氧化锌纳米棒/云母复合粉体的合成、表征及红外发射性能

采用液相沉积法制备了氧化锌(ZnO)纳米棒负载云母复合粉体,其合成工艺分为:(1)云母粉体表面沉积ZnO纳米粒子,并经煅烧制得表面晶种化的云母粉体;(2)以七水硫酸锌(ZnSO4·7H2O)为前驱体,乙醇胺和氨水为络合剂,制得液相沉积前驱体溶液,并在晶种化的云母粉体表面沉积ZnO纳米棒。利用X-射线衍射(XRD)、ζ电位仪、扫描电子显微镜(SEM)以及红外发射率测试仪对氧化锌/云母复合粉体进行了测试与表征。结果表明,云母分散于乙醇水体积比为1∶1的混合溶液中,其表面带负电(-37 mV),而ZnO粒子表面则带正电(16 mV);两种粒子混合时,可通过静电引力实现ZnO纳米粒子在云母表面沉积;随着云母表面ZnO纳米棒沉积密度的增大,复合粉体在8~14μm波段内的红外发射率逐渐增大,从0.800增加至0.863;对比棒状ZnO球体,结构单元聚集状态的变化对最终红外发射性能的影响不大。     

SiO2/ZnO复合纳米粒子的制备及表征

采用双注控制沉积法(Controlled Double-Jet Precipitation,CDJP)将反应物添加到含有SiO₂的溶液中,通过直接的表面反应来制备单分散的SiO₂/ZnO复合纳米粒子,并对其进行了表征。透射电镜(TEM)观察表明,SiO₂表面有一层ZnO纳米颗粒或薄层。对复合纳米粒子SiO₂/ZnO进行X射线衍射(XRD)分析,复合颗粒的衍射峰与单独的氧化锌的衍射峰完全一致。能量弥散X射线法(EDX)分析表明,复合颗粒中含有Zn、Si、O元素。荧光光谱表明有ZnO的吸收峰。     

氧化锌纳米棒微结构光电极的制备

通过两步法,即首先热分解醋酸锌制备氧化锌晶种层,在晶种的诱导下,再采用低温水热法在氟掺杂的SnO₂导电玻璃(fluorine-doped tin oxide, FTO)基底导电面上成功制备出高取向性的氧化锌纳米棒阵列光电极。系统研究了前驱液浓度、溶液pH值、反应时间等实验条件对光电极微结构的影响。实验结果表明在一定变化范围内,随着前驱液浓度和溶液pH值的增大,纳米棒的直径增大;随着反应时间的延长,纳米棒的长度增长。将氧化锌纳米棒阵列薄膜制作成染料敏化太阳电池(dye-sensitized solar cell, DSSC)的光电极,并对电池的I-V特性进行了表征。     

在一维ZnO表面可控构建Co3Mn1纳米晶及其催化CO氧化性能

利用热分解法制备了结构明确的负载型纳米晶催化剂。在纳米晶成核和生长过程中加入一维ZnO纳米棒作为晶种,调控不同组分的纳米晶在 ZnO纳米棒表面均匀生长,从而获得了结构明确的 MnO/ZnO、Co₃O₄/ZnO、Co₃Mn₁/ZnO催化剂。透射电子显微镜(TEM)与 X 射线粉末衍射(XRD)结果显示,不同组分纳米颗粒都均匀分散在 ZnO 纳米棒表面。相对于 MnO/ZnO 和Co₃O₄/ZnO催化剂,Co₃Mn₁/ZnO催化剂在CO氧化反应中具有最佳的催化性能。在200 L·g_cat^-1·h^-1的气时空速下,Co₃Mn₁/ZnO催化剂起活温度为 50 ℃,其 T100(CO 转化率达到 100% 时的温度)为 200 ℃;利用 X 射线光电子能谱(XPS)对不同催化剂进行了分析,结果显示,Co₃Mn₁/ZnO催化剂的氧空位比MnO/ZnO催化剂提高了30%以上,从而使其具有较高的CO氧化催化性能。更为重要的是,Co₃Mn₁/ZnO复合纳米晶催化剂的活化能(39.4 kJ·mol^-1)远低于其它负载型纳米晶催化剂。     

In2O3敏化ZnO纳米棒阵列的性能及其光电催化活性

以掺氟SnO₂ (FTO)导电玻璃为基底, 采用水热法制备了ZnO纳米棒阵列. 通过In(NO₃)₃水溶液水洗的方法, 合成了In₂O₃敏化ZnO纳米棒阵列光催化剂. 采用场发射扫描电子显微镜(FESEM), X射线能谱(EDX), X射线衍射(XRD)及紫外-可见漫反射光谱(UV-Vis DRS)对样品的形貌、结构、组成、晶相等进行一系列的表征. 以罗丹明B (RhB)为目标降解物, 探究了In₂O₃敏化ZnO 纳米棒阵列光电催化活性. 采用场诱导表面光伏技术(FISPV)研究了不同含量的In₂O₃敏化ZnO纳米棒阵列在光照射下的光生电荷行为. 结合电化学工作站检测不同样品的光电流, 随着In₂O₃敏化量的改变, 光电流和开路电压也随之改变. 并探讨了In₂O₃敏化ZnO纳米棒阵列光生电荷行为与光电催化活性之间的关系. 结果表明, 适量In₂O₃敏化的ZnO光催化剂在可见光下2 h内对罗丹明B的降解效率达到95%, 是单纯ZnO纳米棒阵列的2.4倍.     

纳米三氧化钨修饰碳纳米管载铂催化剂对甲醇氧化的电催化性能

采用表面修饰技术将碳纳米管(CNT)表面羧基化, 通过羧基将钨离子基团修饰到碳纳米管的外表面, 再通过高温焙烧处理将钨离子基团氧化成WO₃, 成功合成了纳米WO₃/CNT复合物, 进一步还原Pt 的前驱体而得到Pt-WO₃/CNT复合催化剂. 采用X射线粉末衍射(XRD)和透射电镜(TEM)对样品的形貌和晶型结构进行了表征, 结果表明, Pt纳米粒子为面心立方晶体结构, 均匀地分布在WO₃修饰的碳纳米管表面. 采用循环伏安(CV)和计时电流法研究了在酸性溶液中Pt-WO₃/CNT催化剂对甲醇的电催化氧化活性, 结果表明WO₃修饰的碳纳米管载铂催化剂比用混酸处理的碳纳米管载铂催化剂对甲醇呈现出更高的电催化氧化活性和更好的稳定性.     

温和条件下制备形貌可控的羟基磷灰石

在温和条件下采用简单的实验方法成功制备出不同结构和形貌的羟基磷灰石(HAP)纳米粒子。采用沉淀-水解两步法,以PEG和PVP为表面活性剂,在沉淀步骤制备出前驱体CaHPO₄粒子,然后在100℃、常压条件下水解获得高结晶度的HAP纳米棒。采用PEG制备的纳米棒形貌均匀、纵横比高;采用PVP制备的纳米棒尺寸范围较宽且尺寸较小。直接采用一步沉淀法也能够成功制备出HAP纳米粒子。采用PEG制备出麦穗状的纳米粒子;采用PVP制备出尺寸小的纳米棒和纳米粒子混合物。HAP纳米晶的结构和形貌因制备条件不同发生很大变化,故而控制其合成,有望用于生物医药领域。     

新型磁性荧光Fe3O4-CdSe纳米复合材料的制备

以1-十八烯作为高沸点溶剂, 在磁性粒子表面沉积量子点获得新型的磁性荧光Fe₃O₄-CdSe 纳米异质结构. 首先以乙酰丙酮铁(Fe(acac)₃)为前驱体, 二苯醚为溶剂, 油酸为表面活性剂和油胺(OAm)为表面活性剂兼还原剂, 通过溶剂热法制备单分散性的Fe₃O₄ 纳米粒子. 然后以1-十八烯为高沸点溶剂, CdO 为镉源,TOP-Se为硒源, 十六胺为表面活性剂以及硬脂酸为生长促进剂和成核剂制备得到新型的Fe₃O₄-CdSe纳米异质结构. 通过透射电镜(TEM), 傅里叶变换红外(FTIR)光谱, X射线衍射(XRD)谱, X射线光电子能谱(XPS)分析仪, 振动样品磁强计(VSM), 紫外-可见(UV-Vis)光谱和光致发光(PL)等手段对Fe₃O₄-CdSe 纳米复合材料的结构和性能进行表征. 结果表明, CdSe纳米粒子成功地吸附在Fe₃O₄纳米粒子表面, 并沿着c轴生长, 形成了宽3.6 nm, 长分别为14.5 和32.5 nm的新型枣核状和钉子状的异质结构体. 这种新型的Fe₃O₄-CdSe纳米复合材料是由磁铁矿Fe₃O₄和六方形的CdSe棒状结构组成, 具有较好的荧光性能和超顺磁性. 随着CdSe棒长度的增加, 荧光吸收峰向长波方向移动. Fe₃O₄纳米粒子, 枣核状和钉子状的Fe₃O₄-CdSe纳米复合材料的饱和磁化强度分别是57.80, 40.76和31.10 emu·g^-1.     

Co3O4/ZnO修饰针灸针的制备及其在葡萄糖检测领域的应用

将Co₃O₄/ZnO针状纳米棒材料修饰到针灸针表面用于检测葡萄糖浓度的变化。首先采用水热法在针灸针表面得到 Co（CO₃）_0.5（OH）·0.11H₂O针状纳米棒前驱体,然后在500 ℃条件下退火3 h得到Co₃O₄针状纳米棒阵列。再采用浸渍法将预制备好的ZnO量子点修饰到Co₃O₄针状纳米棒表面,得到Co₃O₄/ZnO复合修饰的针灸针。研究发现此针灸针对葡萄糖具有较好的电流响应（2 264.27 μA·L·mmol^-1·cm^-2）、较快的响应速度（<4 s）及较低的检测极限（0.311 μmol·L^-1（S/N=3））。且该针灸针在用于检测人体模拟细胞液中葡萄糖浓度时,对抗坏血酸和尿素等表现出较强的抗干扰性。     

Co3O4/ZnO修饰针灸针的制备及其在葡萄糖检测领域的应用

将Co₃O₄/ZnO针状纳米棒材料修饰到针灸针表面用于检测葡萄糖浓度的变化。首先采用水热法在针灸针表面得到Co（CO₃）_0.5（OH）·0.11H₂O针状纳米棒前驱体,然后在500 ℃条件下退火3 h得到Co₃O₄针状纳米棒阵列。再采用浸渍法将预制备好的ZnO量子点修饰到Co₃O₄针状纳米棒表面,得到Co₃O₄/ZnO复合修饰的针灸针。研究发现此针灸针对葡萄糖具有较好的电流响应（2 264.27 μA·L·mmol^-1·cm^-2）、较快的响应速度（<4 s）及较低的检测极限（0.311 μmol·L^-1（S/N=3））。且该针灸针在用于检测人体模拟细胞液中葡萄糖浓度时,对抗坏血酸和尿素等表现出较强的抗干扰性。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.