离子液体中异丁烷/2-丁烯烷基化反应机理研究

以复合离子液体[Et_3NH]Cl-AlCl_3-CuCl为催化剂,在连续搅拌釜式反应器中进行了异丁烷与2-丁烯烷基化反应;利用氘代异丁烷同位素示踪法研究了催化反应机理。结果表明,在离子液体中异丁烷烷基化的反应诱导期较短;三甲基戊烷产物主要源于异丁烷的自烷基化、丁烷/丁烯的直接烷基化以及C_(12)~+中间体的裂化反应,而大部分二甲基己烷是仲丁基碳正离子与丁烯加成的产物。     

固体超强酸（SO4^2-／ZrO2）的异丁烷／1-丁烯烷基化反应性能和失活研究

研究了固体超强酸(SO4^2-／ZrO2)催化剂的酸性及异丁烷-1-丁烯烷基化反应性能，结果表明，固体超强酸的酸性与焙烧温度有关，适当提高焙烧温度有利于样品酸强度的提高，但焙烧温度过高会导致脱硫，使样品酸强度和酸量降低，固体超强酸的异丁烷／1-丁烯烷基化催化反应活性与其酸性相对应，酸性强，反应活性高，但催化剂的活性衰减很快，这是催化剂表面的快速积炭所致。     

酸性离子液体催化的异丁烷/丁烯烷基化反应研究

以一系列酸性离子液体作为催化剂,考察了异丁烷/丁烯在不同离子液体中催化异丁烷与丁烯的烷基化反应,研究了离子液体在进行酸性和阴阳离子调整后对烷基化反应的影响.其中[MBSIM]OTf类离子液体催化所得目的产物三甲基戊烷含量最高可达69.8%,该类催化体系重复使用8次,催化性能没有明显下降.     

固体超强酸(SO24-/ZrO2)的异丁烷/1-丁烯烷基化反应性能和失活研究

研究了固体超强酸(SO24-/ZrO2)催化剂的酸性及异丁烷-1-丁烯烷基化反应性能, 结果表明, 固体超强酸的酸性与焙烧温度有关, 适当提高焙烧温度有利于样品酸强度的提高, 但焙烧温度过高会导致脱硫, 使样品酸强度和酸量降低. 固体超强酸的异丁烷/1-丁烯烷基化催化反应活性与其酸性相对应, 酸性强, 反应活性高, 但催化剂的活性衰减很快, 这是催化剂表面的快速积炭所致.     

异丁烷脱氢制异丁烯体系的热力学分析

对等温反应条件下的异丁烷脱氢制异丁烯反应进行了热力学分析,以获得等温反应条件下,压力和温度或其他反应条件与异丁烷脱氢反应的自由能ΔrG与热焓值ΔrH之间的关系。考察了不同反应条件(压力、温度和进料方式等)对于异丁烷脱氢反应的转化率的影响,为今后异丁烷脱氢制异丁烯工艺的开发提供热力学基础数据的支持。     

异丁烷-丁烯烷基化反应催化剂的研究

固体强酸;异丁烷-丁烯烷基化反应催化剂的研究     

异丁烷-丁烯在磷钨酸柱撑水滑石上的烷基化反应

层状化合物;异丁烷-丁烯在磷钨酸柱撑水滑石上的烷基化反应     

离子液体的酸性测定及其催化的异丁烷／丁烯烷基化反应

 初次采用吡啶红外光谱探针法测定了离子液体的酸性．该方法能鉴别离子液体的Br¨onsted／Lewis酸类型，并可以粗略指示离子液体的Lewis酸强度．将［bmim］Cl／AlCl3类离子液体用于催化异丁烷与丁烯的烷基化反应，考察了酸强度、反应温度、压力和时间对产物分布的影响，并在最优操作条件下与传统的H2SO4催化剂进行了比较．结果表明，离子液体对烷基化反应的催化活性和选择性与H2SO4可比，而且它更容易与产物分离，不经任何处理可循环利用10次．     

固体超强酸在异丁烷/丁烯烷基化反应中的再生研究

催化剂再生对于固体酸异丁烷／丁烯烷基化反应是必需的．虽然Broensted-Lewis共轭固体超强酸在温和条件下即对异丁烷／丁烯烷基化反应有良好的反应活性，但它仍象其它所有固体酸催化剂一样，面临着失活的问题．最主要的失活原因是积炭前身物生成并在催化剂表面的沉积，导致催化剂表面活性中心被覆盖．据此进行的再生方法研究集中在消除这些积炭前身物，本文中选择使用的是洗涤再生法，结果表明该方法对于该固体超强酸的再生在一定程度上是有效的。     

复合离子液体催化碳四烷基化反应性的研究

合成了一种新型的酸性离子液体催化剂——复合离子液体，该离子液体的阴离子具有双金属的配位中心。同时，研究了复合离子液体催化异丁烷与丁烯烷基化反应的规律。结果表明，在搅拌速率大于1500r/min，反应低于20℃，烃酸比2∶1~3∶1，烷烯比大于15，反应停留5min~10min，使用丁烯-2为碳四烯烃反应原料下，复合离子液体催化碳四烷基化所得烷基化油的研究法辛烷值（RON）最高可达100以上，明显优于常规氯铝酸离子液体催化所得烷基化油的质量。     

催化裂化干气与苯烷基化催化蒸馏制乙苯反应网络热力学研究

 高温气相反应条件下的催化裂化干气制乙苯过程中，容易生成甲苯和二甲苯等副产物；在该过程中采用催化蒸馏技术，使苯与乙烯在低温条件下进行反应，可大幅度降低产品中二甲苯的含量．通过对催化裂化干气与苯烷基化催化精馏过程中的各反应步骤进行分析与热力学计算，结合反应的实际产物组成，提出了苯与乙烯烷基化的反应网络，探讨了苯与乙烯烷基化反应过程中甲苯和二甲苯的形成机理及影响因素．结果表明，增大苯／乙烯比对提高乙烯平衡转化率及乙苯收率有利；在较低温度下进行烷基化反应，可大大减缓C－C键裂解速度，抑制甲苯和二甲苯生成，提高乙苯产品质量．     

The mechanism of the alkylation of isoxazolidin-3-one

In solvents of different polarities, the lactam-lactim tautomeric equilibrium of isoxazoli-din-3-one is strongly displaced in the direction of the lactam. The lactim form cannot be detected. It has been concluded that there is no connection between the dual chemical behavior of isoxazolidin-3-one and its potassium salt in the alkylation reaction with the equilibrium isomerization of these compounds. It has been shown that the mechanism of alkylation is connected with the structure of the lactam anion. Evidence is given in favor of a mesomeric structure of the anion with the main charge on the nitrogen at which substitution chiefly takes place.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 7, pp. 898–901, July, 1973.     

2-乙基己基膦酸单(2-乙基己基)酯(HEH[EHP])萃取稀土元素机理的研究Ⅰ.稀土元素(Ⅲ)在HNO3-H2O-HEH[EHP]体系中的分配及温度和溶剂效应

本文研究了HEH[EHP]的正己烷溶液在不同浓度(0—11M)的硝酸介质中萃取稀土元素(Ⅲ)的平衡规律。借助IR、NMR测定和斜率法研究了不同硝酸浓度下的萃取平衡反应,计算了不同萃取机理的浓度平衡常数。研究了温度和溶剂对萃取平衡的影响,测定了不同硝酸浓度和温度下各相邻元素对的分离因数,计算了萃取平衡反应的焓变值△H、相对自由能变化值△Z_z以及相对熵变值△S_z,并考察了这些热力学函数随原子序数的递变规律。     

Comparison of isotherms for the ion exchange of Pb(II) from aqueous solution onto homoionic clinoptilolite

The ion exchange equilibrium of Pb(II) on clinoptilolite modified with NH(4)Cl and NaCl can be represented by two types of isotherms. The first one is the ion exchange isotherm based upon the constant of thermodynamic equilibrium for the ion exchange reaction; however, the fitting procedure for this isotherm can be very tedious due to all the calculations involved and additional thermodynamic data. The second one is the Langmuir isotherm. The use of the Langmuir isotherm to represent ion exchange equilibrium has increased in recent last years since it adequately fits the equilibrium data and, furthermore, its calculation is much simpler. A comparison between the two isotherms showed that they fitted the experimental data reasonably well, but the Langmuir isotherm is much simpler and easier to use.     

金属溶剂萃取的热力学研究(Ⅶ)——2-乙基己基膦酸单(2-乙基己基)酯-硫酸钻-硫酸铜体系

本文提出了具有相同电荷的同号离子间作用力相等的假定, 简化了Pitzer的电解质溶液活度系数计算公式, 用此公式, 计算了H_2SO_4-CoSO_4-CuSO_4水相体系各单个离子活度系数以及水的渗透系数。本文还应用由作者提出的工作参考态法, 应用改进的Scatchard-Hildebrand模型计算了EHEHPA-CoSO_4-CuSO_4萃取体系中有机相各组分的活度系数以及萃取反应热力学平衡常数.     

ZnCl2温和有效地催化活泼亚甲基化合物与苄醇或烯丙醇的 直接烷基化反应

报道了ZnCl2催化的活泼亚甲基化合物和苄醇或烯丙醇的直接烷基化反应. 在无水ZnCl2 (5～10 mol%)的催化下, 以二氯甲烷为溶剂, 活泼亚甲基化合物和苄醇或烯丙醇进行直接烷基化反应以较高的收率得到活泼亚甲基化合物的烷基化产物, 反应后处理简单, 说明ZnCl2是一种温和有效的活泼亚甲基化合物和苄醇或烯丙醇进行直接烷基化的催化剂. 并对反应的机理进行了初步研究.     

Reaction and phase equilibria of esterification of isoamyl alcohol and acetic acid at 760 mm Hg

The thermodynamic behavior of esterification reaction equilibrium and vapor–liquid equilibrium (VLE) of acetic acid and isoamyl alcohol mixture and its products, isoamyl acetate and water were investigated in this study. The experiments of chemical and phase equilibria were conducted in an Othmer type equilibrium cell. Since this esterification reaction proceeds very slowly, thus, a commercial Y type zeolite, NaY catalyst, was added to accelerate reaction rate such that the reaction equilibrium will be reached sooner and before phase equilibrium is considered. Using experimental data and phase and reaction equilibrium equations, the reaction equilibrium constants were calculated at different temperatures. The experimental results showed that the reaction equilibrium constant was very slightly dependent on temperature. The experimental data were then correlated by the Wilson, NRTL, and UNIQUAC models with the consideration of association effect of acetic acid in vapor phase. The concept of transformation composition by Barbosa and Doherty [D. Barbosa, M.F. Doherty, 1987, Proc. R. Soc. London Ser. A 413, 443–459.] was applied to construct three-dimensional figures showing experimental data and the calculated composition surfaces. It is observed from figures that the reactive azeotropy described by Barbosa and Doherty does not exist for this quaternary mixture. This study provides the required thermodynamic information for the development and design of this esterification process.     

Computational Study on Thermodynamic Properties of Fischer-Tropsch Synthesis Process

Using the highly accurate G4 method, we computed the thermodynamic data of 1287 possible reaction products under a wide range of reaction conditions in the Fischer-Tropcsh synthesis (FTS) process. These accurate thermodynamic data provide basic thermodynamic quantities for the actual chemical engineering process and are useful in analyzing product distribution because FTS demonstrates many features of an equilibrium-controlled system. Our results show that the number of thermodynamically allowed products to increase when lowering temperature, raising pressure, and raising H₂/CO ratio. At low temperature, high pressure and high H₂/CO ratio, many products are thermodynamically allowed and the selectivity of product has to be controlled by kinetic factors. On the other hand, high selectivity of lighter products can be realized in thermodynamics by raising temperature and lowering pressure. We found that the equilibrium product yield will reach a maximum and remain unchanged when lowering temperature, raising pressure, and raising H₂/CO ratio to some limits, implying that optimizing reaction conditions has no effect on equilibrium product yields beyond these limits. The thermodynamic analysis is also useful in designing and evaluating FTS reaction mechanisms. We found that reaction pathways through formaldehyde should be discarded because of its extremely low equilibrium yield. Recently, in the FTS process using metal-oxide-zeolite catalysts for the highly selective production of C₂-C₄ olefins and aromatic hydrocarbons, there are several guesses on the possible reaction intermediates entering the zeolite channel. Our results show that ketene, methanol, and dimethyl ether are three possible reaction intermediates.     

关于弯曲界面气液两相相平衡化学势相等热力学判据的讨论

Thermodynamic criterion of equal chemical potential for phase equilibrium between gas and liquid in curved interface has been introduced in many textbooks and papers. In this paper, the process of the derivation of the criterion is proved to be wrong with analysis. In order to solve the problem, a proof procedure for the thermodynamic criterion of equal chemical potential is provided based on the definition of chemical potential. At the same time, a new thermodynamic criterion of two-phase equilibrium in curved interface is established using Gibbs interface thermodynamics and a new method for derivation of Kelvin equation is put forward based on the thermodynamic criterion of two-phase equilibrium. The new criterion which is derived directly from the second law of thermodynamics has a specific thermodynamic significance and clear physical model.