高碘酸钾-鲁米诺后化学发光反应的研究——流动注射-后化学发光法测定异烟肼

实验发现了异烟肼在高碘酸钾-鲁米诺化学发光反应体系中的后化学发光反应。在对这一后化学发光反应的动力学性质、化学发光光谱、荧光光谱、紫外可见吸收光谱以及一些相关问题研究的基础上,讨论了其可能的反应机理;建立了利用此后化学发光反应测定异烟肼的流动注射化学发光新方法。方法的线性范围为1.0×10-9~4.0×10-7g/mL,检出限为6×10-10g/mL,对5.0×10-8g/mL的异烟肼进行11次平行测定的相对标准偏差为1.7%。此法已用于异烟肼片剂中异烟肼含量的测定,结果与药典法测定值一致。     

流动注射化学发光法测定河水中对苯二酚

在碱性介质中,高碘酸钾氧化鲁米诺产生化学发光,对苯二酚对此反应具有极强的增敏作用,据此建立了鲁米诺-高碘酸钾-对苯二酚化学发光体系测定对苯二酚的方法。对苯二酚溶液浓度在1.0×10-8~1.5×10-7mol.L-1范围内与化学发光强度呈线性关系,检出限为8.5×10-9mol.L-1,用于河水中对苯二酚的测定并测得其回收率在93.4%~104.4%之间。探讨了对苯二酚的增敏机理。     

铁氰化钾-鲁米诺体系后化学发光反应及其分析应用研究 ————-分子印迹-后化学发光法测定双嘧达莫

研究了双嘧达莫在铁氰化钾-鲁米诺化学发光反应体系中的后化学发光反应, 并在研究其反应的动力学性质、化学发光光谱、荧光光谱以及一些相关问题的基础上, 探讨了反应机理; 合成了双嘧达莫的分子印迹聚合物, 以此聚合物为分子识别物质, 利用铁氰化钾-鲁米诺-双嘧达莫后化学发光体系, 建立了测定双嘧达莫的高选择性分子印迹-后化学发光分析方法. 所建方法的线性范围为1.0×10-8-1.0×10-6 g/mL(r=0.999 2), 检出限为3×10-9 g/mL, 相对标准偏差为2.7%(1.0×10-7 g/mL双嘧达莫, n=11).     

鲁米诺化学发光分析法研究进展

从化学发光反应机理和应用进展两个方面对鲁米诺-过氧化氢、鲁米诺-铁氰化钾、鲁米诺-碘化物、鲁米诺-高锰酸钾和鲁米诺-溶解氧等化学发光体系进行了综述;指出鲁米诺化学发光体系是应用最为广泛的一类化学发光体系,同时对鲁米诺化学发光分析法的发展方向进行了展望.     

溴酸钾-鲁米诺后化学发光法检测水中微量偏二甲肼

实验发现偏二甲肼(UDMH)在溴酸钾-鲁米诺化学发光反应体系中的后化学发光反应.在对这一后化学发光反应的动力学性质、发光条件,包括溴酸钾浓度、鲁米诺浓度、管长、流速和酸碱度条件等研究的基础上,建立了后化学发光反应法测定偏二甲肼的新方法,并讨论了其可能的反应机理.该方法的线性范围为1.0×10-7～1.0×10-5g/L...     

流动注射-鲁米诺-高碘酸钾-过氧化氢体系的化学发光行为及其应用

详细研究了流动注射－鲁米诺－高碘酸钾－过氧化氢体系化学发光行为，给出了反应的最佳条件。拟定了一种化学发光测定过氧化氢的新方法。方法的检测限为３．０Ｘ１０－８ｍｏｌ／ＬＨ２Ｏ２；线性范围为２．０×１０－７～６．０×１０－４ｍｏｌ／Ｌ。评价了该体系的应用前景。     

纳米SnO2增敏鲁米诺化学发光的研究与应用

采用溶胶-凝胶法制得平均粒径约10 nm的SnO2粒子.将该纳米SnO2粒子加入碱性鲁米诺-O2化学发光体系,体系的化学发光强度明显增强,这种增敏作用与纳米SnO2的加入量以及体系中溶解氧的质量浓度有关,基于此得出了纳米SnO2存在下溶解氧质量浓度与鲁米诺化学发光强度之间的线性关系,可用于溶解氧测定,检出限达0.3 mg/L,该纳米增敏化学发光体系有望用于进一步提高基于鲁米诺化学发光测定方法的灵敏度.文中还应用紫外-可见光谱和荧光光谱研究了这种增敏作用的机理,并应用该体系考察了水果的抗氧化能力.     

鲁米诺-锰(Ⅱ)-高碘酸钾化学发光体系测定痕量锰的研究

本文提出1种以三乙醇胺作活化剂,基于鲁米诺-锰(Ⅱ)-高碘酸钾化学发光体系高灵敏度、高选择性测定痕量锰的分析方法。检测限达8×10^-6μg/mLMn(Ⅱ)。Mn(Ⅱ)浓度在10^-5～0.1μg/mL范围内呈良好的线性关系。测定1.0×10^-3μg/mLMn(Ⅱ)的相对标准偏差小于±3％。应用于井水及人发样品中锰的测定,结果令人满意。     

反向流动注射化学发光法测定盐酸乙胺丁醇

基于盐酸乙胺丁醇与高碘酸钾～鲁米诺反应产生很强的化学发光,结合反向流动注射技术,建立了流动注射化学发光法测定盐酸乙胺丁醇的新方法。在优化的实验条件下,该法的线性范围为4.0×10-8～2×10-5g/mL,检出限为8×10-9g/mL,对6.0×10-7g/mL盐酸乙胺丁醇进行11次平行测定,方法的相对标准偏差为1.9%。该法可用于片剂中盐酸乙胺丁醇的测定。     

流动注射化学发光法检测甲基嘧啶磷残留

研究发现,在碱性介质中甲基嘧啶磷能够有效增强鲁米诺-H2O2体系的化学发光。据此,结合流动注射分析法,建立了测定甲基嘧啶磷的流动注射化学发光分析方法,并对可能的反应机理进行了探讨。考察了甲基嘧啶磷-鲁米诺-H2O2体系的化学发光反应动力学以及反应体系pH、鲁米诺浓度、H2O2浓度、流速、进样体积等因素对化学发光的影响。结果表明:在最佳条件下,甲基嘧啶磷在5.0×10-8～1.0×10-5g/mL的浓度范围内与发光强度呈良好的线性关系,检出限(S/N=3)为2.5×10-8g/mL。将该体系应用于加标小麦样品测定,回收率为94.7%～113.0%,相对标准偏差为2.2%～3.6%。     

流动注射后化学发光法测定盐酸阿比朵尔

研究了盐酸阿比朵尔在鲁米诺-K3Fe(CN)6化学发光反应体系中的后化学发光反应. 据此建立了测定盐酸阿比朵尔的流动注射后化学发光分析法. 方法的线性范围为6.0×10-9～1.0×10-7 g/mL, 检出限(3σ)为2×10-9 g/mL. 对4.0×10-8 g/mL的盐酸阿比朵尔溶液连续11次平行测定, RSD=1.3%. 方法已用于盐酸阿比朵尔胶囊及尿样中盐酸阿比朵尔含量的测定. 在对这一后化学发光反应的动力学性质、化学发光光谱、紫外可见吸收光谱以及一些相关问题研究的基础上, 提出了可能的反应机理.     

Investigating the post-chemiluminescence behavior of phenothiazine medications in the luminol–potassium ferricyanide system: molecular imprinting–post-chemiluminescence method for the determination of chlorpromazine hydrochloride

A new post-chemiluminescence (PCL) phenomenon was observed when phenothiazine medications were injected into the reaction mixture after the chemiluminescence (CL) reaction of luminol and potassium ferricyanide had finished. A possible reaction mechanism was proposed based on studies of the kinetic characteristics of the CL, CL spectra, fluorescence spectra, and on other experiments. The feasibility of determining various phenothiazine medications by utilizing these PCL reactions was examined. A molecular imprinting–post-chemiluminescence (MI-PCL) method was established for the determination of chlorpromazine hydrochloride using a chlorpromazine hydrochloride-imprinted polymer (MIP) as the recognition material. The method displayed high selectivity and high sensitivity. The linear range of the method was 1.0×10⁻⁸∼1.0×10⁻⁶, with a linear correlation coefficient of 0.9985. The detection limit was 3×10⁻⁹ g/ml chlorpromazine hydrochloride, and the relative standard deviation for a 1.0×10⁻⁷ g/ml chlorpromazine hydrochloride solution was 4.0% (n=11). The method has been applied to the determination of chlorpromazine hydrochloride in urine and animal drinking water with satisfactory results.      

Post-chemiluminescence phenomenon of NBS-luminol reactions and their applications to flow injection analysis of piroxicam.

A new post-chemiluminescence (PCL) reaction was observed when piroxicam was injected into the reaction mixture after the CL reaction of N-bromosuccinimide (NBS) and luminol. A possible reaction mechanism was proposed based on the studies of the CL kinetic characteristics, the CL spectra, fluorescence spectra and other experiments. A new flow injection CL method for the determination of piroxicam was established based on the PCL reaction. The relative standard deviation (RSD) for the determination of piroxicam was 1.2% (n = 11, c = 2.0 x 10(-6) g/ml). The CL intensity responded linearly to the concentration of piroxicam in the range 1.0 x 10(-7) - 1.0 x 10(-5) g/ml (r = 0.9991). The detection limit was 4.0 x 10(-8) g/ml. The method had been applied to the determination of piroxicam in tablets with satisfactory results.     

Post‐chemiluminescence Method of the Determination of Loperamide Hydrochloride in Human Plasma and Pharmaceutical by Using Dichlorofluorescein as Chemiluminescence Reagent

Abstract

A post‐chemiluminescence (PCL) was observed when loperamide hydrochloride solution was injected into the reaction mixture after the finish of CL reaction of alkaline N‐Chlorosuccinimide (NCS) and dichlorofluorescein. Based on this phenomenon, a simple, sensitive and fast flow injection PCL method was established for the determination of loperamide hydrochloride. The possible mechanism for the PCL reaction was discussed via the investigation of the CL kinetic characteristics, the CL spectra, the fluorescence spectra. The PCL intensity responded linearly to the concentration of loperamide hydrochloride in the range 8.0×10^?10 to 6.0×10^?7 g · ml^?1 with a linear correlation of 0.9995. The detection limit was 4×10^?10 g · ml^?1. The relative standard deviation was 2.4% for 4.0×10^?8 g · ml^?1 loperamide hydrochloride (n=11). This method has been applied to the determination of loperamide hydrochloride in human plasma and pharmaceutical samples with satisfactory results.     

Determination of fenfluramine based on potassium permanganate-calcein chemiluminescence system

Calcein was found to be able to use as chemiluminescence reagent and post-chemiluminescence was observed when fenfluramine was injected into the mixture after the CL reaction of calcein–potassium permanganate. Based on this phenomenon, a flow injection CL method was established for the determination of fenfluramine. The possible CL mechanism was proposed. The CL intensity was correlated linearly with the concentration of fenfluramine over the range of 1.0 × 10⁻⁷ to 6.0 × 10⁻⁶ g mL⁻¹ and the detection limit was 6 × 10⁻⁸ g mL⁻¹. The relative standard deviation was 2.2% for 5.0 × 10⁻⁷ g mL⁻¹ fenfluramine (n = 11). This method was applied to the determination of fenfluramine in weight-reducing tonic successfully.     

流动注射后化学发光法测定异烟肼

本文发现了异烟肼在铁氰化钾-钙黄绿素化学发光反应体系中的后化学发光反应。优化了反应条件,建立了一种利用后化学发光反应测定异烟肼的流动注射化学发光分析法。方法的检出限为6×10-8g/mL, 相对标准偏差为1.8% (2.0×10-6 g/mL 异烟肼,n=11）,线性范围为2.0×10-7~1.0×10-5 g/mL。此法已用于异烟肼片剂中异烟肼含量的测定,结果与药典方法测定值一致。     

Flow-injection post chemiluminescence determination of atropine sulfate

A new post chemiluminescence (PCL) reaction was observed when atropine sulfate was injected into the reaction mixture after the finish of CL reaction of Ce(IV) and sodium sulfite. The possible mechanism for the PCL reaction was discussed via the investigation of the CL kinetic characteristics, the CL spectra, the UV absorption spectra and the fluorescence spectra of some related substances. The flow injection PCL method for the determination of atropine sulfate was established. The relative standard deviation (R.S.D.) was 2.8% (n = 11, c = 5.0 × 10⁻⁶ g mL⁻¹). The PCL intensity responded linearly to the concentration of atropine sulfate in the range 1.0 × 10⁻⁶ to 5.0 × 10⁻⁵ g mL⁻¹ with a linear correlation of 0.9947. The detection limit was 4 × 10⁻⁷ g mL⁻¹ atropine sulfate. The method had been applied to the determination of atropine sulfate in the tablets and the results were consistent with the method of Chinese pharmacopoeia.     

Flow injection chemiluminescent detection of trace Co(II) with dibromoalizarin violet-H2O2-CTMAB system

Chemiluminescence was observed when dibromoalizarin violet was oxidized with hydrogen peroxide in alkaline solution. Trace amounts of Co (II) catalysed this CL reaction strongly, especially in the presence of the cationic surfactant cetyltrimethylammonium bromide, and the CL intensity was proportional to the concentration of Co(II). A flow injection system with CL detection was established to investigate this CL system. The optimum conditions for this CL reaction were investigated in detail, and the optimized flow injection parameters were determined by the modified simplex method. A CL analytical method for determination of ultratrace amounts of Co (II) was developed with a detection limit of 4 pg/mL. It was used for analysis of natural water samples, and the results compare very well with those from GFAAS. A possible mechanism for this CL reaction is proposed on the basis of studying CL spectra, absorption spectra, fluorescent spectra and HMO treatment for the reagent molecule. The effects of various types of surfactants on CL reaction are also discussed.