免疫磁性纳米微球的制备与表征

成功制备了Fe3O4磁性纳米颗粒及二甲基丙烯酸乙二醇酯-甲基丙烯酸(EGDMA-MAA)共聚物包覆的Fe3O4磁性复合微球。将吲哚美辛抗体固定在复合微球表面,形成了Fe3O4(核)/聚合物-抗体(壳)的复合免疫磁性颗粒。XRD结果表明,制备的Fe3O4的晶型为反立方尖晶石型且纯度较高;TEM表征表明Fe3O4粒径较为均匀,平均粒径为12nm;磁性复合微球的平均直径为460nm。制备的Fe3O4磁性纳米颗粒和磁性复合微球有较强的磁响应强度,其饱和磁化率分别为49.16和8.38emu/g,能够满足磁性分离的要求。FT IR验证了磁性复合微球中羧基特征峰的存在,表明羧基成功连接在磁性微球上面。通过碳二亚胺/N-羟基琥珀酰亚胺(EDC/NHS)活化法将微球表面羧基活化并成功与抗吲哚美辛抗体交联。     

相转移法制备Fe3O4正己烷磁流体

采用一种新的相转移法制备了双层包裹的Fe3O4正己烷磁流体.首先,以油酸钠作为表面改性剂,对化学共沉淀制备的Fe3O4纳米颗粒进行双层包裹,制备了稳定的水基磁流体,在此基础上,通过加入乙酸(CH3COOH)将亲水颗粒转变为亲油颗粒,并用萃取的方法将亲油颗粒成功转移到正己烷相.傅里叶变换红外光谱(FTIR)表明,通过调整pH值可以将双层包裹的磁性颗粒外层带有的亲水基团油酸根R—COO-转变为亲油的R—COOH,从而使得包裹的颗粒既可溶于极性载液也可溶于非极性载液.利用X射线衍射仪(XRD)、振动样品强磁计(VSM)和透射电子显微镜(TEM)对Fe3O4颗粒的形貌、组成及磁流体的性质进行了表征.结果表明,利用这种新的相转移法可以保证颗粒在单分散下充分包裹并避免团聚.制备的正己烷磁流体稳定性好,长期放置未发生分层现象.通过蒸发正己烷,可以得到不同固含量的磁流体并可以将其与其它油基载液互溶,从而得到不同载液的Fe3O4油基磁流体.     

介孔SiO_2/Fe_3O_4中空磁性复合微球的制备与表征

采用多步包覆法在自制的240nm的单分散SiO2微球表面进行β-FeOOH的包覆,在5wt%的NaOH溶液中去除核心SiO2后,得到β-FeOOH纳米结构空心微球。将单分散的β-FeOOH空心球作为内核,十六烷基三甲基溴化铵(CTAB)为模板剂,正硅酸乙酯(TEOS)为硅源,经水解缩聚反应得到空心核壳复合微球。在空气中焙烧(500℃,5h)对样品去除模板剂,并在还原气氛(5%H2/95%Ar,350℃,3h)下焙烧得到介孔SiO2/Fe3O4中空磁性复合微球。结果表明,所制得的介孔SiO2/Fe3O4中空磁性复合微球中的Fe3O4层厚度约60nm,是由Fe3O4纳米棒搭接而成的三维网络结构,复合微球的整体平均直径为390nm,比表面积较高约693m2·g-1,孔体积为0.63cm3·g-1,平均孔径为3.6nm,其饱和磁化强度可达13.6emu·g-1,同时较低的矫顽力(50Oe)有利于颗粒的再分散。     

亚微米级Cu0/Fe3O4复合物多相催化过一硫酸盐降解有机污染物

过一硫酸盐催化活化技术因其可产生强氧化性活性氧化物种,可快速氧化降解并矿化有机污染物的优异性能而备受关注.本文成功制备了亚微米级Cu0/Fe3O4复合物,发现其能多相催化过一硫酸盐产生单线态氧降解有机污染物.首先,以CuCl2·2H2O,FeCl2·4H2O和FeCl3·6H2O为铜源和铁源,水合肼为还原剂,采用水热法在180oC反应24 h制备了亚微米级磁性Cu0/Fe3O4复合物.表征结果显示,所制材料为Cu0和Fe3O4的复合物,颗粒大小约为220 nm;单一相Cu0和Fe3O4晶体粒径分别为33.8和106.2 nm,而Cu0/Fe3O4复合物中Cu0和Fe3O4晶体粒径分别减为20.8和31.9 nm.这表明Cu0和Fe3O4复合降低了Cu0和Fe3O4晶体粒径,有利于Cu0和Fe3O4的分散.BET测试结果表明,Cu0/Fe3O4复合物比表面积为4.6 m2/g,与Cu0颗粒的(4.2 m2/g)相当,但远小于Fe3O4的(15.6 m2/g).制备的Cu0/Fe3O4复合物可有效催化过一硫酸盐产生单线态氧降解罗丹明B、亚甲基蓝、金橙II、苯酚和对氯酚.当Cu0/Fe3O4复合物的用量为0.1 g/L,过一硫酸盐浓度为0.5 mmol/L和初始pH为7时,Cu0/Fe3O4复合物可在30 min内完全降解20μmol/L的罗丹明B、亚甲基蓝、金橙II以及0.1 mmol/L的苯酚和对氯酚.对比试验显示,在相同条件下,Cu0和Fe3O4颗粒分别可以降解28%和20%的罗丹明B.这表明Cu0/Fe3O4复合物中的Cu0和Fe3O4晶体在催化过一硫酸盐降解污染物的反应中具有协同作用,这主要来源于Cu0/Fe3O4复合物中Cu0和Fe3O4的晶体粒径变小和更好的分散.采用分光光度法测定了降解反应液中铜和铁离子的溶出量.当Cu0/Fe3O4复合物的用量为0.1 g/L,过一硫酸盐浓度为0.5 mmol/L和初始pH为7时,反应60 min后,降解液中铜和铁离子的浓度分别为0.22和0.1 mg/L,仅占复合物中总铜和总铁量的1.1%和0.2%,表明Cu0/Fe3O4复合物具有较强的化学稳定性.所制Cu0/Fe3O4复合物具有超顺磁性,借助磁场实现快速分离回收,可循环利用五次,表明其优越的催化稳定性.通过加入乙醇和叠氮化钠,考察了Cu0/Fe3O4复合物催化活化过一硫酸盐体系中的活性氧化物种.发现100 mmol/L乙醇的加入对污染物的降解无明显影响,而加入同等量的叠氮化钠可完全抑制污染物的降解,表明Cu0/Fe3O4复合物催化活化过一硫酸盐产生的主要活性氧物种为单线态氧.采用电子顺磁共振谱进一步证实了单线态氧的生成.基于以上研究,Cu0/Fe3O4复合物催化活化过一硫酸盐的机理为Cu0/Fe3O4作为一个电子媒介加速过一硫酸盐和污染物之间的电子转移,从而导致污染物被快速降解.该反应机理不同于常见的金属催化过一硫酸盐产生硫酸根和羟自由基的反应机理.我们推测,电导性优良的Cu0在此催化反应中起着关键性作用.本催化方法可作为一种绿色的氧化技术用于环境污染物的氧化降解处理.     

四氧化三铁磁性纳米微粒表面的氨基化修饰

以3-氨丙基三乙氧基硅烷(APTES)作为氨基化试剂,通过硅烷化反应使其键合于Fe3O4纳米颗粒表面,制备了表面氨基化的磁性Fe3O4纳米复合颗粒;利用红外光谱分析了产物的化学键合特征,利用电位滴定测定了合成产物表面的-NH2含量,探讨了活化方式、反应溶剂、投料比、温度、时间等因素对氨基化修饰效果的影响.结果表明,APTES成功地包覆在磁性Fe3O4纳米微粒表面;在乙醇-水体系中,在Fe3O4与APTES投料比3∶8、温度60℃下反应12h,得到的Fe3O4纳米颗粒表面APTES修饰效果最佳,表面-NH2含量高达1 400±50μmol·g-1.     

1,1-二苯基乙烯存在下无皂乳液聚合制备磁性复合微球

报道了一种制备磁性复合微球的方法——DPE法.在自由基控制剂1,1-二苯基乙烯(DPE)存在条件下,甲基丙烯酸甲酯(MMA)与丙烯酸(AA)发生无皂乳液聚合,制备能与Fe3O4粒子相螯合的活性短链共聚物,加入Fe3O4粒子把短链共聚物引到其表面,引发其它单体继续在Fe3O4粒子表面聚合,制备磁性复合微球.研究了AA、DPE、引发剂及Fe3O4粒子加入量等对制备磁性复合微球的影响.并在此基础上,对优化后工艺制备的磁性复合微球进行了TEM、TGA及磁响应性表征.结果表明,利用该新的方法制备出了磁含量为20%、比饱和磁化强度为32.2emu/g、平均粒径为265nm且表面不含任何杂质的磁性复合微球.     

水基溶胶-凝胶法制备稀土/碱土金属硅酸盐纳米粉

采用水基溶胶凝胶法,以廉价的无机盐Y2O3,MgO为前驱物,Si(OC2H5)4为络合剂,PEG4000为复合表面活性剂,氨水调节pH值,并利用无水乙醇超声分散技术,成功制备了分散性良好的稀土碱土金属复合硅酸盐纳米粉xY2O3·yMgO·zSiO2(YMS),考察了初始溶液的pH值、温度及浓度对溶液—溶胶—凝胶转变的影响,并利用TG DTA,XRD,TEM分析手段对复合硅酸盐纳米粉YMS的性质进行了研究。实验表明,在60℃相似文献   

纳米Fe3O4/聚苯乙烯均匀分散体系的制备及结构

用化学共沉淀法制备了Fe3O4纳米颗粒,以油酸为表面活性剂,苯乙烯为载液,制备了稳定的纳米Fe3O4可聚合磁流体,将可聚合磁流体经自由基引发聚合制成纳米Fe3O4/聚苯乙烯均匀分散体系,用WAXRD研究了Fe3O4纳米粒子的结晶情况;用FTIR研究了油酸表面改性前后Fe3O4粒子表面官能团的变化;用TEM研究了Fe3O4颗粒的粒径大小及其在苯乙烯单体和聚苯乙烯中的分散情况;用DSC和TGA研究了纳米Fe3O4/聚苯乙烯均匀分散体系的玻璃化转变温度(Tg)和热稳定性,结果表明,合成的纳米Fe3O4为立方晶型,平均粒径在10nm左右,油酸分子在Fe3O4表面是化学吸附,经表面处理的Fe3O4超细颗粒在苯乙烯和聚苯乙烯基体中分散较均匀.界面粘结较好,含1.8％Fe3O4纳米颗粒的聚苯乙烯的最大热失重温度比聚苯乙烯提高了13K,Fe3O4/聚苯乙烯复合体系的饱和磁化强度σs为17.43emu/g.     

新型磁性纳米金修饰过氧化氢生物传感器的研制

利用共沉淀法合成纳米Fe3O4颗粒,将半胱氨酸吸附到纳米Fe3O4微粒表面,借助半胱氨酸的巯基(-SH)对纳米金的强烈吸附,使纳米金自组装到磁性颗粒上,再通过静电吸附作用自组装辣根过氧化酶(HRP),合成了Fe3O4/Cys/Au/HRP纳米复合粒子,最后通过磁力将其修饰到固体石蜡碳糊电极表面,制得新型过氧化氢生物传感器.以对苯二酚作为电子媒介,用计时电流法对H2O2进行测定,线性范围为2.4 X10-3～6.0×10-6mol/L,检出限(S/N=3)为2.5 X 10-6mol/L,响应时间小于10 s.磁性纳米微粒Fe3O4/Cys/Au能够高效地保持HRP的生物活性.该新型传感器已用于实际样品测定.     

尺寸可控的聚苯胺复合微球的电纺制备与表征

以十二烷基苯磺酸(DBSA)掺杂的导电聚苯胺与聚乙二醇(PEG)及Fe3O4的混合氯仿溶液,采用静电纺丝(spinning technology)方法制备含Fe3O4纳米颗粒的导电聚苯胺(PANI)/PEG/Fe3O4复合微球.SEM结果表明,电纺所得的PANI/PEG/Fe3O4复合微球结构依赖于PEG聚合物浓度、静...     

有机磁合成化学研究进展

通过磁场对聚合反应、酯化反应、光还原反应和不对称合成等的影响，论述了有机磁化学的理论研究和应用进展。磁场在一定程度上影响有机反应的反应速率、产率、反应途径和产物构成。同时初步探讨了磁场影响化学反应速率的机理，并展望了磁化学的发展前景。     

Magnetic nano- and microparticles in biotechnology

Both synthetic and biologically produced magnetic nano- and microparticles exhibit several types of responses to external magnetic field which have been already employed in various areas of biosciences, biotechnology, medicine, environmental technology, etc. This short review shows selected important biotechnological applications of magnetic particles, and the biological processes leading to biogenic magnetic particles formation. Presented at the 1st Nanomaterials and Nanotechnology Meeting, Nano Ostrava, Ostrava, Czech Republic, 1–4 September 2008.     

Magnetic resonance in Cu(hfac)2LR heterospin chain polymer complexes

Cu(hfac)₂ chain polymer heterospin complexes with pyrazole-substituted nitronylnitroxides (L^R, where R = Me, Et) with a composition Cu(hfac)₂L^R, exhibiting structural rearrangements with magnetic effects in the solid state at reduced temperatures, were studied by magnetic resonance. The magnetic resonance spectrum changes substantially for substituents of different types. The results of this study are discussed in the context of the cluster approach in view of the specific crystal structure of the compounds.     

Physical Properties of Elongated Magnetic Particles: Magnetization and Friction Coefficient Anisotropies

Anisotropy counts: A brief review of the main physical properties of elongated magnetic particles (EMPs) is presented. The most important characteristic of an EMP is the additional contribution of shape anisotropy to the total anisotropy energy of the particle, when compared to spherical magnetic particles. The electron micrograph shows Ni‐ferrite microrods fabricated by the authors.

     

Floating Diamonds with Nanomagnetic Particles

In the diamond industry, ferrofluids are used in ferrohydrostatic separators for the density separation of diamonds from gangue material. The size of the magnetic core of the coated particles forming the ferrofluid suspension is vital in ensuring the stability of the fluid. The particle size must be small enough such that sedimentation does not occur in a magnetic field gradient and under the influence of a gravitational field and such that magnetic agglomeration can be overcome. This paper discusses the particle size requirements for fluid stability under the influence of these effects.     

A Novel Approach to Magnetic Nanoadsorbents with High Binding Capacity for Bovine Serum Albumin

Magnetic nanoadsorbents using Fe₃O₄ nanoparticles as cores and poly(methyl acrylic acid) (PMAA) as ionic exchange groups were prepared through our novel approach. Two steps were involved in this approach: the first was to functionalize the magnetic nanoparticles (MNPs) with methacrylate double bonds via the combination of ligand exchange and condensation of methacryloxypropyltrimethoxysilane(MPS); the second was to graft PMAA chains onto the surface of MNPs through radical polymerization. The success of the various surface functionalization steps was ascertained using FTIR and XPS. The as‐synthesized PMAA‐coated MNPs were effective in binding bovine serum albumin (BSA) with a high capacity of 1 300 mg · g⁻¹.

     

双层表面活性剂分散制备水基磁流体

Fe₃O₄ magnetic particles were synthesize by chemical co-precipitation. Sodium oleate and poly(ethylene glycol)-4000 were used as bilayer surfactants to envelope the ultra-fine Fe₃O₄ particles. Then stabilized water base magnetic fluid was obtained. Experiments indicated that surfactants and pH value of the solution had great effect on the stability and size of the magnetic fluid when Fe₃O₄ particles were synthesized and enveloped. It was the first time to employ this method to prepare magnetic fluid. Using laser diffraction particle size analyzer we found that the average diameter of magnetic fluid was lessen than 84 nanometer. Its magnetization was measured on magnetic balance and the result amounted to 3.84×10³A·m^-1. Further more， XRD and IR analysis measurements were employed to substantiate the existence of Fe₃O₄ and surfactant structure. The magnetic fluid can be used as tar-geted-part of nanometer targeted drug delivery system.     

Microbial Cells with a Fe3O4 Doped Hydrogel Extracellular Matrix: Manipulation of Living Cells by Magnetic Stimulus

This study aims to develop an effective method to control motile microorganisms and enable their manipulation as functional ‘live micro/nano robots'. A novel strategy based on Fe₃O₄ nanoparticle‐doped alginate hydrogel is developed to fashion an artificial extracellular matrix (ECM) for microbial cells (e.g., Saccharomyces cerevisiae and Flavobacterium heparinum). During this strategy, a single layer of alginate hydrogel is coated around the microbial cells doped with Fe₃O₄ nanoparticles to form the alg‐mag‐cells. Transmission electron microscopy shows that Fe₃O₄ nanoparticles are uniformly distributed in the hydrogel shell. Together with maintaining the cell activity and metabolism, the hydrogel coated microbial cells demonstrate high magnetic responsiveness in an external magnetic field and are able to form micro‐scaled patterns using the magnetic template designed in this study. This strategy provides a building block to fabricate advanced biological models, medical therapeutic products, and non‐medical biological systems using different microorganisms.

     

Polarized Neutron Diffraction as a Tool for Mapping Molecular Magnetic Anisotropy: Local Susceptibility Tensors in CoII Complexes

Polarized neutron diffraction (PND) experiments were carried out at low temperature to characterize with high precision the local magnetic anisotropy in two paramagnetic high‐spin cobalt(II) complexes, namely [Co^II(dmf)₆](BPh₄)₂ ( 1 ) and [Co^II₂(sym‐hmp)₂](BPh₄)₂ ( 2 ), in which dmf=N,N‐dimethylformamide; sym‐hmp=2,6‐bis[(2‐hydroxyethyl)methylaminomethyl]‐4‐methylphenolate, and BPh₄^?=tetraphenylborate. This allowed a unique and direct determination of the local magnetic susceptibility tensor on each individual Co^II site. In compound 1 , this approach reveals the correlation between the single‐ion easy magnetization direction and a trigonal elongation axis of the Co^II coordination octahedron. In exchange‐coupled dimer 2 , the determination of the individual Co^II magnetic susceptibility tensors provides a clear outlook of how the local magnetic properties on both Co^II sites deviate from the single‐ion behavior because of antiferromagnetic exchange coupling.     

Calculation of magnetic properties of HF,H2O,NH3, and CH4 molecules using a longitudinal gauge for the vector potential

A transformation of the transverse Coulomb vector potential was implemented to calculate molecular magnetic properties via the random-phase approximation (RPA) within the framework of a “longitudinal gauge.” In this gauge, the diamagnetic contribution to magnetic susceptibility is a tensor with equal diagonal components as in atoms, irrespective of molecular symmetry, whereas diagonal and average diamagnetic contributions to the nuclear magnetic shielding are the same as in the Coulomb gauge. Near-Hartree–Fock magnetic susceptibility and nuclear magnetic shielding tensors were evaluated for a set of small molecules, HF, H₂O, NH₃, and CH₄, employing extended Gaussian basis sets. The peculiar features of the longitudinal gauge, and the fulfillment of a series of sum rules involving the virial operator, which must be satisfied to guarantee gauge invariance of total magnetic tensors, were exploited to check the degree of convergence of theoretical values and to estimate the corresponding Hartree–Fock limit for the properties. © 1998 John Wiley & Sons, Inc. Int J Quant Chem 66 : 31–45, 1998