Visible‐Light‐Driven CO2 Reduction by Mesoporous Carbon Nitride Modified with Polymeric Cobalt Phthalocyanine

The integration of molecular catalysts with low‐cost, solid light absorbers presents a promising strategy to construct catalysts for the generation of solar fuels. Here, we report a photocatalyst for CO₂ reduction that consists of a polymeric cobalt phthalocyanine catalyst (CoPPc) coupled with mesoporous carbon nitride (mpg‐CN_x) as the photosensitizer. This precious‐metal‐free hybrid catalyst selectively converts CO₂ to CO in organic solvents under UV/Vis light (AM 1.5G, 100 mW cm^?2, λ>300 nm) with a cobalt‐based turnover number of 90 for CO after 60 h. Notably, the photocatalyst retains 60 % CO evolution activity under visible light irradiation (λ>400 nm) and displays moderate water tolerance. The in situ polymerization of the phthalocyanine allows control of catalyst loading and is key for achieving photocatalytic CO₂ conversion.     

A Highly Selective Copper–Indium Bimetallic Electrocatalyst for the Electrochemical Reduction of Aqueous CO2 to CO

The challenge in the electrochemical reduction of aqueous carbon dioxide is in designing a highly selective, energy‐efficient, and non‐precious‐metal electrocatalyst that minimizes the competitive reduction of proton to form hydrogen during aqueous CO₂ conversion. A non‐noble metal electrocatalyst based on a copper‐indium (Cu‐In) alloy that selectively converts CO₂ to CO with a low overpotential is reported. The electrochemical deposition of In on rough Cu surfaces led to Cu‐In alloy surfaces. DFT calculations showed that the In preferentially located on the edge sites rather than on the corner or flat sites and that the d‐electron nature of Cu remained almost intact, but adsorption properties of neighboring Cu was perturbed by the presence of In. This preparation of non‐noble metal alloy electrodes for the reduction of CO₂ provides guidelines for further improving electrocatalysis.     

钴单原子的双重限域制备策略及高效CO2电还原性能

将锌钴双掺杂的金属有机框架(MOFs)纳米颗粒(ZnCo-ZIF)与聚丙烯腈(PAN)混溶形成前驱体溶液, 通过静电纺丝与高温热化学反应, 获得了一种多孔碳纳米纤维负载的钴单原子催化剂(A-Co@PCFs). 高温热解时, 聚丙烯腈分解碳化形成碳纳米纤维主体, MOFs纳米颗粒结构坍塌伴随锌组分的挥发, 在纤维表面形成了丰富的多级孔结构. 由于碳纳米纤维和孔道结构的双重限域作用, 使钴组分不能聚集成钴纳米颗粒, 而是形成高度分散的钴单原子. 电化学测试结果表明, 该钴单原子催化剂可将CO₂电还原为CO, 在-0.66 V(vs. RHE)下, CO的法拉第效率可达94%. 并且经过60 h的耐久性测试, 其催化性能没有明显的性能衰减, 显示出较高的稳定性. A-Co@PCFs的高活性与高稳定性可归因于材料的多孔结构和高度分散的钴原子, 这也使其具有代替贵金属催化剂的可能性.     

Atomically Dispersed Molybdenum Catalysts for Efficient Ambient Nitrogen Fixation

NH₃ synthesis by the electrocatalytic N₂ reduction reaction (NRR) under ambient conditions is an appealing alternative to the currently employed industrial method—the Haber–Bosch process—that requires high temperature and pressure. We report single Mo atoms anchored to nitrogen‐doped porous carbon as a cost‐effective catalyst for the NRR. Benefiting from the optimally high density of active sites and hierarchically porous carbon frameworks, this catalyst achieves a high NH₃ yield rate (34.0±3.6 μg h^?1 mg_cat.^?1) and a high Faradaic efficiency (14.6±1.6 %) in 0.1 m KOH at room temperature. These values are considerably higher compared to previously reported non‐precious‐metal electrocatalysts. Moreover, this catalyst displays no obvious current drop during a 50 000 s NRR, and high activity and durability are achieved in 0.1 m HCl. The findings provide a promising lead for the design of efficient and robust single‐atom non‐precious‐metal catalysts for the electrocatalytic NRR.     

High‐Curvature Transition‐Metal Chalcogenide Nanostructures with a Pronounced Proximity Effect Enable Fast and Selective CO2 Electroreduction

A considerable challenge in the conversion of carbon dioxide into useful fuels comes from the activation of CO₂ to CO₂^.? or other intermediates, which often requires precious‐metal catalysts, high overpotentials, and/or electrolyte additives (e.g., ionic liquids). We report a microwave heating strategy for synthesizing a transition‐metal chalcogenide nanostructure that efficiently catalyzes CO₂ electroreduction to carbon monoxide (CO). We found that the cadmium sulfide (CdS) nanoneedle arrays exhibit an unprecedented current density of 212 mA cm^?2 with 95.5±4.0 % CO Faraday efficiency at ?1.2 V versus a reversible hydrogen electrode (RHE; without iR correction). Experimental and computational studies show that the high‐curvature CdS nanostructured catalyst has a pronounced proximity effect which gives rise to large electric field enhancement, which can concentrate alkali‐metal cations resulting in the enhanced CO₂ electroreduction efficiency.     

Ordered Porous Nitrogen‐Doped Carbon Matrix with Atomically Dispersed Cobalt Sites as an Efficient Catalyst for Dehydrogenation and Transfer Hydrogenation of N‐Heterocycles

Single‐atom catalysts (SACs) have been explored widely as potential substitutes for homogeneous catalysts. Isolated cobalt single‐atom sites were stabilized on an ordered porous nitrogen‐doped carbon matrix (ISAS‐Co/OPNC). ISAS‐Co/OPNC is a highly efficient catalyst for acceptorless dehydrogenation of N‐heterocycles to release H₂. ISAS‐Co/OPNC also exhibits excellent catalytic activity for the reverse transfer hydrogenation (or hydrogenation) of N‐heterocycles to store H₂, using formic acid or external hydrogen as a hydrogen source. The catalytic performance of ISAS‐Co/OPNC in both reactions surpasses previously reported homogeneous and heterogeneous precious‐metal catalysts. The reaction mechanisms are systematically investigated using first‐principles calculations and it is suggested that the Eley–Rideal mechanism is dominant.     

Controlling the Product Platform of Carbon Dioxide Reduction: Adaptive Catalytic Hydrosilylation of CO2 Using a Molecular Cobalt(II) Triazine Complex

The catalytic reduction of carbon dioxide (CO₂) is considered a major pillar of future sustainable energy systems and chemical industries based on renewable energy and raw materials. Typically, catalysts and catalytic systems are transforming CO₂ preferentially or even exclusively to one of the possible reduction levels and are then optimized for this specific product. Here, we report a cobalt‐based catalytic system that enables the adaptive and highly selective transformation of carbon dioxide individually to either the formic acid, the formaldehyde, or the methanol level, demonstrating the possibility of molecular control over the desired product platform.     

N‐Doped Sub‐3 nm Co Nanoparticles as Highly Efficient and Durable Aerobic Oxidative Coupling Catalysts

A nano‐coating associated with sulfuric acid leaching protocol was developed to prepare N‐doped sub‐3 nm Co‐based nanoparticle catalyst (Co?N/C) using melamine–formaldehyde resin as the N‐containing precursor, active carbon as the support, and Co(NO₃)₂ as the Co‐containing precursor. By thermal treatment under nitrogen atmosphere at 800 °C and leached with sulfuric acid solution, a stable and highly dispersive Co?N coordination structure was uniformly dispersed on the formed Co?N/C catalyst with a Co loading of 0.47 wt % and Co nanoparticle size of 2.55 nm. The Co?N/C catalyst was characterized with XRD, XPS, Raman, SEM, TEM, ICP, and elemental analysis. The Co?N/C catalyst showed extremely high catalytic efficiency with a TON of 257 for the aerobic oxidative coupling of aldehydes with methanol to directly synthesize methyl esters with molecular oxygen as the final oxidant. The Co?N/C catalyst also showed broad substrate range and stable recyclability. After recycling for 7 times, no obvious deactivation was detected. It was confirmed that the sub‐3 nm Co?N coordination structure formed between metallic Co nanoparticles and pyridinic nitrogen doping into graphitic layers functions as the active site to activate molecular oxygen for the β‐H elimination from generated hemiacetal intermediates to produce methyl esters. The nano‐coating associated with acid leaching protocol provides a novel strategy to prepare highly efficient non‐precious metal‐based catalysts.     

Co@Co3O4 Encapsulated in Carbon Nanotube‐Grafted Nitrogen‐Doped Carbon Polyhedra as an Advanced Bifunctional Oxygen Electrode

Efficient reversible oxygen electrodes for both the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) are vitally important for various energy conversion devices, such as regenerative fuel cells and metal–air batteries. However, realization of such electrodes is impeded by insufficient activity and instability of electrocatalysts for both water splitting and oxygen reduction. We report highly active bifunctional electrocatalysts for oxygen electrodes comprising core–shell Co@Co₃O₄ nanoparticles embedded in CNT‐grafted N‐doped carbon‐polyhedra obtained by the pyrolysis of cobalt metal–organic framework (ZIF‐67) in a reductive H₂ atmosphere and subsequent controlled oxidative calcination. The catalysts afford 0.85 V reversible overvoltage in 0.1 m KOH, surpassing Pt/C, IrO₂, and RuO₂ and thus ranking them among one of the best non‐precious‐metal electrocatalysts for reversible oxygen electrodes.     

Titanium Dioxide‐Grafted Copper Complexes: High‐Performance Electrocatalysts for the Oxygen Reduction Reaction in Alkaline Media

The sluggish kinetics of the oxygen reduction reaction (ORR) at the cathodes of fuel cells significantly hampers fuel cell performance. Therefore, the development of high‐performance, non‐precious‐metal catalysts as alternatives to noble metal Pt‐based ORR electrocatalysts is highly desirable for the large‐scale commercialization of fuel cells. TiO₂‐grafted copper complexes deposited on multiwalled carbon nanotubes (CNTs) form stable and efficient electrocatalysts for the ORR. The optimized catalyst composite CNTs@TiO₂–ZA–[Cu(phen)(BTC)] shows surprisingly high selectivity for the 4 e^? reduction of O₂ to water (approximately 97 %) in alkaline solution with an onset potential of 0.988 V vs. RHE, and demonstrates superior stability and excellent tolerance for the methanol crossover effect in comparison to a commercial Pt/C catalyst. The copper complexes were grafted onto the surface of TiO₂ through coordination of an imidazole‐containing ligand, zoledronic acid (ZA), which binds to TiO₂ through its bis‐phosphoric acid anchoring group. Rational optimization of the copper catalyst’s ORR performance was achieved by using an electron‐deficient ligand, 5‐nitro‐1,10‐phenanthroline (phen), and bridging benzene‐1,3,5‐tricarboxylate (BTC). This facile approach to the assembly of copper catalysts on TiO₂ with rationally tuned ORR activity will have significant implications for the development of high‐performance, non‐precious‐metal ORR catalysts.     

Metal‐Free Hydrosilylation Polymerization by Borane Catalyst

The first example of metal‐free hydrosilylation polymerization between dienes and disilanes is developed by using a borane catalyst, B(C₆F₅)₃ to replace precious transition‐metal‐based systems. Under the easy‐to‐handle and mild conditions, a step‐growth polymerization of two readily available diene and disilane units was achieved with high degrees of polymerization. Various combinations of dienes and disilanes produced polycarbosilanes with a broad range of structures and properties.     

Concerning the Deactivation of Cobalt(III)‐Based Porphyrin and Salen Catalysts in Epoxide/CO2 Copolymerization

Functioning as active catalysts for propylene oxide (PO) and carbon dioxide copolymerization, cobalt(III)‐based salen and porphyrin complexes have drawn great attention owing to their readily modifiable nature and promising catalytic behavior, such as high selectivity for the copolymer formation and good regioselectivity with respect to the polymer microstructure. Both cobalt(III)–salen and porphyrin catalysts have been found to undergo reduction reactions to their corresponding catalytically inactive cobalt(II) species in the presence of propylene oxide, as evidenced by UV/Vis and NMR spectroscopies and X‐ray crystallography (for cobalt(II)–salen). Further investigations on a TPPCoCl (TPP=tetraphenylporphyrin) and NaOMe system reveal that such a catalyst reduction is attributed to the presence of alkoxide anions. Kinetic studies of the redox reaction of TPPCoCl with NaOMe suggests a pseudo‐first order in cobalt(III)–porphyrin. The addition of a co‐catalyst, namely bis(triphenylphosphine)iminium chloride (PPNCl), into the reaction system of cobalt(III)–salen/porphyrin and PO shows no direct stabilizing effect. However, the results of PO/CO₂ copolymerization by cobalt(III)–salen/porphyrin with PPNCl suggest a suppressed catalyst reduction. This phenomenon is explained by a rapid transformation of the alkoxide into the carbonate chain end in the course of the polymer formation, greatly shortening the lifetime of the autoreducible PO‐ring‐opening intermediates, cobalt(III)–salen/porphyrin alkoxides.     

A Fully Integrated Continuous‐Flow System for Asymmetric Catalysis: Enantioselective Hydrogenation with Supported Ionic Liquid Phase Catalysts Using Supercritical CO2 as the Mobile Phase

A continuous‐flow process based on a chiral transition‐metal complex in a supported ionic liquid phase (SILP) with supercritical carbon dioxide (scCO₂) as the mobile phase is presented for asymmetric catalytic transformations of low‐volatility organic substrates at mild reaction temperatures. Enantioselectivity of >99 % ee and quantitative conversion were achieved in the hydrogenation of dimethylitaconate for up to 30 h, reaching turnover numbers beyond 100 000 for the chiral QUINAPHOS–rhodium complex. By using an automated high‐pressure continuous‐flow setup, the product was isolated in analytically pure form without the use of any organic co‐solvent and with no detectable catalyst leaching. Phase‐behaviour studies and high‐pressure NMR spectroscopy assisted the localisation of optimum process parameters by quantification of substrate partitioning between the IL and scCO₂. Fundamental insight into the molecular interactions of the metal complex, ionic liquid and the surface of the support in working SILP catalyst materials was gained by means of systematic variations, spectroscopic studies and labelling experiments. In concert, the obtained results provided a rationale for avoiding progressive long‐term deactivation. The optimised system reached stable selectivities and productivities that correspond to 0.7 kg L ^?1 h^?1 space–time yield and at least 100 kg product per gram of rhodium, thus making such processes attractive for larger‐scale application.     

Ionic Liquids as Precursors for Efficient Mesoporous Iron‐Nitrogen‐Doped Oxygen Reduction Electrocatalysts

A ferrocene‐based ionic liquid (Fe‐IL) is used as a metal‐containing feedstock with a nitrogen‐enriched ionic liquid (N‐IL) as a compatible nitrogen content modulator to prepare a novel type of non‐precious‐metal–nitrogen–carbon (M‐N‐C) catalysts, which feature ordered mesoporous structure consisting of uniform iron oxide nanoparticles embedded into N‐enriched carbons. The catalyst Fe¹⁰@NOMC exhibits comparable catalytic activity but superior long‐term stability to 20 wt % Pt/C for ORR with four‐electron transfer pathway under alkaline conditions. Such outstanding catalytic performance is ascribed to the populated Fe (Fe₃O₄) and N (N2) active sites with synergetic chemical coupling as well as the ordered mesoporous structure and high surface area endowed by both the versatile precursors and the synthetic strategy, which also open new avenues for the development of M‐N‐C catalytic materials.     

Non‐3d Metal Modulation of a Cobalt Imidazolate Framework for Excellent Electrocatalytic Oxygen Evolution in Neutral Media

Cobalt imidazolate frameworks are classical electrocatalysts for the oxygen evolution reaction (OER) but suffer from the relatively low activity. Here, a non‐3d metal modulation strategy is presented for enhancing the OER activity of cobalt imidazolate frameworks. Two isomorphous frameworks [Co₄(MO₄)(eim)₆] (M=Mo or W, Heim=2‐ethylimidazole) having Co(eim)₃(MO₄) units and high water stabilities were designed and synthesized. In different neutral media, the Mo‐modulated framework coated on a glassy carbon electrode shows the best OER performances (1 mA cm^?2 at an overpotential of 210 mV in CO₂‐saturated 0.5 m KHCO₃ electrolyte and 2/10/22 mA cm^?2 at overpotential of 388/490/570 mV in phosphate buffer solution) among non‐precious metal catalysts and even outperforms RuO₂. Spectroscopic measurements and computational simulations revealed that the non‐3d metals modulate the electronic structure of Co for optimum reactant/product adsorption and tailor the energy of rate‐determining step to a more moderate value.     

Transition‐Metal‐Free Catalytic Reduction of Carbon Dioxide

Metal‐free systems, including frustrated Lewis pairs (FLPs) have been shown to bind CO₂. By reducing the Lewis acidity and basicity of the ambiphilic system, it is possible to generate active catalysts for the deoxygenative hydroboration of carbon dioxide to methanol derivatives with conversion rates comparable to those of transition‐metal‐based catalysts.     

A Precious‐Metal‐Free Hybrid Electrolyzer for Alcohol Oxidation Coupled to CO2‐to‐Syngas Conversion

Electrolyzers combining CO₂ reduction (CO₂R) with organic substrate oxidation can produce fuel and chemical feedstocks with a relatively low energy requirement when compared to systems that source electrons from water oxidation. Here, we report an anodic hybrid assembly based on a (2,2,6,6‐tetramethylpiperidin‐1‐yl)oxyl (TEMPO) electrocatalyst modified with a silatrane‐anchor ( STEMPO ), which is covalently immobilized on a mesoporous indium tin oxide (mesoITO) scaffold for efficient alcohol oxidation (AlcOx). This molecular anode was subsequently combined with a cathode consisting of a polymeric cobalt phthalocyanine on carbon nanotubes to construct a hybrid, precious‐metal‐free coupled AlcOx–CO₂R electrolyzer. After three‐hour electrolysis, glycerol is selectively oxidized to glyceraldehyde with a turnover number (TON) of ≈1000 and Faradaic efficiency (FE) of 83 %. The cathode generated a stoichiometric amount of syngas with a CO:H₂ ratio of 1.25±0.25 and an overall cobalt‐based TON of 894 with a FE of 82 %. This prototype device inspires the design and implementation of nonconventional strategies for coupling CO₂R to less energy demanding, and value‐added, oxidative chemistry.     

Contribution of the ligand to the electroreduction of CO2 catalyzed by a cobalt(II) macrocyclic complex

The electrochemical reduction of carbon dioxide using hexa-aza-macrocycles derived from the condensation of 1,10-phenanthroline and its Co(II) complex as an electrocatalyst dissolved in dimethylformamide has been studied by cyclic voltammetry and UV-visible spectroscopy. The ligand does not show catalytic activity and only generates hydrogen when it is reduced under carbon dioxide. The cobalt complex shows electrocatalytic activity toward the reduction of carbon dioxide, generating carbon monoxide and formic acid. Cyclic voltammetry and UV-visible spectroscopy show that the active site for the reduction is the metal center in oxidation state (I), although the reduced cobalt center alone is not enough to promote reduction of the carbon dioxide. Electrolysis at controlled potential shows that only at potentials corresponding to reduction of the ligand (second reduction) does carbon dioxide reduction occur. Cobalt(I) probably reacts with CO₂ forming a non-isolated intermediate which, when reduced, gives CO and formic acid. The second reduction that takes place on the ligand regenerates the catalyst and gives products, thus becoming the rate-determining step of the reaction.     

Ni3N as an Active Hydrogen Oxidation Reaction Catalyst in Alkaline Medium

Hydroxide‐exchange membrane fuel cells can potentially utilize platinum‐group‐metal (PGM)‐free electrocatalysts, offering cost and scalability advantages over more developed proton‐exchange membrane fuel cells. However, there is a lack of non‐precious electrocatalysts that are active and stable for the hydrogen oxidation reaction (HOR) relevant to hydroxide‐exchange membrane fuel cells. Here we report the discovery and development of Ni₃N as an active and robust HOR catalyst in alkaline medium. A supported version of the catalyst, Ni₃N/C, exhibits by far the highest mass activity and break‐down potential for a PGM‐free catalyst. The catalyst also exhibits Pt‐like activity for hydrogen evolution reaction (HER) in alkaline medium. Spectroscopy data reveal a downshift of the Ni d band going from Ni to Ni₃N and interfacial charge transfer from Ni₃N to the carbon support. These properties weaken the binding energy of hydrogen and oxygen species, resulting in remarkable HOR activity and stability.     

The Direct Electron Transfer of Iron‐containing Metal Organic Frameworks (Mil‐100) and Its Catalysis for the Oxygen Reduction Reaction in Room‐Temperature Alkaline Media on a Glass Carbon Electrode

The most common electrocatalysts for the oxygen reduction reaction (ORR) are platinum‐based ones. This work demonstrates the performance of iron‐containing metal organic frameworks (MOFs) as non‐platinum‐based nano‐electrocatalysts for ORR in an alkaline medium. As a new non‐platinum catalyst to achieve the active sites for the ORR, Mil‐100 (Fe) nanoparticles were used in aqueous KOH by the rotating‐disk electrode method. The main objectives of this study are the investigations on the electron transfer number (n ), Tafel slope, and catalytic performance. The particles size of the obtained powders is in the nanoscale range (approximately 25 nm). The electron transfer number for the ORR on the surface of iron‐containing catalyst is approximately 4, and the Tafel slope of diffusion‐corrected kinetic current density is ~50.7 mV per decade at low overpotential. This work might extend a new non‐precious‐metal catalyst structure for ORR for use in low‐temperature fuel cells.