曲线得到的值相比,两者符合得较好。     

Investigation of the thickness of Ag, AgI films in the capillary for hollow waveguides

A metallic (Ag)–dielectric (AgI) hollow glass waveguide is a promising and flexible fiber for the delivery of high-power CO₂ laser radiation. The thickness of metallic (Ag) films and dielectric (AgI) films is a critical factor which greatly influences the attenuation of the waveguides. In this paper, metallic (Ag)–dielectric (AgI) films were successfully prepared in the capillary whose inner diameter is 0.53 mm, and firstly investigated with theoretical analysis and measured by means of AES and SEM. There is good agreement between theoretical thickness and experimental results, which confirms the validity of the theoretical analysis, which makes the estimate of the thickness of both the metallic and dielectric films possible with high accuracy prior to the preparation of hollow glass waveguides. The attenuation spectra of Ag/AgI hollow waveguides shows the loss increases with the thickness of Ag, AgI films and indicates that the Ag/AgI hollow waveguide is suitable for the transmission of IR radiation.     

Influence of Solvent Polarity and Hydrogen Bonding on the Electronic Transition of Coumarin 120: A TDDFT Study

The characteristics of the electronic transition energy of Coumarin 120 (C120) and its H‐bonded complexes in various solvents have been examined by time‐dependent density functional theory (TDDFT) in combination with a polarizable continuum solvent model (PCM). Molecular structures of C120 and its H‐bonded complexes are optimized with the B3LYP method in PCM solution, and the dihedral angle H14? N13? C7? H15 is dependent on solvent polarity and the type of H‐bond. A linear correlation of the absorption maximum of C120 with the solvent polarity function is revealed with the PCM model for all solvents except DMSO. The experimental absorption maximum of C120 in nine solvents is well described by a PCM–TDDFT scheme augmented with explicit inclusion of a few H‐bonded solvent molecules, and quantitative agreement between our calculated results and experimental measurements is obtained with an average error of less than 2 nm. H‐bonding at three different sites shifts the absorption wavelength of C120 either to the blue or to the red, that is, a significant role is played by solvent molecules in the first solvation shell in determining the electronic transition energy of C120. The dependence on the H‐bonding site and solvent polarity is examined by using the Kamlet–Taft equation for solvatochromism.     

基于最新势能面的C(1D)+H2反应的环聚合分子动力学研究

本文利用环聚合分子动力学方法对C(¹D)+H₂反应开展了详细的理论研究. 计算中使用了最近构建的Zhang-Ma-Bian(ZMB)从头算势能面,该势能面对锥形交叉附近区域以及范德华区域均有精确的描述. 环聚合分子动力学计算得到的热反应速率常数与最新实验值吻合很好. 与前人计算结果比较,发现在?¹A′电子基态的ZMB-a势能面上获得的反应速率常数远大于前人构建的RKHS势能面上的结果,这是由于ZMB势能面上的范德华鞍具有与之前势能面上的范德华阱完全不同的动态学作用,表明环聚合分子动力学方法能够处理范德华作用引起的势能面拓扑结构所导致的动态学效应. 本文还揭示了b¹A′′电子激发态ZMB-b势能面以及量子效应对反应的重要性.     

基于改进U-Net的量子点STM图像分割

为提升量子点图像分割精度,降低特征识别误差,提出一种基于改进U-Net的量子点图像分割方法.首先,在预处理阶段,设计了以色彩通道为权值的灰度化算法,以提升后续分割效果.其次,在STM图像分割部分,在原始U-Net结构上引入中间过渡层以均衡网络各层特征.而后,建立数据集,并通过实验对比不同分割算法的精确度、召回率、F-measure.最后,将分割算法应用于量子点的特征识别,并测试了不同分割方式对应用的影响.实验结果显示,改进灰度化方法保留细节信息丰富,明显提升了量子点分割精度;改进U-Net的平均精确率、召回率、F-measure相较原始网络分别提升了13.83%、2.16%、8.13%.同时,实验数据表明由于分割精度的提升,量子点数量、纵横比等特征参数的识别更加精确.     

Progress in fluorene-based wide-bandgap steric semiconductors

Molecular bulks are favorable for the thermal and morphological stability in organic wide-bandgap semiconducting polymers with potential applications in both information and energy electronics. In this review, we present our progress in the design of fluorene-based bulky semiconductors with a fractal four-element pattern. Firstly, we established one-pot methods to spirofluorenes, especially spiro[fluorene-9,9′-xanthene](SFX) serving as the next-generation spiro-based semiconductors. Secondly, we observed the supramolecular forces at the bulky groups and discovered the supramolecular steric hindrance(SSH) effect on polymorphisms, nanocrystals as well as device performance. Thus, a synergistically molecular attractor-repulsor theory(SMART) was proposed for the control of nanocrystal morphology, thin film phase and morphology. Thirdly, the third possible type of defects has been identified to generate green band(g-band) emission in widebandgap semiconductors by the introduction of molecular strain design of cyclofluorene. Finally, the first bulky polydiarylfluorene with highly crystalline and β conformation was achieved by an attractor-repulsor design of tadpole-shape monomer, which offered an effective platform to fabricate stable wide-bandgap semiconducting devices. All the discoveries offer the solid basis to break through bottlenecks of organic/polymer wide-bandgap semiconductors by the improvements of overall performances.