阴极催化剂Sm1.5Sr0.5MO4 (M＝Ni, Co, Fe)在低温常压下合成氨

利用溶胶—凝胶法制备了复合氧化物Sm1.5Sr0.5MO4 (M＝Ni, Co, Fe)(SSM),并利用XRD和SEM等对样品进行表征。用Nafion膜作电解质、以SSM作为阴极、Ni-SDC金属陶瓷为阳极、银-铂网做集流体组成单电池,在温度为25℃～100℃的低温常压下以干燥氮气和湿的氢气为原料进行电化学合成氨气测定,同时研究了影响氨合成的关键因素,确定了合适的工作温度,实验结果表明,最高氨产率可达到1.05×10-8mol·s-1·cm-2。     

Electrical Properties of Sm‐doped Ceria (SDC) and SDC Carbonate Composite

This study prepared a dense Sm‐doped ceria (SDC) and an SDC carbonate composite (abbreviated as SDC‐C). The latter was prepared by immersing porous SDC with a formula of (Ce_0.8Sm_0.2)O_1.9 and a relative density of approximately 65‐70% into a molten mixture of carbonates containing 1:1 molar ratio of Li₂CO₃ and Na₂CO₃ at 500 °C. The relative density of the SDC‐C was close to 100%. In addition, SDC oxide without carbonates, which also has a relative density of close to 100%, was heat treated at 1600 °C. At 500 °C, the electrical conductivity and ionic transference number (t_i) of the SDC oxide were 1.79(5) × 10^?3 S·cm^?1 and 0.99(2), respectively, such that electronic conduction could be disregarded. Increasing the temperature caused a gradual decrease in the t_i of SDC. Following the addition of carbonates to SDC, the electrical conductivity reached 1.23(9) × 10^?1 S·cm^?1 at 500 °C. After 14 days (340 h), the electrical conductivity of the SDC‐C at 490 °C, leveled off at about 6 × 10^?2 S·cm^?1. SDC‐C could be used as a potential electrolyte in solid oxide fuel cells (SOFCs) at temperatures below 500 °C.     

Electrochemical synthesis of ammonia using a cell with a Nafion membrane and SmFe0.7Cu0.3?xNixO3 (x = 0?0.3) cathode at atmospheric pressure and lower temperature

Samaria-doped ceria Ce_0.8Sm_0.2O_2−δ (SDC) and SmFe_0.7Cu_0.3−x Ni _x O₃ have been synthesized by the sol-gel method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The electrochemical synthesis of ammonia was investigated at atmospheric pressure and low temperature, using the SFCN materials as the cathode, a Nafion membrane as the electrolyte, nickel-doped SDC (Ni-SDC) as the anode and silver-platinum paste as the current collector. Ammonia was synthesized from 25 to 100°C when the SFCN materials were used as cathode, with SmFe_0.7Cu_0.1Ni_0.2O₃ giving the highest rates of ammonia formation. The maximum rate of evolution of ammonia was 1.13 × 10⁻⁸ mol·cm⁻²·s⁻¹ at 80°C, and the current efficiency reached as high as 90.4%. Supported by the National Natural Science Foundation of China (Grant No. 20863007)     

Synthesis and Characterization of Sulfonated Polyimides Containing Trifluoromethyl Groups as Proton Exchange Membranes

A novel sulfonated diamine, 4,4′‐bis(4‐amino‐3‐trifluoromethylphenoxy) biphenyl 3,3′‐disulfonic acid (F‐BAPBDS), was successfully synthesized by nucleophilic aromatic substitution of 4,4′‐dihydroxybiphenyl with 2‐chloro‐5‐nitrobenzotrifluoride, followed by reduction and sulfonation. A series of sulfonated polyimides of high molecular weight (SPI‐x, x represents the molar percentage of the sulfonated monomer) were prepared by copolymerization of 1,4,5,8‐naphathlenetetracarboxylic dianhydride (NTDA) with F‐BAPBDS and nonsulfonated diamine. Flexible and tough membranes of high mechanical strength were obtained by solution casting and the electrolyte properties of the polymers were intensively investigated. The copolymer membranes exhibited excellent oxidative stability due to the introducing of the CF₃ groups. The SPI membranes displayed desirable proton conductivity (0.52×10⁻¹–0.97×10⁻¹ S·cm⁻¹) and low methanol permeability (less than 2.8×10⁻⁷ cm²·s⁻¹). The highest proton conductivity (1.89×10⁻¹ S·cm⁻¹) was obtained for the SPI‐90 membrane at 80°C, with an IEC of 2.12 mequiv/g. This value is higher than that of Nafion 117 (1.7×10⁻¹ S·cm⁻¹). Furthermore, the hydrolytic stability of the obtained SPIs is better than the BDSA and ODADS based SPIs due to the hydrophobic CF₃ groups which protect the imide ring from being attacked by water molecules, in spite of its strong electron‐withdrawing behaviors.     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Enhancing proton conductivity of proton exchange membrane with SPES nanofibers containing porous organic cage

Effective proton conducting sites and establishing proton channels are two critical factors in developing high‐performance proton exchange membranes. This study first establishes a strategy in designing effective proton conducting channels for Nafion by using solution blowing of sulfonated polyethersulfone (SPES) nanofibers containing CC3, which is an emerging porous organic cage that possesses the advantages of dissolvable organic solvents and high proton conduction from its interconnected three‐dimensional pore structure. Our strategy results in SPES nanofiber networks with CC3 uniformly involved in and composite membranes with Nafion‐filled interfiber voids. Benefiting from such structural features, the composite membrane exhibits high proton conductivity (0.315 S cm^?1 at 80°C and 100% RH), low methanol permeability (0.69 × 10^?7 cm² S^?1), excellent water absorption, thermal and dimensional stability, and single‐cell performance. This study provides not only a valuable reference for the application of CC3 but also a new idea for establishment of proton transfer channels.     

Novel sulfonated polyimide/ZrO2 composite membrane as a separator of vanadium redox flow battery

Sulfonated polyimide (SPI) and ZrO₂ are blended to prepare a series of novel SPI/ZrO₂ composite membranes for vanadium redox flow battery (VRFB) application. Results of atomic force microscopy and X‐ray diffraction reveal that ZrO₂ is successfully composited with SPI. All SPI/ZrO₂ membranes possess high proton conductivity (2.96–3.72 × 10^?2 S cm^?1) and low VO²⁺ permeability (2.18–4.04 × 10^?7 cm² min^?1). SPI/ZrO₂‐15% membrane is determined as the optimum one on account of its higher proton selectivity and improved chemical stability. The VRFB with SPI/ZrO₂‐15% membrane presents higher coulombic efficiency and energy efficiency than that with Nafion 117 membrane at the current density, which ranged from 20 to 80 mA cm^?2. Cycling tests indicate that the SPI/ZrO₂‐15% membrane has good operation stability in the VRFB system. Copyright © 2014 John Wiley & Sons, Ltd.     

Ozone reduction at Nafion modified Au electrode and the measurement of ozone concentration in highly resistive solutions

The mass transport and charge transfer kinetics of ozone reduction at Nafion coated Au electrodes were studied in 0.5 mol/L H2SO4 and highly resistive solutions such as distilled water and tap water. The diffusion coefficient and partition coefficient of ozone in Nafion coating are 1.78×10-6 cm2·s-1 and 2.75 at 25℃ (based on dry state thickness), respectively. The heterogeneous rate constants and Tafel slopes for ozone reduction at bare Au are 4.1×10-6 cm·s-1, 1.0×10-6 cm·s-1 and 181 mV, 207 mV in 0.5 mol/L H2SO4 and distilled water respectively and the corresponding values for Nafion coated Au are 5.5×10-6 cm·s-1, 1.1×10-6 cm·s-1 and 182 mV, 168 mV respectively. The Au microelectrode with 3 μm Nafion coating shows good linearity over the range 0-10 mmol/L ozone in distilled water with sensitivity 61 μA·ppm-1 ·cm-2, detection limit 10 ppb and 95% response time below 5 s at 25℃. The temperature coefficient in range of 11-30℃ is 1.3%.     

Synthesis and Characterization of Phenolphthalein‐Containing Sulfonated Poly(arylene ether phosphine oxide)s by Direct Polycondensation for Proton Exchange Membrane

A series of novel phenolphthalein‐containing sulfonated poly(arylene ether phosphine oxide)s (sPAEPP) with various sulfonation degrees were synthesized by direct polycondensation. The structure of sPAEPP was confirmed by ¹H‐NMR, ¹³C‐NMR, and IR spectroscopy. The high‐molecular weight of these polymers was determined by gel permeation chromatography (GPC). The transparent, tough, and flexible membranes could be achieved by solution casting. The macroscopic properties and microstructure of the obtained membranes were investigated in detail. The results showed that these sPAEPP membranes displayed excellent properties in terms of swelling, proton conductivity, and methanol permeability. For example, sPAEPP‐100 membrane exhibited an appropriate water uptake of 33.1%, a swelling ratio of only 11.7% (lower than 20.1% of Nafion 117), a proton conductivity of 0.11 S cm^?1 (similar to that of Nafion 117) at 80 °C, and a methanol permeability of 4.82 × 10^?7 cm² s^?1. Meanwhile, it also presented outstanding oxidative stability. Atomic force microscope (AFM) micrographs showed that the hydrophilic domains of the sPAEPP‐100 membrane formed connected and narrow ionic channels, which contributed to its high proton conductivity and good dimensional stability. As a result, sPAEPP‐100 membrane displays excellent application prospect for fuel cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1097–1104     

Influence of adjusted hydrophilic–hydrophobic lengths in sulfonated multiblock copoly(ether sulfone) membranes for fuel cell application

Sulfonated multiblock copoly(ether sulfone)s applicable to proton exchange membrane fuel cells (PEMFCs) were synthesized by the coupling reaction of the hydroxyl‐terminated hydrophilic and hydrophobic oligomers with different lengths in the presence of highly reactive decafluorobiphenyl (DFB) as a chain extender to investigate the influence of each length on the membranes' properties, such as water uptake, proton conductivity, and morphology. Multiblock copolymers with high molecular weights (M_n > 50,000, M_w > 150,000) were obtained under mild reaction conditions. The resulting membranes demonstrated good oxidative stability for hot Fenton's reagent and maintained high water uptake (7.3–18.7 wt %) under a low relative humidity (50% RH). Proton conductivity of all membranes at 80 °C and 95% RH was higher than that of Nafion 117 membrane, and good proton conductivity of 7.0 × 10^?3 S/cm was obtained at 80 °C and 50% RH by optimizing the oligomer lengths. The surface morphology of the membranes was investigated by tapping mode atomic force microscopy (AFM), which showed that the multiblock copolymer membranes had a clearer surface hydrophilic/hydrophobic‐separated structure than that of the random copolymer, and contributed to good and effective proton conduction. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7332–7341, 2008     

Alternative proton-conducting electrolytes and their electrochemical performances

This study was focused on the performances of membrane electrode assemblies (MEAs) consisting of the proton–conducting 90PVA/3PWA/4GPTMS/1P₂O₅/2Gl and 80PVA/10PWA/6GPTMS/2P₂O₅/2Gl hybrid membranes as electrolytes together with a Pt/C electrode for proton exchange membrane fuel cells. The MEAs were fabricated and tested as a function of temperature and humidity, and yielded a current density value of about 350?mA?cm^?2 at 60?°C and 100% relative humidity (RH) for the membrane electrolyte 80PVA/10PWA/6GPTMS/2P₂O₅/2Gl. These values were compared with Nafion? membranes, and the single-cell performances based on proton-conducting organic/inorganic hybrid electrolytes were discussed. The test conditions employed were equivalent for each MEA that had an active area of 5?cm². These hybrid membranes showed a high proton conductivity in the range of 10^?3–10^?2 S cm^?1 at low temperatures, i.e., 60, 80, and 90?°C, and 50%, 75%, and 100% RH.     

Preparation and characterization of polybenzimidazole membranes prepared by gelation in phosphoric acid

Phosphoric acid doped poly (2, 2′‐(m‐phenylene)‐5, 5′‐bibenzimidazole) (PBI) membranes were prepared by dissolving PBI powders in 85% phosphoric acid at 190–200°C and then promoting gelation of the PBI by cooling the solutions to ?18°C. The extent of acid doping of the PBI membranes was controlled by immersing the membrane in aqueous phosphoric acid solutions of different concentrations (acid de‐doping). The process of the acid de‐doping was faster than acid doping of membrane cast from N,N‐dimethylacetamide (DMAc). The de‐doping process caused shrinkage of the PBI membrane and thus an increase in the membrane strength due to the packing of PBI chains according to the X‐ray diffraction analysis. The tensile stress and proton conductivity of the obtained PBI membranes with different acid doping levels were measured. For a PBI (η_IV: 0.58 dL · g^?1) membrane with an acid doping level of 7.0 (molar number of doped acid per mole repeat unit of PBI), the stress at break and proton conductivity at 120°C without humidification were 2.6 MPa and 5.1 × 10^?2 S · cm^?1, respectively. These results were comparable to those of the membranes cast from PBI solutions in DMAc. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and properties of novel sulfonated (co)polyimides bearing sulfonated aromatic pendant groups for PEFC applications

Novel sulfonated diamines bearing aromatic pendant groups, namely, 3,5‐diamino‐3′‐sulfo‐4′‐(4‐sulfophenoxy) benzophenone (DASSPB) and 3,5‐diamino‐3′‐sulfo‐4′‐(2,4‐disulfophenoxy) benzophenone (DASDSPB), were successfully synthesized. Novel side‐chain‐type sulfonated (co)polyimides (SPIs) were synthesized from these two diamines, 1,4,5,8‐naphthalene tetracarboxylic dianhydride (NTDA) and nonsulfonated diamines such as 4,4′‐bis(3‐aminophenoxy) phenyl sulfone (BAPPS). Tough and transparent membranes of SPIs with ion exchange capacity of 1.5–2.9 meq g^?1 were prepared. They showed good solubility and high thermal stability up to 300 °C. They showed isotropic membrane swelling in water, which was different from the main‐chain‐type and sulfoalkoxy‐based side‐chain‐type SPIs. The relative humidity (RH) and temperature dependence of proton conductivity were examined. At low RH, the novel SPI membranes showed much higher conductivity than the sulfoalkoxy‐based SPIs. They showed comparable or even higher proton conductivity than Nafion 112 in water at 60 °C (>0.10 S cm^?1). The membrane of NTDA‐DASDSPB/BAPPS (1/1)‐s displayed reasonably high proton conductivities of 0.05 and 0.30 S cm^?1 at 50 and 100% RH, respectively, at 120 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2862–2872, 2006     

Branched/Crosslinked Sulfonated Polyimide Membranes for Polymer Electrolyte Fuel Cells

Summary: Branched/crosslinked sulfonated polyimide membranes incorporating superior mechanical properties, high proton conductivity, and excellent fuel cell performance were successfully developed. The resulting polymer electrolytes displayed conductivity values of about 0.2 S · cm⁻¹ at 120 °C and 100% relative humidity. In a single H₂/O₂ fuel cell system at 90 °C, they exhibited reasonably high fuel cell performances comparable to that of Nafion 112.

The structure of the branched/crosslinked sulfonated polyimide membranes studied here.     

Structural modification of chitosan biopolymer as a novel polyelectrolyte membrane for green power generation

In the present study, a series of bioresource polyelectrolytes based on chitosan were synthesized and assessed for applicability in direct methanol fuel cells (DMFCs). A binary cross‐linking agent (sulfosuccinic acid/glutaraldehyde) was used for the structural modification of chitosan and membranes comprising various amounts of sulfosuccinic acid (0, 8, 12, and 16 wt% SSA/wt chitosan) were prepared. It was found that by increasing the sulfonate groups' content up to 16 wt%, proton conductivity and methanol permeability properties reach the values of 0.0452 S cm^?1 and 9.6 × 10^?7 cm² sec^?1, respectively. Based on the membrane selectivity evaluation and activation energy measurements of proton conduction, the optimum composition of cross‐linking agent was determined. The optimum composition resulted in a relatively high proton conductivity of 0.0452 S cm^?1 and a low methanol permeability of 9.6 × 10^?7 cm² sec^?1. Moreover, the optimum proton exchange membrane exhibited selectivity value of 47,100 in comparison with the corresponding value of 40,500 for Nafion® 117. The fabricated membranes showed acceptable oxidative and hydrolytic stability. Furthermore, single cell DMFC performance test revealed a power density of 17 mW cm^?2 at 30°C and 41 mW cm^?2 at 60°C in a 2 M methanol feed. Hence, prepared proton‐conducting bioresource ionomers could have promising potential in the field of green power generation as a low cost and biodegradable polyelectrolyte. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Proton conducting composite membranes from polysulfone and heteropolyacid for fuel cell applications

The viability of using composite membranes of heteropolyacid (HPA)/polysulfone (PSF), HPA/sulfonated polysulfone (SPSF) for use in proton exchange membrane fuel cells (PEMFC) was investigated. PSF and its sulfonated polymer, SPSF was solution‐blended with phosphotungstic acid, a commercially available HPA. Fourier transform infrared (FTIR) spectroscopy of the HPA–40/SPSF composite exhibited band shifts showing a possibility of intermolecular hydrogen bonding interaction between the HPA additive and the sulfonated polymer. The composite membranes exhibited improved mechanical strength and low water uptake. The conductivity of the composite membrane, HPA–40/SPSF, consisting of 40 wt % HPA and 60 wt % SPSF [with a degree of Sulfonation (DS) of 40%] exhibited a conductivity 0.089 S/cm at room temperature that linearly increased upto 0.14 S/cm at 120 °C, whereas the widely used commercial membrane Nafion 117, exhibited a room temperature conductivity of 0.1 S/cm that increased to only 0.12 S/cm at 120 °C. In contrast, the composite of HPA–40/PSF exhibited a proton conductivity of 0.02 S/cm at room temperature that increased only to 0.07 S/cm at a temperature of 100 °C. The incorporation of HPA into SPSF not only rendered the membranes suitable for elevated temperature operation of PEMFC but also provides an inexpensive alternative compared to Nafion. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1538–1547, 2005     

Synthesis and characterization of poly(arylene ether ketone)s bearing pendant sulfonic acid groups for proton exchange membrane materials

A bisphenol monomer (2,5‐dimethoxy)phenylhydroquinone was prepared and further polymerized to obtain poly(arylene ether ketone) copolymers containing methoxy groups. After demethylation and sulfobutylation, a series of novel poly(arylene ether ketone)s bearing pendant sulfonic acid group (SPAEKs) with different sulfonation content were obtained. The chemical structures of all the copolymers were analyzed by ¹H NMR and ¹³C NMR spectra. Flexible and tough membranes with reasonably good mechanical properties were prepared. The resulting side‐chain‐type SPAEK membranes showed good dimensional stability, and their water uptake and swelling ratio were lower than those of conventional main‐chain‐type SPAEK membranes with similar ion exchange capacity. Proton conductivities of these side‐chain‐type sulfonated copolymers were higher than 0.01 S/cm and increased gradually with increasing temperature. Their methanol permeability values were in the range of 1.97 × 10^?7–5.81 × 10^?7 cm²/s, which were much lower than that of Nafion 117. A combination of suitable proton conductivities, low water uptake, low swelling ratio, and high methanol resistance for these side‐chain‐type SPAEK films indicated that they may be good candidate material for proton exchange membrane in fuel cell applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010