分子印迹壳聚糖/凹土分离富集-火焰原子吸收光谱测定痕量铅

建立了用分子印迹壳聚糖/凹凸棒石（MICA）分离富集-火焰原子吸收光谱（FAAS）测定痕量铅的新方法。 在动态吸附条件下,系统地研究了溶液pH值、流速、洗脱条件和干扰离子对痕量铅分离富集的影响;在pH=4.5,上样流速为0.60 mL/min的条件下,铅能被MICA定量富集;吸附的铅可用1.0 mol/L HCl-0.1 mol/L 甲基异丁酮的乙醇溶液在流速为0.96 mL/min条件下完全洗脱;在优化条件下,MICA对铅的动态吸附容量为36.78 mg/g。 线性范围为0～1.28 mg/L,r=0.999 7,检出限（3σ,n=11）为0.73 μg/L,相对标准偏差为1.69%(n=6,ρ=0.08 mg/L),回收率在98.7%～101.4%之间。 该方法操作简便、线性关系良好、灵敏度和精密度高,应用于实际水样中痕量铅的测定,结果满意。     

离子印迹壳聚糖/凹土分离富集-火焰原子吸收光谱测定中药材中痕量Cd(Ⅱ)的研究

建立了离子印迹壳聚糖/凹凸棒石(IICA)分离富集-火焰原子吸收光谱(FAAS)测定中药材中痕量Cd(Ⅱ)的新方法。在动态吸附条件下,系统研究了溶液pH值、流速、洗脱条件和干扰离子对痕量Cd(Ⅱ)分离富集的影响。研究表明,在pH为4.5,上样流速为0.60mL/min条件下,Cd(Ⅱ)能被IICA定量富集;吸附的Cd(Ⅱ)可用1.0mol/L HCl-0.1mol/L甲基异丁酮的乙醇溶液,在流速为0.96mL/min条件下完全洗脱。优化条件下,IICA对Cd(Ⅱ)的动态吸附容量为56.45mg/g。线性范围为0.00097～1.28mg/L,r=0.9994,检出限(3σ,n=11)为0.97μg/L,相对标准偏差为1.32%(n=6,c=0.08mg/L),回收率在96.5%～106.4%之间。该方法操作简便,灵敏度和精密度高,可应用于实际中药材样品中痕量镉的测定。     

蚕丝蛋白用于分离富集细胞色素c的研究

近年来,固相萃取被广泛用于蛋白质分离富集,萃取剂包括离子交换树脂~([1]),纳米材料~([2]),印迹材料~([3]).蚕丝是一种天然蛋白纤维~([4]),表面含氨基、醇羟基、酚羟基等官能团,是分离富集的有效载体.实验研究了蚕丝蛋白与血红素蛋白的相互作用,发现其对血红蛋白和细胞色素c表现完全不同的吸附,即在一定条件下血红蛋白不被吸附,而细胞色素c则被完全吸附.据此建立了选择性分离细胞色素c的新体系.     

印迹壳聚糖/凹土分离富集-FAAS测定水中痕量镉

建立了用离子印迹壳聚糖/凹土(ⅡGA)分离富集-火焰原子吸收光谱(FAAS)测定痕量镉的新方法.在动态吸附条件下,系统地研究了溶液pH值、流速、洗脱条件和干扰离子对痕量镉分离富集的影响;在pH4.5、上样流速为0.60 mL/min的条件下,镉能被ⅡCA定量富集;吸附的镉可用1.0 mol/L HCl-0.1 mol/...     

纳米SiO_2分离富集-火焰原子吸收法测定水中痕量银

研究了纳米SiO_2分离富集-火焰原子吸收法测定水中痕量银的新方法.考察了溶液pH、吸附时间、洗脱条件和干扰离子等因素对Ag~+分离富集的影响,确定了纳米SiO_2对Ag~+吸附的最佳条件.结果表明:在pH 4.1时,纳米SiO_2能定量吸附银,吸附在纳米SiO_2上的Ag~+可用0.5 mol/L HCl+0.5 mol/L硫脲定量洗脱.该法对银的检出限为0.77 ng/mL(3σ,n=11);线性范围为0.005～1.5μg/mL,对0.5μg/mL的Ag~+标液进行7次测定,RSD为3.6%,回收率在94.0%～101.5%之间;方法可用于环境水样中痕量银的测定.     

桑色素修饰的纳米TiO_2分离富集铬和铝

建立了在表面活性剂十二烷基硫酸钠(SLS)的活化作用下,桑色素修饰的纳米TiO2分离富集,电感耦合等离子体原子发射光谱(ICP-AES)测定Cr3+和A l3+的新方法。考察了溶液pH、洗脱条件和干扰离子等因素对分析物分离富集的影响。结果表明,在pH 3.0时,Cr3+和A l3+可被桑色素修饰的纳米TiO2定量富集,吸附的金属离子可用1.5 mL 0.50 mol/L HC l溶液完全洗脱。在优化的实验条件下,纳米TiO2-桑色素对Cr3+和A l3+的吸附容量分别为9.69 mg/g和12.76 mg/g。本法对Cr3+和A l3+的检出限(3σ)分别为:0.21和0.49 ng/mL,相对标准偏差(RSD)分别为2.2%和1.6%(n=11,C=50 ng/mL)。本法应用于藏药和扇贝标准样品(GBW 10024)中Cr3+和A l3+的测定,测定值与标准值基本吻合,分析结果满意。     

纳米TiO2微柱分离富集测定环境样品中的微量碲

以处理过的纳米TiO2为微柱吸附材料,采用流动注射技术进行微量碲的分离富集,探讨了溶液的pH值、试样流速、试样体积、洗脱液浓度和用量以及干扰离子等因素的影响。 实验结果表明,pH值在8～9.5范围内,纳米TiO2对Te(Ⅳ)具有良好的吸附性能,吸附率接近99%,动态饱和吸附容量为37.02 mg/g;选用2 mL 0.5 mol/L NaOH溶液可将吸附的Te(Ⅳ)完全洗脱,富集倍数为30。 本法的检出限(3σ)为0.013 mg/L,相对标准偏差为RSD=1.99%。 将本法应用于水样的分析,碲的回收率在98%~103%之间,结果令人满意。     

硫代乙酰胺键合硅胶在线选择性固相萃取火焰原子吸收测定环境样品中痕量铜

以制备的硫代乙酰胺键合硅胶为微柱填充材料,建立酸性条件(pH 1 0)下流动注射微柱选择性预富集,0.6 mol/L硫脲溶液洗脱,火焰原子吸收测定环境样品中痕量铜的方法。流动注射在线固相萃取的最佳采样流速为8.0 mL/min;最佳洗脱流速为5.0 mL/min,时间为60 s。在优化的条件下,采样体积为10和50 mL时,线性范围分别为2.0～100.0μg/L和0.5～30.0μg/L;检出限(3σ)分别为0.36和0.07μg/L;富集倍数分别为80和170;相对标准偏差分别为(n=9)3.5%和2.0%。研究了环境样品中常见阴阳离子对测定的干扰。应用于灌木枝叶样品(GBW07602)、标准模拟水样(GBW08608)样品和环境样品中铜的分离与富集,取得满意结果。     

介孔TiO2分离富集-火焰原子吸收法测定矿样中痕量Cd(Ⅱ)

研究了介孔Ti O2分离富集材料的制备及其对Cd(Ⅱ)的吸附性能,考察了影响吸附和解吸的主要因素。pH=6.0时,介孔Ti O2能定量吸附溶液中的痕量Cd(Ⅱ),其静态饱和吸附容量为57.8 mg/g。吸附在介孔Ti O2上的Cd(Ⅱ)可用1 mol/L HCl洗脱,洗脱液中的Cd(Ⅱ)用火焰原子吸收法测定。本法对Cd(Ⅱ)的检出限(3σ)为23.3 ng/mL,相对标准偏差(RSD)为2.0%(n=7,c=1.0μg/mL),回收率在94.0%～102.5%之间。该方法用于矿样中痕量Cd(Ⅱ)的测定,结果满意。     

纳米TiO2微柱分离富集测定环境样品中的微量硒

以处理过的纳米TiO2为微柱吸附材料,采用流动注射技术进行微量硒的分离富集,考察了纳米TiO2微柱对Se(IV)的吸附性能,探讨了溶液的pH值、试样流速、试样体积、洗脱液浓度和用量以及干扰离子等因素的影响。实验结果表明,pH在1～6范围内,试样流速为0.5 mL/min,纳米TiO2对Se(IV)具有良好的吸附性能,吸附率可达97%,动态饱和吸附容量为7.92 mg/g;选用1 mL 0.1 mol/L NaOH溶液可将吸附的Se(IV)完全洗脱,富集倍数为40。本法的检出限(3σ)为0.13 mg/L,相对标准偏差为1.56 %。将本法应用于国家标准样品GBW07280的分析,测定值与参考值一致。     

Structure and structural changes of the silk fibroin from Samia cynthia ricini using nuclear magnetic resonance spectroscopy

The structure of silk fibroin from a wild silkworm, S. c. ricini, the amino acid sequence of which consists of repeated poly-Ala and Gly-rich regions, was examined by using solution and solid-state NMR methods. The structural transition of the silk fibroin in aqueous solution was monitored by using 13C solution NMR spectroscopy as a function of temperature. The fast exchange with respect to the chemical shift between the helix and coil conformations was observed in the poly-Ala region and the slow conformational change from alpha-helix to random coil was observed for the Gly residue adjacent to the N-terminal Ala residue of the poly-Ala region. The torsion angles of several Ala and Gly residues in the model peptide, GGAGGGYGGDGG(A)12GGA-GDGYGAG, were determined by the conformation-dependent 13C chemical shifts, rotational echo double resonance (REDOR) and 2D spin-diffusion NMR methods. The solid-state NMR analysis leads to the precise silk structure before spinning, where the poly-Ala sequence takes a typical alpha-helix pattern with a tightly winded helical structure at both terminal regions of the poly-Ala sequence. This is expected to stabilize the alpha-helical structure of the poly-Ala region in S. c. ricini silk fibroin from the silkworm.     

Rheological behavior of cellulose/silk fibroin blend solutions with ionic liquid as solvent

The rheological behavior of cellulose and silk fibroin blend in 1-butyl-3-methylimidazolium chloride was studied. The data from the rheological results was analyzed to understand the microstructure of the blend solutions. The viscosity and dynamic modulus of the blend solution decreased with increasing ratio of silk fibroin. While comparing the experimental results with the calculated data from the log-additivity rule, it is revealed that zero-shear viscosity, dynamic modulus show positive–negative deviations and a typical continuous–discrete type of morphology could be imaged. At lower shear rate, the change of phase morphology took place at the ratio of about 0.5 volume fraction of cellulose. However, the blend solution showed positive deviations for all cellulose/silk fibroin blend ratios at high shear rate, which indicates that the dispersion of cellulose and silk fibroin was improved under shear stress. The properties of cellulose/silk fibroin blends observed by Fourier transform infrared spectroscopy and scanning electron microcopy agreed with the result from rheology.     

Silk fibroin solution properties related to assembly and structure

The impact of physiological factors on silk fibroin solution properties was studied. Specifically, the impact of fibroin concentration, protein purity, cation type and concentration, and pH on aqueous solution viscosity, shear behavior, and surface tension were assessed in the context of silk protein assembly. The results demonstrate that in vitro results could be correlated to in vivo processing events during silk spinning. Rheological properties with reference to the amphiphilic block structure of the protein are described, pH dependency of shear response was quantitatively correlated to the predicted pI values of the fibroin protein, and cooperativity among environmental factors such as pH and salts was identified. Stabilization of silk fibroin solution states by calcium was identified as a mode to control shear sensitivity of the fibroin solution. The cooperativities identified suggest tight control of fibroin aqueous solution rheological properties to gain a window of protection against premature crystallization of the fibroin during processing, assuring safe storage, transport, and finally successful fiber spinning.     

蚕腺体内和再生丝素蛋白水溶液的性能研究

用偏光显微镜观察了蚕腺体内和再生丝素蛋白水溶液的流动状态和各向异性现象,用乌氏粘度计测试了其流出时间,并用HAKKE流变仪测试了其粘度。结果发现蚕腺体内和再生丝素蛋白水溶液的性质差别非常大,认为丝素蛋白水溶液在蚕腺体内存在一个逐步熟成的过程。随着丝素蛋白水溶液在腺体内的前移,丝素蛋白分子逐渐沿移动方向取向而呈有序态,最终成为粘度非常大的各向异性的凝胶体,而再生丝素蛋白水溶液是粘度非常低的各向同性溶液。这些差异表明,丝素蛋白水溶液在蚕腺体内的熟成过程是蚕能够吐出优良蚕丝的关键步骤,要想制备出高性能的纤维,在“仿生纺丝”之前,首先要“仿生制备纺丝液”。     

羧甲基丝素的制备工艺优化及其乳化性能

以废丝为主要原料,将不溶于水的丝素蛋白通过与一氯乙酸在乙醇溶剂中的醚化反应,合成了可溶性的羧甲基丝素。讨论了几种主要因素(如碱化时间、碱化温度、醚化时间和醚化温度等)对产物醚化度的影响,得到了制备羧甲基丝素的醚化工艺条件:碱化时间90 min、醚化时间90 min、碱化温度25℃、醚化温度70℃。所得羧甲基丝素的醚化度为0.7425。测定羧甲基丝素的表面活性后,得到羧甲基丝素的临界胶束浓度为1.25 g/L,亲水亲油平衡(HLB)值为10。丝素蛋白溶液具有一定的起泡能力,且在质量分数为1.0%～1.2%范围内的稳定性较好,但不宜作发泡剂。丝素蛋白溶液具有良好的乳化能力和乳化稳定性,可作为良好的乳化剂。     

丝素纳米颗粒的制备及应用于L-天冬酰胺酶的固定化

丝素蛋白纤维溶于高浓度中性盐溴化锂溶液或氯化钙-乙醇-水三元溶剂中, 经过透析和纯化可以制成3种液态丝素. SDS-PAGE分析结果表明, 其分子量分布范围明显不同. 应用能与水混溶的有机溶剂如丙酮等可将这种丝素制成丝素纳米颗粒, 用SEM观察到丝素纳米颗粒粒径分布范围为50~120 nm. 以戊二醛为交联剂, 将治疗急性淋巴性白血病常用酶制剂L-天冬酰胺酶共价结合在丝素纳米颗粒上. 酶活性分析结果表明, 由肽链断裂较少的丝素制备的纳米颗粒更适合于酶的生物结合. 酶动力学研究结果表明, 这种固定化酶活性回收率为44%, 热稳定性较游离酶有明显提高, 最适pH值范围加宽为6.0~8.0, 最适反应温度提高10 ℃; 抗胰蛋白酶水解能力明显增强. 结果表明, 丝素纳米颗粒与丝素蛋白膜一样, 是一种酶固定化的良好载体, 在药物缓释系统方面具有潜在的研究和开发价值.     

手控注射分离器分离富集火焰原子吸收测定蔬菜中的铅

手控注射分离器分离富集火焰原子吸收测定蔬菜中的铅;     

Determination of Trace Lithium in Uranium Compounds by Adsorption on Activated Alumina Using a Micro-column Method

A novel method using a micro-column packed with active alumina as solid phase was proposed for separation of trace lithium from uranium compounds prior to determination. The method is based on a preliminary chromatographic separation of the total amount of uranium. This separation involves passing the solution containing sodium carbonate through active alumina and then eluting the trace lithium retained by the solid phase with a solution of sulfuric acid. Two modes, off-line and on-line micro-column preconcentration, were performed. In conjunction with atomic absorption spectrometry, this on-line preconcentration technique allows a determination of lithium at 10(-9) level. Both off-line and on-line mode operation conditions were investigated in separation and determination of trace lithium by micro-column method (length of column bed, flow rate, etc.). The adsorption capacity of activated alumina was found to be 343 microg g(-1) for lithium. Under the optimal operation condition, the detection limit (DL) of on-line preconcentration corresponding to three times the standard deviation of the blank (S/N = 3) was found to be 1.3 ng mL(-1) and the RSD of this method is 3.32% (n = 5). The on-line calibration graph was linear over the range 20 - 200 ng mL(-1). A good preconcentration factor 820 was achieved by experiment under the on-line mode. The developed method was applied to the analysis of trace lithium in nuclear grade uranium compounds.     

QUENCHING OF PHOTOEXCITED 4,4'-DICARBOXY-2,2'-BIPYRIDINEBIS(2,2'-BIPYRIDINE)RUTHENIUM(II) BY OXYGEN IN AQUEOUS SOLUTION AND IN SILK FIBROIN MEMBRANE

Abstract— Photoluminescence and quenching of 4,4'-dicarboxy-2,2'-bipyridinebis(2,2'-bipyridine)-ruthenium(II) complex (Ru(DCbpy)(bpy)²₂⁺) in an aqueous solution as well as in a silk fibroin membrane were studied. Emission quenching by oxygen in an aqueous solution showed a linear relationship with respect to oxygen concentration. When the complex was incorporated into a silk fibroin membrane by adsorption from an aqueous solution into a preformed membrane, the photoexcited state of the complex was not quenched by oxygen in an aqueous phase. However, when the complex was incorporated into a silk fibroin membrane by casting a mixture of the complex and silk fibroin, the photoexcited complex was quenched by oxygen in an aqueous phase. In this case the Stern-Volmer plots showed a downward-deviating curve indicating heterogeneity of the probe site. Emission intensity decreased with an increase of the water content in the silk fibroin membrane.     

Miscibility and biodegradability of silk fibroin/carboxymethyl chitin blend films

Blend films of silk fibroin and carboxymethyl chitin were prepared by solution casting using water as a cosolvent. The blend films were subjected to post-treatment with an aqueous methanol solution to induce beta-sheet formation of silk fibroin. The miscibility of the blend films both before and after methanol treatments was investigated in terms of chemical interactions, morphologies, thermal properties, and crystal structures by using FTIR spectroscopy, SEM, DSC, and XRD. The results indicate that the blend between silk fibroin and CM-chitin was semi-miscible because only the amorphous parts of the polymers were compatible with each other. The enzymatic degradation showed that the incorporation of CM-chitin enhanced biodegradability and swelling ability of silk fibroin.