卤素离子-富马酸酮替芬-联吡啶钌体系电化学发光的研究及应用

在卤素离子存在下,考察了富马酸酮替芬-Ru(bpy)32+体系在金电极上的电化学及其发光行为。结果表明:Br-对富马酸酮替芬-Ru(bpy)32+体系在金电极上发光行为具有显著的促进和增敏作用。据此,建立了一种高效、简便的富马酸酮替芬检测的新方法。在最佳实验条件下,富马酸酮替芬在1.0×10-4～1.0×10-7mol/L浓度范围内与相对发光强度呈线性关系,回归方程为I(counts)=1.73×108c+188.15(R2=0.9989),检出限(S/N=3)为4.29×10-8mol/L,连续平行测定富马酸酮替芬溶液(1×10-5mol/L)6次,发光强度的RSD为4.7%。回收率在99.5%～105.0%之间,RSD为2.3%(n=5)。该方法用于实际样品的测定,结果满意。     

盐酸氯丙嗪-联吡啶钌体系在多壁碳纳米管修饰电极上的电化学发光行为研究及盐酸氯丙嗪的测定

在玻碳电极上成功制备了多壁碳纳米管修饰电极(MWCNTs/GCE),优化了该修饰电极的制备条件.研究了联吡啶钌和盐酸氯丙嗪在该修饰电极上的电化学行为和电化学发光行为,建立了电化学发光法测定尿液中盐酸氯丙嗪的分析方法.结果表明,联吡啶钌-氯丙嗪体系在MWCNTs/GCE上表现出很好的电化学活性和电致化学发光响应,多壁碳纳米管不但增大了玻碳电极的比表面积而且加快了联吡啶钌在电极表面的电化学氧化,对联吡啶钌的电化学发光强度具有明显的增敏作用,同时盐酸氯丙嗪对联吡啶钌在该修饰电极上的电致化学发光具有很强的增敏作用.在0.1 mol/L的磷酸盐(pH 7.5)缓冲溶液中,盐酸氯丙嗪在该修饰电极上的检出限(S/N=3)为6.0×10-7 mol/L,在1.0×10-6 ～4.0×10-4 mol/L范围内浓度与相对发光强度呈线性关系(r=0.995 2).连续测定6.0×10-5 mol/L的盐酸氯丙嗪溶液13次,发光强度的RSD值为2.50%,表明该修饰电极具有较好的重复性.该方法已经成功地应用于尿样的检测.     

固定丝素蛋白膜中的联吡啶钌电化学发光行为的研究与应用

基于苯海拉明对联吡啶钌(Ru(bpy)2+3)的电化学发光的增敏作用和丝素蛋白-联吡啶钌复合膜修饰玻碳电极稳定好的特点,建立了一种以丝素蛋白多孔膜-联吡啶钌复合物修饰的玻碳电极电化学发光检测苯海拉明的新方法.结果表明,该修饰电极具有很好的电化学活性和电化学发光(ECL)响应.在最佳实验条件下,苯海拉明浓度在1.0×10-4～1.0×10-7 mol/L范围内与其相对发光强度呈良好的线性关系(r=0.9989); 检出限为2.3×10-7 mol/L(S/N=3).连续平行测定3.78×10-5 mol/L苯海拉明5次,发光强度的RSD为1.76%. 用于实际样品中苯海拉明的测定,结果满意.     

纳米石墨烯修饰电极电化学发光法测定盐酸氯丙嗪的研究

基于盐酸氯丙嗪对联吡啶钌电化学发光的增敏作用,以石墨烯(Graphene)和Nafion复合膜修饰的玻碳电极(GCE)为工作电极,建立了一种直接测定盐酸氯丙嗪的电化学发光新方法。最佳实验条件下,盐酸氯丙嗪浓度在8.0×10-7~1.2×10-4mol/L范围内与其相对发光强度呈良好线性关系(r=0.998 8),且在该修饰电极上的检出限(S/N=3)为4.0×10-7mol/L。连续测定4.0×10-6mol/L盐酸氯丙嗪溶液11次,发光强度值的相对标准偏差(RSD)为1.4%,表明该修饰电极具有较好的重复性和灵敏度。盐酸氯丙嗪的加标回收率为93%~104%,RSD(n=5)为4.1%。将该方法应用于药片中盐酸氯丙嗪的检测,结果满意。     

Silica sol/Nano-Au/PVA/L-cysteine修饰金电极电致化学发光测定甲氧氯普胺的研究

在甲氧氯普胺对联吡啶钌具有较好电化学发光增敏效果的基础上,制备出Silica sol/Nano-Au/PVA/L-cysteine修饰金电极,并通过电致化学发光法,考察了联吡啶钌及联吡啶钌-甲氧氯普胺体系在此电极上的电化学及电化学发光行为。该修饰电极对联吡啶钌-甲氧氯普胺体系有良好的电致化学发光响应特性;在最优条件下,在1.0×10-7~1.0×10-4mol/L范围内甲氧氯普胺浓度与其对应的电化学发光强度值线性关系良好,检出限(S/N=3)为1.40×10-9mol/L;通过平行测定1.0×10-5mol/L甲氧氯普胺溶液8次,发光强度值相对偏差(RSD)为1.8%,样品回收率在98.3%~104.4%之间,RSD为2.3%(n=5)。     

多壁纳米碳管/二氧化硅复合膜中的联吡啶钌电化学发光法测定氧氟沙星的研究与应用

基于氧氟沙星对联吡啶钌(Ru(bpy)_3~(2+))电化学发光的增敏作用,建立了一种以多壁纳米碳管(MWCNTs)/二氧化硅-联吡啶钌复合物修饰的玻碳电极电化学发光检测氧氟沙星的新方法.利用溶胶-凝胶(sol-gel)固定化稳定的优点和纳米碳管的电催化作用,提高了传感器的电流响应.在最佳实验条件下,氧氟沙星浓度在4.0×10~(-6) ～1.0×10~(-4) mol/L范围内与相对发光强度呈线性关系(r~2=0.994 8),检出限(S/N=3)为2.0×10~(-6) mol/L.连续平行测定2.4×10~(-5) mol/L的氧氟沙星溶液 5次,发光强度的RSD为1.8%.     

磺基水杨酸修饰电极联吡啶钌电化学发光体系测定可待因的研究

基于磷酸可待因对联吡啶钌在该电极上的电化学及其发光行为的增敏作用,建立了一种直接测定磷酸可待因的电化学发光新方法。在最佳实验条件下,磷酸可待因在1.0×10-4～4.0×10-6mol/L和4.0×10-6～2.0×10-7mol/L与相对发光强度呈线性关系,检出限为1.0×10-7mol/L(S/N=3)。连续测定4.0×10-7mol/l磷酸可待因5次,发光强度的RSD为2.7%。方法用于模拟尿样中磷酸可待因的测定,结果满意。     

纳米石墨烯修饰电极电化学发光法测定盐酸氯丙嗪的研究

基于盐酸氯丙嗪对联吡啶钌电化学发光的增敏作用,以石墨烯(Graphene)和Nafion复合膜修饰的玻碳电极(GCE)为工作电极,建立了一种直接测定盐酸氯丙嗪的电化学发光新方法。最佳实验条件下,盐酸氯丙嗪浓度在8.0×10-7 ~1.2×10-4 mol/L范围内与其相对发光强度呈良好线性关系(r=0.998 8),且在该修饰电极上的检出限(S/N=3)为4.0×10-7 mol/L。连续测定4.0×10-6 mol/L盐酸氯丙嗪溶液11次,发光强度值的相对标准偏差(RSD)为1.4%,表明该修饰电极具有较好的重复性和灵敏度。盐酸氯丙嗪的加标回收率为93%~104%,RSD(n=5)为4.1%。将该方法应用于药片中盐酸氯丙嗪的检测,结果满意。     

固定Ionic liquid/Silica sol/Nafion膜中的联吡啶钌电化学发光行为的研究及应用

制备了Ionic liquid/Silica sol/Nafion-联吡啶钌复合物膜修饰金电极。采用循环伏安(CV)和电致化学发光(ECL)法,考察了联吡啶钌和左氧氟沙星在此修饰电极上的电化学及其发光行为。结果表明,此修饰电极表现出很好的电化学活性和电化学发光响应。基于左氧氟沙星对固定化联吡啶钌在0.1 mol/L磷酸盐缓冲液中的弱电化学发光信号有较强的增敏作用,建立了电化学发光检测盐酸左氧氟沙星的新方法。在最佳实验条件下,左氧氟沙星浓度在1.0×10-7～1.0×10-4mol/L范围内与相对发光强度呈线性关系(r2=0.998 4),检出限(S/N=3)为1.59×10-9mol/L。连续平行测定2.2×10-5mol/L的左氧氟沙星溶液10次,发光强度的相对标准偏差(RSD)为3.6%。对样品进行回收率试验,回收率在95.6%～103.5%之间,RSD(n=5)为3.0%。该方法具有较高的选择性和灵敏度,样品处理简单快速,用于盐酸左氧氟沙星的测定,结果满意。     

3D石墨烯/SiO_2@Ru(bpy)_3~(2+)修饰电极电化学发光测定敌草隆的研究

利用敌草隆对三联吡啶钌电化学发光(ECL)的增敏作用,以3D石墨烯和二氧化硅固定三联吡啶钌纳米复合材料(Si O2@Ru(bpy)2+3)修饰的玻碳电极为工作电极,建立了一种直接快速检测敌草隆的电化学发光新方法。通过一步水热法合成了3D石墨烯以促进电子传递,油包水微乳液法合成Si O2@Ru(bpy)2+3以提高发光效率。在最佳实验条件下,敌草隆浓度的对数在9.08×10-11~9.08×10-7mol/L范围内与其相对发光强度呈良好的线性关系(r2=0.998 9),检出限(S/N=3)为1.18×10-12mol/L。连续测定2.00×10-8mol/L敌草隆10次,发光强度值的相对标准偏差(RSD)为4.2%,表明该方法具有良好的重复性。用该方法对青菜进行检测,回收率为99.3%~110.8%,结果满意。     

L-半胱氨酸修饰金电极电化学发光法测定罗红霉素

在裸金电极上制备了L-半胱氨酸自组装膜修饰电极(L-Cys-Au/SAM/CME).考察了联吡啶钌和罗红霉素在此修饰电极上的电化学及其发光行为.结果表明,此修饰电极表现出了很好的电化学活性和电化学发光(ECL)响应.基于罗红霉素的存在可增大了联吡啶钌的发光强度,建立了测定罗红霉素片的电化学发光分析方法.在最佳实验条件下,罗红霉素浓度在1.0×10-7～1.0×10-4 mol/L范围内与其相对发光强度呈线性关系,其线性回归方程为I=2×107C+384.02, r=0.9977; 检出限(S/N=3)为1.0×10-7 mol/L.连续测定1.8×10-5 mol/L罗红霉素10次,发光强度的RSD为1.93% , 表明此修饰电极具有较好的重现性,并将本方法用于罗红霉素片剂的检测.     

A Novel Electrogenerated Chemiluminescence (ECL) Sensor Based on Ru(bpy)32+‐Doped Titania Nanoparticles Dispersed in Nafion on Glassy Carbon Electrode

A novel electrogenerated chemiluminescence (ECL) sensor based on Ru(bpy)₃²⁺‐doped titania (RuDT) nanoparticles dispersed in a perfluorosulfonated ionomer (Nafion) on a glassy carbon electrode (GCE) was developed in this paper. The electroactive component‐Ru(bpy)₃²⁺ was entrapped within the titania nanoparticles by the inverse microemulsion polymerization process that produced spherical sensors in the size region of 38±3 nm. The RuDT nanoparticles were characterized by electrochemical, transmission electron and scanning microscopy technology. The Ru(bpy)₃²⁺ encapsulation interior of the titania nanoparticles maintains its ECL efficiency and also reduces Ru(bpy)₃²⁺ leaching from the titania matrix when immersed in water due to the electrostatic interaction. This is the first attempt to prepare the RuDT nanoparticles and extend the application of electroactive component‐doped nanoparticles into the field of ECL. Since a large amount of Ru(bpy)₃²⁺ was immobilized three‐dimensionally on the electrode, the Ru(bpy)₃²⁺ ECL signal could be enhanced greatly, which finally resulted in the increased sensitivity. The ECL analytical performance of this ECL sensor for tripropylamine (TPA) was investigated in detail. This sensor shows a detection limit of 1 nmol/L for TPA. Furthermore, the present ECL sensor displays outstanding long‐term stability.     

“Signal-on” Electrogenerated Chemiluminescence Biosensing Method for the Determination of Matrix Metalloproteinase 2

A simple, selective and sensitive “signal-on” electrogenerated chemiluminescence (ECL) biosensing method was developed for matrix metalloproteinase 2 (MMP-2). Ru(bpy)₃²⁺, gold nanoparticles (AuNPs) and Nafion were modified onto glassy carbon electrode (GCE) to form Ru(bpy)₃²⁺/AuNPs/Nafion/GCE as sensitive ECL platform and then ferrocene (Fc) labeled peptide was assembled onto the modified electrode to form ECL biosensing platform. The ECL intensity increased when the ECL biosensing electrode reacted with MMP-2 because of MMP-2-induced cleavage of Fc labeled peptide. The ECL method was applied to determine MMP-2 with detection limit of 0.3 ng/mL and one-step recognition, which is promising for point-of-care test of protease.     

碳纳米纤维糊电极电化学发光法测定甲硫哒嗪

制备了基于碳纳米纤维糊电极(CFPE)的新型电化学发光传感器.运用电化学方法对CFPE进行了表征,并考察了三联毗啶钉和甲硫哒嗪在此电极上的电化学行为和电化学发光行为.结果表明,该电极表现出很好的电化学活性和电化学发光响应.基于甲硫哒嗪对三联吡啶钉电化学发光的增强作用,建立了测定甲硫哒嗪的电化学发光新方法.实验考察了缓冲...     

玻碳电极上Ru（bpy）3^2＋的吸附及其电致化学发光的研究

通过电化学循环伏安法和电致化学发光方法,研究了Ru(bpy)32 在玻碳电极上的吸附,研究结果表明,2Ru(bpy)3 的浓度和与玻碳材料接触的时间,直接影响了Ru(bpy)32 在玻碳上的吸附.还考察了吸附的Ru(bpy)32 在玻碳电极上被氧化后脱附的情况.     

Electrochemiluminescence of tri(2,2′-bipyridine)ruthenium in aqueous solution on a gold-nanoparticle-modified glassy carbon electrode

The electrochemical behavior of electrochemical deposition of Au nanoparticles onto a glassy carbon electrode (GCE) and its application for the electrocatalytic electrogenerated chemiluminescence (ECL) of Ru(bpy)₃²⁺ in an aqueous solution without coreaction are investigated in this report. The modification of GCE by Au nanoparticles results in excellent catalysis of the ECL of Ru(bpy)₃²⁺. The effects of various factors, such as potential scan range, the presence of nitrogen and oxygen, and the scan rate on Ru(bpy)₃²⁺. ECL peaks, were systematically studied. This article has provided insight into the design of an Au-nanoparticle-modified electrode for ECL, analytical and catalytic applications. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 9, pp. 1127–1132. The text was submitted by the authors in English.     

玻碳电极上Ru(bpy)32+的吸附及其电致化学发光的研究

通过电化学循环伏安法和电致化学发光方法, 研究了Ru(bpy)₃²⁺在玻碳电极上的吸附, 研究结果表明, Ru(bpy)₃²⁺的浓度和与玻碳材料接触的时间, 直接影响了Ru(bpy)₃²⁺在玻碳上的吸附. 还考察了吸附的 在玻碳电极上被氧化后脱附的情况.     

A Sandwich‐type Electrochemiluminescence Aptasensor for Thrombin Based on Functional Co‐polymer Electrode Using Ru(bpy)32+ Doped Nanocomposites as Signal‐amplifying Tags

Herein, a signal‐on sandwich‐type electrochemiluminescence (ECL) aptasensor for the detection of thrombin (TB) was proposed. The graphene (GR) doped thionine (TH) was electropolymerized synchronously on the bare glassy carbon electrode (GCE) to form co‐polymer (PTG) electrode. The gold nanoparticles (AuNPs) were decorated on the surface of the PTG by in‐situ electrodeposition, and the functional co‐polymer (PTG‐AuNPs) electrode was utilized as sensing interface. Then, TB binding aptamer I (TBA I) as capture probes were modified on the PTG‐AuNPs electrode to capture TB, and Ru(bpy)₃²⁺/silver nanoparticles doped silica core‐shell nanocomposites‐labeled TB binding aptamer II (RuAg/SiO₂NPs@TBA II) were used as signal probes to further bind TB, resulting in a sandwich structure. With the assistant of silica shell and AgNPs, the enrichment and luminous efficiency of Ru(bpy)₃²⁺ were significantly improved. Under the synergy of PTG‐AuNPs and RuAg/SiO₂NPs, the ECL signal was dramatically increased. The proposed ECL aptasensor displayed a wide linear range from 2 fM to 2 pM with the detection limit of 1 fM, which is comparable or better than that in reported ECL aptasensors for TB using Ru(bpy)₃²⁺ and its derivatives as the luminescent substance. The excellent sensitivity makes the proposed aptasensor a promising potential in pharmaceutical and clinical analysis.     

Novel Designing of Chemically Modified Electrode (CME) of the Bio-MOF-1 for the Detection of Dopamine Based on Inhibition of [Ru(bpy)3]2+/DBAE System

Metal organic frameworks (MOFs) have attracted extensive attention in electrochemical research fields due to their high surface area and controlled porosity. Current study is design to investigate the ECL performance of the chemically modified electrode (CME) based on the bio-MOF-1, a porous zinc-adenine framework, which loaded ruthenium complex and employed for the detection of dopamine (DA). The composite material [Ru(bpy)₃]²⁺@bio-MOF-1 (Ru-bMOF) modified carbon glassy electrode (Ru-bMOF/GCE) exhibited an excellent ECL performance having a linear co-efficient response (R²=0.9968) for 2-(dibutyl amino) ethanol (DBAE), a classical ECL co-reactant was obtained over a concentration range of 1.0×10⁻⁹ M to 1.0×10⁻⁴ M in 0.10 M pH=6.0 phosphate buffer solution (PBS). Furthermore, DA was detected based on its inhibition effect on [Ru(bpy)₃]²⁺/DBAE system. Compared to traditional analytical methods, this method has various advantages such as simple electrode preparation, quick response, high reproducibility (RSD<2.0 %), low limit of detection (LOD=1.0×10⁻¹⁰ mol/L). This chemical investigated modified electrode had exploited potential for detection of DA.     

Potential controlling highly-efficient catalysis of wheat-like silver particles for electrochemiluminescence immunosensor labeled by nano-Pt@Ru and multi-sites biotin/streptavidin affinity

The potential controlling silver catalysis for Ru(bpy)(3)(2+) electrochemiluminescence (ECL) signal at a special potential -0.4～1.25 V was newly developed as the new ECL signal amplification strategy for ultrasensitive protein detection. Firstly, the wheat-like deposited silver (DpAg) particles were modified on the bare glass carbon electrode (GCE) surface by cyclic voltammetry deposition to capture the primary antibodies and then bind the antigen analytes. Secondly, as a sandwich immunoreaction format, the secondary antibodies conjugated with the Ru(bpy)(3)(2+)-doped Pt (Pt@Ru) nanoparticles by the multi-sites biotin/streptavidin (SA) affinity can be captured onto the electrode surface to generate ECL signal. In the proposed Ru(bpy)(3)(2+) ECL system without any co-reactant, the detected ECL signal was amplified due to following multiple amplification strategies: (1) the ECL catalysis for Ru(bpy)(3)(2+) was performed by electro-inducing the DpAg particles to generate Ag(+) ion and controlled by the special potential. The catalyzer Ag(+) was produced near the electrode surface and reproduced by cyclic potential scan, which improved the catalytic efficiency. (2) The amount of the ECL signal probes linked to secondary antibodies were amplified by the adsorption of Pt nanoparticles and the multiple sites bridge linkage of biotin/SA. These new multiple signal amplification strategies made the proposed ECL immunosensor achieve ultrasensitive detection for model protein human IgG with a detection limit down to 3 pg mL(-1), which can be further extended to the detection of disease biomarkers.